Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1655/37    Driver Side Seat Belt Buckle Switch Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat belt buckle switch LH circuit consists of the center airbag sensor and the front seat inner belt LH.
DTC B1655/37 is stored when a malfunction is detected in the seat belt buckle switch LH circuit.

DTC Code
Detection Condition
Trouble Area
B1655/37
When one of following conditions is met:
  1. The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch LH circuit for 2 seconds.
  2. Front seat inner belt LH malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Front seat inner belt assembly LH (Seat belt buckle switch LH)
  3. Center airbag sensor assembly

WIRING DIAGRAM


C158843E03


INSPECTION PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and front seat inner belt LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and the front seat inner belt LH.

  1. Check that the connectors (on the center airbag sensor side and front seat inner belt LH side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


3.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)

C172903E02

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O4-1 (LBE+) - Body ground
    Ignition switch ON
    Below 1 V
    O4-3 (LBE-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 11 (DBE+) and 12 (DBE-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-1 (LBE+) - O4-3 (LBE-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O4-1 (LBE+) - O4-3 (LBE-)
    Always
    1 MΩ or higher
    O4-1(LBE+) - Body ground
    Always
    1 MΩ or higher
    O4-3 (LBE-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


4.CHECK FRONT SEAT INNER BELT LH
C158841E07
  1. Connect the connector to the center airbag sensor and the front seat inner belt LH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    Codes other than DTC B1655/37 may be output at this time, but they are not related to this check.



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.REPLACE FRONT SEAT INNER BELT LH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat inner belt LH (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.


NEXT


6.CHECK CENTER AIRBAG SENSOR
C158841E07
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    Codes other than DTC B1655/37 may be output at this time, but they are not related to this check.

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ Cool Box)
    B
    NG (w/o Cool Box)
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

END