Home › Engine / Hybrid System › 3UR-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET

CYLINDER HEAD GASKET > INSTALLATION

for Preparation Click here



1. INSPECT CYLINDER HEAD SET BOLT


A122880E07
  1. Using a vernier caliper, measure the diameter of the elongated thread at the measuring point.

    Measuring point:
    94 mm (3.70 in.) for intake side bolt
    89 mm (3.50 in.) for exhaust side bolt

    Standard diameter:
    10.85 to 11.00 mm (0.427 to 0.433 in.)

    Minimum diameter:
    10.6 mm (0.417 in.)

    If the diameter is less than the minimum, replace the cylinder head bolt.

    HINT:
    If a visual check reveals no excessively thin areas, check the center of the bolt (see illustration) and find the area that has the lowest diameter.



2. INSPECT CYLINDER HEAD LH


A160689E04
  1. Using a precision straightedge and feeler gauge, measure the warpage of the surfaces where the cylinder head contacts the cylinder block and manifold.

    Standard Warpage:
    Item
    Specified Condition
    Cylinder block side
    0.05 mm (0.00197 in.)
    Intake manifold side
    0.08 mm (0.00315 in.)
    Exhaust manifold side
    0.05 mm (0.00197 in.)

    Maximum warpage:
    0.10 mm (0.00394 in.)

    If the warpage is more than the maximum, replace the cylinder head.



    A145553
  1. Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
    If cracked, replace the cylinder head.



3. INSPECT CYLINDER HEAD SUB-ASSEMBLY


A160689E04
  1. Using a precision straightedge and feeler gauge, measure the warpage of the surfaces where the cylinder head contacts the cylinder block and manifold.

    Standard Warpage:
    Item
    Specified Condition
    Cylinder block side
    0.05 mm (0.00197 in.)
    Intake manifold side
    0.08 mm (0.00315 in.)
    Exhaust manifold side
    0.05 mm (0.00197 in.)

    Maximum warpage:
    0.10 mm (0.00394 in.)

    If the warpage is more than the maximum, replace the cylinder head.



    A145553
  1. Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
    If cracked, replace the cylinder head.



4. INSTALL NO. 2 CYLINDER HEAD GASKET
  1. Check the piston protrusions for each cylinder.

    1. Clean the cylinder block with solvent.

    2. Set the piston of the cylinder to be measured to slightly ATDC.



    A148270E04
  1. Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

    NOTICE:
    1. Be careful of the installation direction.
    2. Make sure that no oil is on the front end (indicated by the arrows) of the cylinder head gasket.



5. INSTALL CYLINDER HEAD LH
  1. Place the cylinder head on the cylinder block.

    NOTICE:
    1. Gently place the cylinder head in order not to damage the gasket with the bottom part of the head.
    2. Ensure that no oil is on the mounting surface of the cylinder head.

    HINT:
    The cylinder head bolts are tightened in 3 progressive steps.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.



    A160737E06
  1. Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts with the plate washers in several steps, in the sequence shown in the illustration.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



    A132162E01
  1. Mark the front of the cylinder head bolts with paint.

  1. Further tighten the cylinder head bolts 90° and then an additional 90° as shown in the illustration.

  1. Check that the painted mark is now at a 180° angle from the front.



    A160736E06
  1. Install and uniformly tighten the 2 cylinder head bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



6. INSTALL CYLINDER HEAD GASKET
  1. Check the piston protrusions for each cylinder.

    1. Clean the cylinder block with solvent.

    2. Set the piston of the cylinder to be measured to slightly ATDC.



    A148268E04
  1. Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

    NOTICE:
    1. Be careful of the installation direction.
    2. Make sure that no oil is on the front end (indicated by the arrows) of the cylinder head gasket.



7. INSTALL CYLINDER HEAD SUB-ASSEMBLY
  1. Place the cylinder head on the cylinder block.

    NOTICE:
    1. Gently place the cylinder head in order not to damage the gasket with the bottom part of the head.
    2. Ensure that no oil is on the mounting surface of the cylinder head.

    HINT:
    The cylinder head bolts are tightened in 3 progressive steps.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.



    A160739E04
  1. Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts with the plate washers in several steps, in the sequence shown in the illustration.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



    A132162E01
  1. Mark the front of the cylinder head bolts with paint.

  1. Further tighten the cylinder head bolts 90° and then an additional 90° as shown in the illustration.

  1. Check that the painted mark is now at a 180° angle from the front.



    A160738E05
  1. Install and uniformly tighten the 2 cylinder head bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



8. INSTALL VALVE STEM CAP
  1. Apply a light coat of engine oil to the valve stem caps.

  1. Install the 32 valve stem caps to the cylinder head.



9. INSTALL VALVE LASH ADJUSTER ASSEMBLY
  1. Inspect the valve lash adjuster .

  1. Install the 32 valve lash adjusters to the cylinder head.

    NOTICE:
    Install the lash adjuster at the same place it was removed from.



10. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Apply engine oil to the lash adjuster tips and valve stem cap ends.



    A163454E01
  1. Install the 32 valve rocker arms as shown in the illustration.



11. INSTALL CAMSHAFTS
  1. Install the camshaft (Click here).



12. INSTALL EXHAUST MANIFOLD
  1. Install the exhaust manifold (Click here).