Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


JUNCTION CONNECTOR


  1. NO. 1 JUNCTION CONNECTOR


    C202969E01


    Wiring Color 
    Junction Connector A Side
    Color (CANH Side)
    Color (CANL Side)
    Combination meter ECU (H91)*1, *2
    SB
    W
    No. 4 junction connector (H91)*1, *3
    SB
    W
    Center airbag sensor (H90)
    BR
    W
    Skid control ECU (A59)
    B
    W

    Wiring Color 
    Junction Connector B Side
    Color (CANH Side)
    Color (CANL Side)
    DLC3 (H93)
    V
    W
    Main body ECU (H103)*1
    L
    W
    No. 2 junction connector (H101)
    R
    W
    Steering angle sensor (H94)
    G
    W
    Power steering ECU (H106)
    GR
    W
    1. *1: for V Bus
    2. *2: w/o Air Suspension
    3. *3: w/ Air Suspension

    HINT:
    1. The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.
    2. The connectors can be connected to any terminals on the same side.



  2. NO. 2 JUNCTION CONNECTOR (for 2-pin Connector)


    C202970E01


    Wiring Color 
    Junction Connector B Side
    Color (CANH Side)
    Color (CANL Side)
    Bus buffer ECU (H105)
    P
    W
    No. 1 junction connector (H100)
    R
    W
    ECM (H99)
    GR
    W
    Air conditioning amplifier (H92)
    B
    W

    HINT:
    1. The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.
    2. The connectors can be connected to any terminals on the same side.



  3. NO. 2 JUNCTION CONNECTOR (for 22-pin Connector)


    C221688E01


    Terminal No. (Symbol)
    Wiring Color
    Destination
    H110-1 (CANH)
    B
    Air conditioning amplifier
    H110-12 (CANL)
    W
    Air conditioning amplifier
    H110-2 (CANH)*1
    BE
    4WD control ECU
    H110-13 (CANL)*1
    W
    4WD control ECU
    H110-3 (CANH)
    GR
    ECM
    H110-14 (CANL)
    W
    ECM
    H110-4 (CANH)
    R
    No. 1 junction connector
    H110-15 (CANL)
    W
    No. 1 junction connector
    H110-5 (CANH)*2
    P
    Bus buffer ECU
    H110-16 (CANL)*2
    W
    Bus buffer ECU
    1. *1: w/ 4WD
    2. *2: w/ Bus Buffer ECU

    HINT:
    1. The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.
    2. The connectors can be connected to any terminals on the same side.



  4. NO. 3 JUNCTION CONNECTOR (for 2-pin Connector)


    C193999E01


    Wiring Color 
    Junction Connector A Side
    Color (CANH Side)
    Color (CANL Side)
    Power seat control ECU (H97)*1
    GR
    W
    Multiplex tilt and telescopic ECU (H96)*1
    BE
    W
    Main body ECU (H104)*1, *2, *3
    B
    W
    No. 4 junction connector (H104)*1, *2, *4
    B
    W
    Combination meter ECU (H102)*1, *2, *4
    Y
    W

    Wiring Color 
    Junction Connector B Side
    Color (CANH Side)
    Color (CANL Side)
    Outer mirror control ECU (H98)*1
    LG
    W
    1. *1: w/ Seat Memory
    2. *2: for MS Bus
    3. *3: w/o Power Back Door
    4. *4: w/ Power Back Door

    HINT:
    1. The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.
    2. The connectors can be connected to any terminals on the same side.



  5. NO. 3 JUNCTION CONNECTOR (for 22-pin Connector)


    C172982E82


    Terminal No. (Symbol)
    Wiring Color
    Destination
    H111-1 (CANH)*1, *2, *4
    Y
    Combination meter ECU
    H111-12 (CANL)*1, *2, *4
    W
    Combination meter ECU
    H111-2 (CANH)*1
    BE
    Multiplex tilt and telescopic ECU
    H111-13 (CANL)*1
    W
    Multiplex tilt and telescopic ECU
    H111-3 (CANH)*1
    GR
    Power seat control ECU
    H111-14 (CANL)*1
    W
    Power seat control ECU
    H111-4 (CANH)*1, *2, *3
    B
    Main body ECU
    H111-15 (CANL)*1, *2, *3
    W
    Main body ECU
    H111-4 (CANH)*1, *2, *4
    B
    No. 4 junction connector
    H111-15 (CANL)*1, *2, *4
    W
    No. 4 junction connector
    H111-5 (CANH)*1
    LG
    Outer mirror control ECU
    H111-16 (CANL)*1
    W
    Outer mirror control ECU
    1. *1: w/ Seat Memory
    2. *2: for MS Bus
    3. *3: w/o Power Back Door
    4. *4: w/ Power Back Door

    HINT:
    1. The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.
    2. The connectors can be connected to any terminals on the same side.



