Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT

FRONT AIR CONDITIONING UNIT > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. TABLE OF BOLT, SCREW AND NUT


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet codes in the table below.



B262061E01



2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Switch A/C ON.

  1. Turn the blower switch to ON.

  1. Operate the cooler compressor with an engine speed of approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the remaining compressor oil from each component, in the cooler compressor.

  1. Stop the engine.



    E181845E02
  1. Remove the caps from the service valves on the refrigerant line.
    Text in Illustration 
    *1
    Low Pressure Service Valve
    *2
    High Pressure Service Valve

  1. Connect the refrigerant recovery unit.

  1. Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.

    NOTICE:
    Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



4. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



  1. Tighten the radiator drain cock plug by hand.


    A151835E01



6. REMOVE COOLER REFRIGERANT LIQUID PIPE B


I104456
  1. Remove the bolt, and slide the hook connector.



    I043960E02
  1. Disconnect the suction pipe and liquid pipe.

    NOTICE:
    1. Do not use a screwdriver or similar tool to disconnect the pipe.
    2. Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

  1. Remove the 2 O-rings from the suction pipe and liquid pipe.



7. REMOVE HEATER WATER INLET HOSE A


E191224
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose.

    NOTICE:
    1. Do not apply excessive force to the rear heater outlet water hose.
    2. Prepare a drain pan or cloth in case the coolant leaks.



8. REMOVE HEATER WATER OUTLET HOSE A


E191225
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose.

    NOTICE:
    1. Do not apply excessive force to the rear heater inlet water hose.
    2. Prepare a drain pan or cloth in case the coolant leaks.



9. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY
(Click here)


10. REMOVE FRONT SEAT HEADREST ASSEMBLY (for LH Side)


11. REMOVE FRONT SEAT TRACK BRACKET COVER INNER LH (for LH Side)
  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B232171E01
  1. Using a screwdriver, detach the 4 claws in the order shown in the illustration and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



12. REMOVE FRONT SEAT TRACK BRACKET COVER OUTER LH (for LH Side)


    B232172E01
  1. Using a screwdriver, detach the 4 claws in the order shown in the illustration and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



13. REMOVE SEAT TRACK INNER COVER LH (for LH Side)
  1. Lift up the seat track adjusting handle to move the seat to the foremost position.



    B191067
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



14. REMOVE SEAT TRACK OUTER COVER LH (for LH Side)


    B200255
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



15. REMOVE FRONT LH SEAT ASSEMBLY (for LH Side)


    B191041
  1. Remove the 2 bolts.

  1. Lift up the seat track adjusting handle to move the seat to the rearmost position.



    B191042
  1. Remove the 2 bolts.

  1. Lift up the seat track adjusting handle to move the seat to the center position.

  1. Disconnect the seat wire connectors under the seat.

  1. Remove the front seat assembly from the vehicle.

    NOTICE:
    Be careful not to damage the vehicle body.



16. REMOVE FRONT SEAT HEADREST ASSEMBLY (for RH Side)


17. REMOVE FRONT SEAT TRACK BRACKET COVER INNER RH (for RH Side)
  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B232171E01
  1. Using a screwdriver, detach the 4 claws in the order shown in the illustration and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



18. REMOVE FRONT SEAT TRACK BRACKET COVER OUTER RH (for RH Side)


    B232172E01
  1. Using a screwdriver, detach the 4 claws in the order shown in the illustration and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



19. REMOVE SEAT TRACK INNER COVER RH (for RH Side)
  1. Operate the power seat switch (slide switch) to move the seat to the foremost position.



    B191067
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



20. REMOVE SEAT TRACK OUTER COVER RH (for RH Side)


    B200255
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



21. REMOVE FRONT RH SEAT ASSEMBLY (for RH Side)
  1. Operate the power seat switch (slide switch) to move the seat to the foremost position.



    B191041
  1. Remove the 2 bolts.

  1. Operate the power seat switch (slide switch) to move the seat to the rearmost position.



    B194824
  1. Remove the 2 bolts.

  1. Operate the power seat switch (slide switch) to move the seat to the center position.



    B167188
  1. Operate the leg support adjustment switch to move the seat cushion to the open position.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the seat wire connectors under the seat.

  1. Remove the front seat assembly from the vehicle.

    NOTICE:
    Be careful not to damage the vehicle body.



22. REMOVE AUDIO AMPLIFIER COVER (for 14 Speakers)


    B190162
  1. Detach the 3 clips and remove the cover.



23. REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY (for 14 Speakers)


    B190161
  1. Disconnect the 4 connectors.

  1. Remove the 3 bolts and amplifier.



24. REMOVE REAR NO. 3 AIR DUCT


I104425
  1. Remove the clip.

  1. Detach the 4 claws and remove the air duct.



25. REMOVE REAR NO. 4 AIR DUCT


I104424
  1. Remove the clip.

  1. Detach the 4 claws and remove the air duct.



26. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


27. REMOVE STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)
(Click here)


28. REMOVE STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)
(Click here)


29. REMOVE REAR NO. 1 AIR DUCT


I104427
  1. Detach the 3 claws and remove the air duct.



30. REMOVE REAR NO. 2 AIR DUCT


I104426
  1. Detach the 3 claws and remove the air duct.



31. SEPARATE MAIN BODY ECU


I105827
  1. Disconnect the connectors and clamp.

  1. Remove the bolt and nut and separate the main body ECU.



32. REMOVE TURN SIGNAL FLASHER ASSEMBLY


I104429
  1. Disconnect the connector.

  1. Remove the nut and the turn signal flasher.



33. REMOVE NO. 1 ECU INTEGRATION BRACKET


I105828
  1. Disconnect the connectors and clamp.

  1. Remove the bolt and nut and the ECU integration bracket.



34. REMOVE AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (w/ Cool Box)


  1. Using SST, remove the piping clamp.

    SST
    09870-00025  



      E112919E06
    1. Attach SST to the piping clamp.

      HINT:
      Confirm the direction of the piping clamp claw and SST by referring to the illustration on the caution label.



    2. E112920E05
    3. Push down SST and release the clamp lock.
      Text in Illustration 
      *1
      Release lever
      *2
      Push
      *3
      Pull

      NOTICE:
      Be careful not to deform the tubes when pushing SST.

    4. Pull SST slightly and push the release lever, then remove the piping clamp with SST.

    5. Remove the piping clamp from SST.

  1. Disconnect the air conditioner tube and accessory.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



    I105747
  1. Remove the bolt and the air conditioner tube and accessory.

  1. Remove the 4 O-rings from the air conditioner tube and accessory.



35. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
  1. Disconnect the connectors and clamps and separate the wire harness.



  1. Remove the bolt and disconnect the ground wire.


    I105829



  1. Remove the instrument panel reinforcement.

    1. for Driver Side:
      Remove the 2 caps and 3 bolts.

    2. for Passenger Side:
      Using a T40 "TORX" socket, remove the 2 bolts.

      HINT:
      When removing the bolts, the collars may come off with the bolts.

    3. for Passenger Side:
      Using a 12 mm hexagon wrench, remove the 2 collars.



    4. Remove the 3 bolts, nut and instrument panel reinforcement.


      I104400E02

      Text in Illustration 
      *1
      "TORX" Bolt
      *2
      Collar



    I104432
  1. Disconnect the connector and clamp and separate the wire harness.



36. REMOVE FRONT AIR CONDITIONING UNIT


I104401
  1. Remove the 3 bolts, 2 screws and the air conditioning unit.



37. REMOVE ECU COVER


E183926
  1. Remove the 2 screws and ECU cover.