Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Microphone Circuit between Microphone and Navigation Receiver Assembly

for Preparation Click here


DESCRIPTION

  1. The navigation receiver assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
  2. Using this circuit, the navigation receiver assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly (telephone microphone assembly) sends microphone signals to the navigation receiver assembly.

WIRING DIAGRAM


E259253E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY)
  1. Disconnect the I53 navigation receiver assembly connector.

  1. Disconnect the U7 roof console box assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I53-4 (MACC) - U7-10 (ACC)
    Always
    Below 1 Ω
    I53-5 (MIN+) - U7-9 (MIC+)
    Always
    Below 1 Ω
    I53-19 (MIN-) - U7-8 (MIC-)
    Always
    Below 1 Ω
    I53-6 (SNS2) - U7-14 (SGND)
    Always
    Below 1 Ω
    I53-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    I53-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    I53-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    I53-18 (SGND) - Body ground
    Always
    10 kΩ or higher
    I53-6 (SNS2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK NAVIGATION RECEIVER ASSEMBLY


    E259819E04
  1. Reconnect the navigation receiver assembly connector.

  1. Reconnect the roof console box assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I53-4 (MACC) - Body ground
    Ignition switch ACC
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I53-18 (SGND) - Body ground
    Always
    Below 1 Ω
    I53-19 (MIN-) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Component with harness connected
(Navigation Receiver Assembly)


NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


3.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)


    E160706E03
  1. Remove the roof console box assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    14 (SGND) - 8 (MIC-)
    Always
    Below 1 Ω



NG
Go to step 4
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.CHECK TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly with a new or normally functioning one (Click here).

  1. Check if the same problem occurs again.

    OK:
    Malfunction disappears.



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (Click here)
OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)