FRONT AIR CONDITIONING UNIT > REMOVAL |
| 1. TABLE OF BOLT, SCREW AND NUT |

| 2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM |
Start up the engine.
Switch A/C ON.
Turn the blower switch to ON.
Operate the cooler compressor with an engine speed of approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the remaining compressor oil from each component, in the cooler compressor.
Stop the engine.
![]() |
Remove the caps from the service valves on the refrigerant line.
| *1 | Low Pressure Service Valve |
| *2 | High Pressure Service Valve |
Connect the refrigerant recovery unit.
Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.
| 3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 4. REMOVE NO. 1 ENGINE UNDER COVER |
![]() |
Remove the 3 screws and 5 bolts.
Unhook the engine under cover from the vehicle body as shown in the illustration.
| 5. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.
Remove the radiator cap. Then drain the coolant from the radiator.
Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.
Tighten the 2 cylinder block drain cock plugs.
Tighten the radiator drain cock plug by hand.

| 6. REMOVE COOLER REFRIGERANT LIQUID PIPE B |
![]() |
Remove the bolt, and slide the hook connector.
![]() |
Disconnect the suction pipe and liquid pipe.
Remove the 2 O-rings from the suction pipe and liquid pipe.
| 7. REMOVE HEATER WATER INLET HOSE A |
![]() |
Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose.
| 8. REMOVE HEATER WATER OUTLET HOSE A |
![]() |
Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose.
| 9. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY |
| 10. REMOVE FRONT SEAT HEADREST ASSEMBLY (for LH Side) |
for Manual Seat:
for Power Seat:
| 11. REMOVE FRONT SEAT TRACK BRACKET COVER INNER LH (for LH Side) |
for Manual Seat:
for Power Seat:
| 12. REMOVE FRONT SEAT TRACK BRACKET COVER OUTER LH (for LH Side) |
for Manual Seat:
for Power Seat:
| 13. REMOVE SEAT TRACK INNER COVER LH (for LH Side) |
for Manual Seat:
for Power Seat:
| 14. REMOVE SEAT TRACK OUTER COVER LH (for LH Side) |
for Manual Seat:
for Power Seat:
| 15. REMOVE FRONT LH SEAT ASSEMBLY (for LH Side) |
for Manual Seat:
for Power Seat, w/ Leg Support Adjustment Switch:
for Power Seat, w/o Leg Support Adjustment Switch:
| 16. REMOVE FRONT SEAT HEADREST ASSEMBLY (for RH Side) |
for Manual Seat:
for Power Seat:
for Fold Down Seat Type:
| 17. REMOVE FRONT SEAT TRACK BRACKET COVER INNER RH (for RH Side) |
for Manual Seat:
for Power Seat:
for Fold Down Seat Type:
| 18. REMOVE FRONT SEAT TRACK BRACKET COVER OUTER RH (for Fold Down Seat Type) |
![]() |
Using a screwdriver, detach the 4 claws in the order shown in the illustration and remove the cover.
| 19. REMOVE SEAT TRACK INNER COVER RH (for Fold Down Seat Type) |
![]() |
Using a screwdriver, detach the 2 claws and remove the cover.
| 20. REMOVE SEAT TRACK OUTER COVER RH (for Fold Down Seat Type) |
Lift up the seat track adjusting handle to move the seat to the foremost position.
![]() |
Using a screwdriver, detach the 2 claws and remove the cover.
| 21. REMOVE FRONT RH SEAT ASSEMBLY (for RH Side) |
for Manual Seat:
for Power Seat, w/ Leg Support Adjustment Switch:
for Power Seat, w/o Leg Support Adjustment Switch:
for Fold Down Seat Type:
| 22. REMOVE AUDIO AMPLIFIER COVER (for 14 Speakers) |
![]() |
Detach the 3 clips and remove the cover.
| 23. REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY (for 14 Speakers) |
![]() |
Disconnect the 4 connectors.
Remove the 3 bolts and amplifier.
| 24. REMOVE REAR NO. 3 AIR DUCT |
![]() |
Remove the clip.
Detach the 4 claws and remove the air duct.
| 25. REMOVE REAR NO. 4 AIR DUCT |
![]() |
Remove the clip.
Detach the 4 claws and remove the air duct.
| 26. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY |
| 27. REMOVE STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column) |
| 28. REMOVE STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) |
| 29. REMOVE REAR NO. 1 AIR DUCT |
![]() |
Detach the 3 claws and remove the air duct.
| 30. REMOVE REAR NO. 2 AIR DUCT |
![]() |
Detach the 3 claws and remove the air duct.
| 31. SEPARATE MAIN BODY ECU |
![]() |
Disconnect the connectors and clamp.
Remove the bolt and nut and separate the main body ECU.
| 32. REMOVE TURN SIGNAL FLASHER ASSEMBLY |
![]() |
Disconnect the connector.
Remove the nut and the turn signal flasher.
| 33. REMOVE NO. 1 ECU INTEGRATION BRACKET |
![]() |
Disconnect the connectors and clamp.
Remove the bolt and nut and the ECU integration bracket.
| 34. REMOVE AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (w/ Cool Box) |
Using SST, remove the piping clamp.
![]() |
Attach SST to the piping clamp.
![]() |
Push down SST and release the clamp lock.
| *1 | Release lever |
| *2 | Push |
| *3 | Pull |
Pull SST slightly and push the release lever, then remove the piping clamp with SST.
Remove the piping clamp from SST.
Disconnect the air conditioner tube and accessory.
![]() |
Remove the bolt and the air conditioner tube and accessory.
Remove the 4 O-rings from the air conditioner tube and accessory.
| 35. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY |
Disconnect the connectors and clamps and separate the wire harness.
Remove the bolt and disconnect the ground wire.

Remove the instrument panel reinforcement.
for Driver Side:
Remove the 2 caps and 3 bolts.
for Passenger Side:
Using a T40 "TORX" socket, remove the 2 bolts.
for Passenger Side:
Using a 12 mm hexagon wrench, remove the 2 collars.
Remove the 3 bolts, nut and instrument panel reinforcement.

| *1 | "TORX" Bolt |
| *2 | Collar |
![]() |
Disconnect the connector and clamp and separate the wire harness.
| 36. REMOVE FRONT AIR CONDITIONING UNIT |
![]() |
Remove the 3 bolts, 2 screws and the air conditioning unit.
| 37. REMOVE ECU COVER |
![]() |
Remove the 2 screws and ECU cover.