CENTER AIRBAG SENSOR ASSEMBLY (w/ Cool Box) > INSTALLATION |
| 1. INSTALL AIRBAG SENSOR ASSEMBLY |
Confirm that the ignition switch is turned off.
Confirm that the negative battery terminal is disconnected.
Install the airbag sensor with the 3 bolts.
Confirm that there is no looseness by shaking the front airbag sensor.
![]() |
Connect the connector holder to lock the lever.
| *1 | Lever |
Confirm that the drip-proof sheet has not been removed and does not cut into the connectors.
| 2. INSTALL FRONT CONSOLE BOX |
Install the front console box with the 5 screws and 2 clips.
Attach the 2 clamps.
| 3. INSTALL REAR CONSOLE BOX ASSEMBLY |
Attach the 6 claws to install the rear console box.
Install the 2 screws and 4 bolts.
Connect the 2 connectors.
| 4. INSTALL COOLING BOX ASSEMBLY |
Attach the 4 clips and claw and install the cooling box assembly.
Install 4 new No. 1 cool box packings.
Install the 4 bolts.
Connect the 3 connectors.
| 5. INSTALL COOLING BOX TRAY |
Install the cooling box tray.
| 6. CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY |
Remove the attached vinyl tape from the air conditioner tube and accessory assembly.
Sufficiently apply compressor oil to 2 new O-rings and to the fitting surface of the cooling box assembly.
Install the 2 O-rings on the air conditioner tube and accessory assembly.
Connect the air conditioner tube and accessory assembly to the cooling box assembly with the 2 bolts.
| 7. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY |
Connect the connectors.
Attach the 6 clips to install the console panel.
Install the clip.
| 8. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY |
Attach the 12 clips to install the console panel.
| 9. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
![]() |
Install the shift lever knob and twist it in the direction indicated by the arrow.
| 10. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH |
Attach the 2 claws to install the sensor.
Connect the connectors.
Attach the 9 clips and claw to install the finish panel.
Install the 2 <A> bolts.
| 11. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.
Attach the 3 claws to install the hood lock lever
| 12. INSTALL INSTRUMENT SIDE PANEL LH |
![]() |
Attach the 7 claws to install the side panel.
| 13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 14. INSTALL COWL SIDE TRIM BOARD LH |
| 15. INSTALL FRONT DOOR SCUFF PLATE LH |
| 16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 17. INSPECT SRS WARNING LIGHT |
Inspect the SRS warning light (Click here).
| 18. CHARGE REFRIGERANT |

Perform vacuum purging using a vacuum pump.
Charge refrigerant HFC-134a (R134a).
| Cool Box | Refrigerant Charging Amount |
| w/ Cool Box | 1080 to 1140 g (38.1 to 40.2 oz.) |
| w/o Cool Box | 920 to 980 g (32.4 to 34.6 oz.) |

Install the caps onto the service valves on the refrigerant line.
| 19. WARM UP ENGINE |
| 20. INSPECT REFRIGERANT LEAK |
After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.
Perform the operation as follows:
![]() |
Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.
If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.
Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.