FRONT AIR CONDITIONING UNIT > INSTALLATION |
| 1. INSTALL ECU COVER |
Install the ECU cover with the 2 screws.
| 2. INSTALL FRONT AIR CONDITIONING UNIT |
![]() |
Temporarily tighten the air conditioning unit with the 3 bolts and 2 screws.
| 3. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY |
Connect the connector and clamp and install the wire harness.
Install the instrument panel reinforcement.
for Passenger Side:
Using a 12 mm hexagon wrench, install the 2 collars.
for Passenger Side:
Using a T40 "TORX" socket, install the 2 bolts.
for Driver Side:
Install the 3 bolts and 2 caps.
Install the instrument panel reinforcement with the 3 bolts and nut.

| *1 | "TORX" Bolt |
| *2 | Collar |
![]() |
Tighten the air conditioning unit with the 3 bolts and 2 screws.
Connect the connectors and clamps and install the wire harness.
Install the ground wire with the bolt.
| 4. INSTALL AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (w/ Cool Box) |
Sufficiently apply compressor oil to 4 new O-rings and the fitting surface of the hose joint.
Install the 4 O-rings to the air conditioner tube and accessory.
Install the air conditioner tube and accessory with the bolt.
![]() |
Connect the air conditioner tube and accessory with the 2 piping clamps.
| 5. INSTALL NO. 1 ECU INTEGRATION BRACKET |
Install the ECU integration bracket with the bolt and nut.
Connect the connectors and clamp.
| 6. INSTALL TURN SIGNAL FLASHER ASSEMBLY |
Install the turn signal flasher with the nut.
Connect the connector.
| 7. INSTALL MAIN BODY ECU |
Install the main body ECU with the bolt and nut.
Connect the connectors and clamp.
| 8. INSTALL REAR NO. 2 AIR DUCT |
Attach the 3 claws to install the air duct.
| 9. INSTALL REAR NO. 1 AIR DUCT |
Attach the 3 claws to install the air duct.
| 10. INSTALL STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column) |
| 11. INSTALL STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) |
| 12. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY |
| 13. INSTALL REAR NO. 4 AIR DUCT |
Attach the 4 claws to install the air duct.
Install the clip.
| 14. INSTALL REAR NO. 3 AIR DUCT |
Attach the 4 claws to install the air duct.
Install the clip.
| 15. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY (for 14 Speakers) |
![]() |
Install the amplifier with the 3 bolts.
Connect the 4 connectors.
| 16. INSTALL AUDIO AMPLIFIER COVER (for 14 Speakers) |
![]() |
Set the cover on the stereo amplifier assembly.
Attach the 3 clips.
| 17. INSTALL FRONT RH SEAT ASSEMBLY (for RH Side) |
for Manual Seat:
for Power Seat, w/ Leg Support Adjustment Switch:
for Power Seat, w/o Leg Support Adjustment Switch:
for Fold Down Seat Type:
| 18. INSTALL SEAT TRACK OUTER COVER RH (for Fold Down Seat Type) |
![]() |
Attach the 2 claws to install the seat track cover.
| 19. INSTALL SEAT TRACK INNER COVER RH (for Fold Down Seat Type) |
![]() |
Attach the 2 claws to install the seat track cover.
| 20. INSTALL FRONT SEAT TRACK BRACKET COVER INNER RH (for Fold Down Seat Type) |
![]() |
Attach the 4 claws in the order shown in the illustration to install the cover.
| 21. INSTALL FRONT SEAT TRACK BRACKET COVER OUTER RH (for Fold Down Seat Type) |
Lift up the seat track adjusting handle and move the seat to the rearmost position.
![]() |
Attach the 4 claws in the order shown in the illustration to install the cover.
| 22. INSTALL FRONT SEAT HEADREST ASSEMBLY (for RH Side) |
for Manual Seat:
for Power Seat:
for Fold Down Switch Type:
| 23. INSTALL FRONT LH SEAT ASSEMBLY (for LH Side) |
for Manual Seat:
for Power Seat, w/ Leg Support Adjustment Switch:
for Power Seat, w/o Leg Support Adjustment Switch:
| 24. INSTALL SEAT TRACK OUTER COVER LH (for LH Side) |
for Manual Seat:
for Power Seat:
| 25. INSTALL SEAT TRACK INNER COVER LH (for LH Side) |
for Manual Seat:
for Power Seat:
| 26. INSTALL FRONT SEAT TRACK BRACKET COVER INNER LH (for LH Side) |
for Manual Seat:
for Power Seat:
| 27. INSTALL FRONT SEAT TRACK BRACKET COVER OUTER LH (for LH Side) |
for Manual Seat:
for Power Seat:
| 28. INSTALL FRONT SEAT HEADREST ASSEMBLY (for LH Side) |
for Manual Seat:
for Power Seat, w/ Leg Support Adjustment Switch:
for Power Seat, w/o Leg Support Adjustment Switch:
| 29. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY |
| 30. CONNECT HEATER WATER OUTLET HOSE A |
![]() |
Connect the water hose onto the air conditioning unit.
| *a | View A |
| *b | Upper Side |
| *c | Yellow Paint Mark |
| 31. CONNECT HEATER WATER INLET HOSE A |
![]() |
Connect the water hose onto the air conditioning unit.
| *a | View A |
| *b | Upper Side |
| *c | White Paint Mark |
| 32. CONNECT COOLER REFRIGERANT LIQUID PIPE B |
![]() |
Remove the attached vinyl tape from the pipe.
Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the suction pipe.
Install the 2 O-rings on the suction pipe and liquid pipe.
Move the hook connector in the direction indicated by the arrow in the illustration.
Insert the pipe joint into the fitting hole securely and tighten the bolt.
| 33. INSPECT SHIFT LEVER POSITION |
When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that it moves smoothly and correctly into position.
Check that the shift lever does not stop when moving the shift lever from R to P, and check that the shift lever does not stick when moving the shift lever from D to S.
Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D and moves rearward after moving the shift lever to R.
If the operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.
| 34. ADJUST SHIFT LEVER POSITION |
Move the shift lever to the N position.
![]() |
Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press the lock piece from the back side to release the lock.
![]() |
Check that the adjust case's spring is applying enough tension to the shift control cable. Then press the lock piece to set the lock.
Return the cover of the adjust case to its original position.
Inspect the operation after the adjustment.
| 35. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 36. ADD ENGINE COOLANT |
Add engine coolant.
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 37. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 38. CHARGE REFRIGERANT |

Perform vacuum purging using a vacuum pump.
Charge refrigerant HFC-134a (R134a).
| Cool Box | Refrigerant Charging Amount |
| w/ Cool Box | 1080 to 1140 g (38.1 to 40.2 oz.) |
| w/o Cool Box | 920 to 980 g (32.4 to 34.6 oz.) |

Install the caps onto the service valves on the refrigerant line.
| 39. WARM UP ENGINE |
| 40. INSPECT FOR REFRIGERANT LEAK |
After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.
Perform the operation as follows:
![]() |
Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.
If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.
Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.
| 41. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Hook the engine under cover to the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.
| 42. CHECK SRS WARNING LIGHT |