DTC B2325 LIN Communication Bus Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| B2325 | The main body ECU (cowl side junction block LH) detects a malfunction in the LIN communication bus between components related to the doors and sliding roof consecutively 3 times. |
|

| 1.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - REGULATOR MOTOR LH) |
![]() |
Disconnect the M2 power window regulator master switch assembly connector.
Disconnect the M3 front power window regulator motor assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M2-7 (LIN2) - M3-9 (LIN) | Always | Below 1 Ω |
| M2-7 (LIN2) or M3-9 (LIN) - Body ground | Always | 10 kΩ or higher |
Reconnect the power window regulator master switch assembly connector.
Reconnect the front power window regulator motor assembly LH connector.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - EACH ECU) |

Disconnect the H2 main body ECU connector.
Disconnect the M2 power window regulator master switch assembly connector.
Disconnect the L3 front power window regulator motor assembly RH connector.
Disconnect the U3* sliding roof drive gear sub-assembly connector.
Disconnect the V2 back door ECU connector.
Measure the resistance according to the value(s) in the tables below.
| Tester Connection | Condition | Specified Condition |
| H2-10 (LIN2) - M2-6 (LIN1) | Always | Below 1 Ω |
| H2-10 (LIN2) - L3-9 (LIN) | ||
| H2-10 (LIN2) - U3-3 (MPX1)* | ||
| H2-10 (LIN2) - V2-16 (MPX1) | ||
| H2-10 (LIN2) - Body ground | Always | 10 kΩ or higher |
Reconnect the main body ECU connector.
Reconnect the power window regulator master switch assembly connector.
Reconnect the front power window regulator motor assembly RH connector.
Reconnect the sliding roof drive gear sub-assembly connector*.
Reconnect the back door ECU connector.
|
| ||||
| OK | |
| 3.SYSTEM CHECK |
Check the vehicle specifications.
| Result | Proceed to |
| Vehicle with sliding roof | A |
| Vehicle without sliding roof | B |
|
| ||||
| A | |
| 4.CLEAR DTC |
Disconnect the U3 sliding roof drive gear sub-assembly connector.
Clear the DTC (Click here).
| NEXT | |
| 5.CHECK FOR DTC |
Recheck for DTCs (Click here).
| Result | Proceed to |
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
Reconnect the sliding roof driver gear sub-assembly connector.
|
| ||||
| A | |
| 6.CLEAR DTC |
Disconnect the M3 power window regulator motor assembly LH connector.
Clear the DTC (Click here).
| NEXT | |
| 7.CHECK FOR DTC |
Recheck for DTCs (Click here).
| Result | Proceed to |
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
Reconnect the power window regulator motor assembly LH connector.
|
| ||||
| A | |
| 8.CLEAR DTC |
Disconnect the M2 power window regulator master switch assembly connector.
Clear the DTC (Click here).
| NEXT | |
| 9.CHECK FOR DTC |
Recheck for DTCs (Click here).
| Result | Proceed to |
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
Reconnect the power window regulator master switch assembly connector.
|
| ||||
| A | |
| 10.CLEAR DTC |
Disconnect the L3 power window regulator motor assembly RH connector.
Clear the DTC (Click here).
| NEXT | |
| 11.CHECK FOR DTC |
Recheck for DTCs (Click here).
| Result | Proceed to |
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
Reconnect the power window regulator motor assembly RH connector.
|
| ||||
| A | |
| 12.CLEAR DTC |
Disconnect the V2 back door ECU connector.
Clear the DTC (Click here).
| NEXT | |
| 13.CHECK FOR DTC |
Recheck for DTCs (Click here).
| Result | Proceed to |
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
Reconnect the back door ECU connector.
|
| ||||
| A | ||
| ||