WATER PUMP > REMOVAL |
| 1. REMOVE NO. 1 ENGINE UNDER COVER |
![]() |
Remove the 3 screws and 5 bolts.
Unhook the engine under cover from the vehicle body as shown in the illustration.
| 2. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.
Remove the radiator cap. Then drain the coolant from the radiator.
Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.
Tighten the 2 cylinder block drain cock plugs.
Tighten the radiator drain cock plug by hand.

| 3. REMOVE V-BANK COVER SUB-ASSEMBLY |
![]() |
Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
| 4. REMOVE AIR CLEANER ASSEMBLY |
![]() |
Loosen the hose clamp and disconnect the air cleaner from the air cleaner hose.
Loosen the 2 bolts and remove the air cleaner with the grommet.
| 5. REMOVE AIR CLEANER HOSE ASSEMBLY |
![]() |
Disconnect the No. 2 ventilation hose.
Disconnect the vacuum hose.
Loosen the hose clamp and remove the air cleaner hose.
| 6. REMOVE INLET RADIATOR HOSE |
![]() |
Remove the inlet radiator hose.
| 7. DISCONNECT OUTLET RADIATOR HOSE |
![]() |
Disconnect the outlet radiator hose from the water inlet housing.
| 8. REMOVE FAN SHROUD |
![]() |
Loosen the 4 nuts holding the fluid coupling and fan.
Remove the fan and generator V belt .
![]() |
Detach the claw to open the No. 1 flexible hose clamp.
![]() |
Disconnect the reservoir hose from the upper radiator tank.
Remove the 2 bolts holding the fan shroud.
Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.
Remove the fan pulley from the fan bracket.
| 9. DISCONNECT WATER BY-PASS PIPE HOSE |
Remove the 3 bolts.
![]() |
Disconnect the 4 hoses and remove the water by-pass pipe.
| 10. DISCONNECT NO. 3 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System) |
![]() |
Disconnect the No. 3 air injection hose.
| 11. DISCONNECT NO. 2 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System) |
![]() |
Disconnect the connector and separate the wire harness clamp.
Disconnect the No. 2 air injection hose.
| 12. SEPARATE AIR PIPE SUB-ASSEMBLY (w/ Secondary Air Injection System) |
![]() |
Disconnect the connector and separate the 2 clamps and wire harness.
Remove bolt and separate the air pipe.
| 13. DISCONNECT NO. 5 WATER BY-PASS HOSE |
![]() |
Disconnect the No. 5 water by-pass hose.
| 14. REMOVE NO. 1 WATER BY-PASS HOSE |
![]() |
Disconnect the No. 1 water by-pass hose from the water by-pass joint and water inlet housing.
| 15. REMOVE INLET WATER HOUSING |
![]() |
Remove the 3 bolts and inlet water housing and disconnect the No. 3 water by-pass hose from the inlet water housing.
Remove the gasket from the water pump.
| 16. REMOVE WATER PUMP PULLEY |
![]() |
Using SST, hold the water pump pulley.
Remove the 4 bolts and water pump pulley.
| 17. REMOVE WATER PUMP ASSEMBLY |
![]() |
Remove the 8 bolts, water pump and gasket.