Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM

DTC    B2325    LIN Communication Bus Malfunction

for Preparation Click here


DESCRIPTION

The main body ECU intermittently monitors the LIN communication bus between the components related to the door and sliding roof. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the door and sliding roof is detected consecutively 3 times.

DTC Code
DTC Detection Condition
Trouble Area
B2325
The main body ECU (cowl side junction block LH) detects a malfunction in the LIN communication bus between components related to the doors and sliding roof consecutively 3 times.
  1. Power window regulator master switch assembly
  2. Front power window regulator motor assembly LH
  3. Front power window regulator motor assembly RH
  4. Sliding roof drive gear sub-assembly (w/ Sliding Roof)
  5. Back door ECU
  6. Main body ECU
  7. Harness or connector

WIRING DIAGRAM


E160665E02


INSPECTION PROCEDURE

NOTICE:
When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

HINT:
When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform the troubleshooting for the LIN communication stop DTC. Then perform the troubleshooting for DTC B2325.

1.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - REGULATOR MOTOR LH)


    E160673E01
  1. Disconnect the M2 power window regulator master switch assembly connector.

  1. Disconnect the M3 front power window regulator motor assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M2-7 (LIN2) - M3-9 (LIN)
    Always
    Below 1 Ω
    M2-7 (LIN2) or M3-9 (LIN) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the power window regulator master switch assembly connector.

  1. Reconnect the front power window regulator motor assembly LH connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - EACH ECU)

E160674E02

  1. Disconnect the H2 main body ECU connector.

  1. Disconnect the M2 power window regulator master switch assembly connector.

  1. Disconnect the L3 front power window regulator motor assembly RH connector.

  1. Disconnect the U3* sliding roof drive gear sub-assembly connector.

    HINT:
    *: w/ Sliding Roof

  1. Disconnect the V2 back door ECU connector.

  1. Measure the resistance according to the value(s) in the tables below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H2-10 (LIN2) - M2-6 (LIN1)
    Always
    Below 1 Ω
    H2-10 (LIN2) - L3-9 (LIN)
    H2-10 (LIN2) - U3-3 (MPX1)*
    H2-10 (LIN2) - V2-16 (MPX1)
    H2-10 (LIN2) - Body ground
    Always
    10 kΩ or higher

    HINT:
    *: w/ Sliding Roof

  1. Reconnect the main body ECU connector.

  1. Reconnect the power window regulator master switch assembly connector.

  1. Reconnect the front power window regulator motor assembly RH connector.

  1. Reconnect the sliding roof drive gear sub-assembly connector*.

    HINT:
    *: w/ Sliding Roof

  1. Reconnect the back door ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.SYSTEM CHECK
  1. Check the vehicle specifications.
    Result 
    Result
    Proceed to
    Vehicle with sliding roof
    A
    Vehicle without sliding roof
    B



B
Go to step 6
A


4.CLEAR DTC
  1. Disconnect the U3 sliding roof drive gear sub-assembly connector.

  1. Clear the DTC (Click here).


NEXT


5.CHECK FOR DTC
  1. Recheck for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B

  1. Reconnect the sliding roof driver gear sub-assembly connector.



B
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY
A


6.CLEAR DTC
  1. Disconnect the M3 power window regulator motor assembly LH connector.

  1. Clear the DTC (Click here).


NEXT


7.CHECK FOR DTC
  1. Recheck for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B

  1. Reconnect the power window regulator motor assembly LH connector.



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
A


8.CLEAR DTC
  1. Disconnect the M2 power window regulator master switch assembly connector.

  1. Clear the DTC (Click here).


NEXT


9.CHECK FOR DTC
  1. Recheck for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B

  1. Reconnect the power window regulator master switch assembly connector.



B
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
A


10.CLEAR DTC
  1. Disconnect the L3 power window regulator motor assembly RH connector.

  1. Clear the DTC (Click here).


NEXT


11.CHECK FOR DTC
  1. Recheck for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B

  1. Reconnect the power window regulator motor assembly RH connector.



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)
A


12.CLEAR DTC
  1. Disconnect the V2 back door ECU connector.

  1. Clear the DTC (Click here).


NEXT


13.CHECK FOR DTC
  1. Recheck for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B

  1. Reconnect the back door ECU connector.



B
REPLACE BACK DOOR ECU (Click here)
A

REPLACE MAIN BODY ECU