  6. C135249
  7. TERMINALS OF CONNECTORS FOR JUNCTION CONNECTOR (NO. 1, NO. 2* and NO. 3*)

    1. *: for 2-pin Connector
    Terminal
    Terminal Symbol
    1
    CANH
    2
    CANL



  8. NO. 4 JUNCTION CONNECTOR (FRONT OF THE VEHICLE)


    E158731E01


    Terminal No. (Symbol)
    Wiring Color
    Destination
    O41-1 (CANH)*1, *4
    SB
    Combination meter ECU
    O41-7 (CANL)*1, *4
    W
    Combination meter ECU
    O41-2 (CANH)*1, *4
    L
    No. 1 junction connector
    O41-8 (CANL)*1, *4
    W
    No. 1 junction connector
    O41-5 (CANH)*2, *3
    B
    Main body ECU
    O41-11 (CANL)*2, *3
    W
    Main body ECU
    O41-6 (CANH)*2, *3
    P
    No. 3 junction connector
    O41-12 (CANL)*2, *3
    W
    No. 3 junction connector
    1. *1: for V Bus
    2. *2: for MS Bus
    3. *3: w/ Power Back Door
    4. *4: w/ Air Suspension

    HINT:
    1. The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.
    2. The connectors can be connected to any terminals on the same side.



  9. NO. 4 JUNCTION CONNECTOR (REAR OF THE VEHICLE)


    E158731E02


    Terminal No. (Symbol)
    Wiring Color
    Destination
    O42-1 (CANH)*2, *3
    B
    Power back door ECU
    O42-7 (CANL)*2, *3
    W
    Power back door ECU
    O42-6 (CANH)*1, *4
    B
    Suspension control ECU
    O42-12 (CANL)*1, *4
    W
    Suspension control ECU
    1. *1: for V Bus
    2. *2: for MS Bus
    3. *3: w/ Power Back Door
    4. *4: w/ Air Suspension

    HINT:
    1. The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.
    2. The connectors can be connected to any terminals on the same side.


CHECK DLC3
H102628E01
  1. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-14 (CANL)
    V - W
    Ignition switch off
    54 to 69 Ω
    H19-6 (CANH) - H19-4 (CG)
    V - W-B
    Ignition switch off
    200 Ω or higher
    H19-14 (CANL) - H19-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H19-6 (CANH) - H19-16 (BAT)
    V - P
    Ignition switch off
    6 kΩ or higher
    H19-14 (CANL) - H19-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK SKID CONTROL ECU

C240485E01

  1. Disconnect the A19 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A19-12 (CANH) - A19-13 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    A19-12 (CANH) - A19-16 (GND1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    A19-13 (CANL) - A19-16 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A19-12 (CANH) - A19-1 (+BM)
    B - L
    Ignition switch off
    6 kΩ or higher
    A19-13 (CANL) - A19-1 (+BM)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK MAIN BODY ECU

C172609E08

  1. Disconnect the H2, DB and DD ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H2-5 (CANH) - H2-6 (CANL)*1
    L - W
    Ignition switch off
    54 to 69 Ω
    H2-5 (CANH) - DD-62 (GND1)*1
    L - W-B
    Ignition switch off
    200 Ω or higher
    H2-6 (CANL) - DD-62 (GND1)*1
    W - W-B
    Ignition switch off
    200 Ω or higher
    H2-5 (CANH) - DB-13 (BECU)*1
    L - GR
    Ignition switch off
    6 kΩ or higher
    H2-6 (CANL) - DB-13 (BECU)*1
    W - GR
    Ignition switch off
    6 kΩ or higher
    H2-16 (CANP) - H2-15 (CANN)*2
    B - W
    Ignition switch off
    108 to 132 Ω
    H2-16 (CANP) - DD-62 (GND1)*2
    B - W-B
    Ignition switch off
    200 Ω or higher
    H2-15 (CANN) - DD-62 (GND1)*2
    W - W-B
    Ignition switch off
    200 Ω or higher
    H2-16 (CANP) - DB-13 (BECU)*2
    B - GR
    Ignition switch off
    6 kΩ or higher
    H2-15 (CANN) - DB-13 (BECU)*2
    W - GR
    Ignition switch off
    6 kΩ or higher

    1. *1: for V Bus
    2. *2: for MS Bus


CHECK ECM

C159489E07

  1. Disconnect the A27 and D56 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A27-10 (CANH) - A27-11 (CANL)
    GR - W
    Ignition switch off
    108 to 132 Ω
    A27-10 (CANH) - D56-81 (E1)
    GR - BR
    Ignition switch off
    200 Ω or higher
    A27-11 (CANL) - D56-81 (E1)
    W - BR
    Ignition switch off
    200 Ω or higher
    A27-10 (CANH) - A27-3 (+B)
    GR - GR
    Ignition switch off
    6 kΩ or higher
    A27-11 (CANL) - A27-3 (+B)
    W - GR
    Ignition switch off
    6 kΩ or higher


CHECK AIR CONDITIONING AMPLIFIER

C159478E04

  1. Disconnect the H24 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H24-11 (CANH) - H24-12 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    H24-11 (CANH) - H24-14 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    H24-12 (CANL) - H24-14 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H24-11 (CANH) - H24-21 (B)
    B - R
    Ignition switch off
    6 kΩ or higher
    H24-12 (CANL) - H24-21 (B)
    W - R
    Ignition switch off
    6 kΩ or higher


CHECK CENTER AIRBAG SENSOR

C162022E02

  1. Disconnect the H56 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H56-13 (CANH) - H56-22 (CANL)
    BR - W
    Ignition switch off
    54 to 69 Ω
    H56-13 (CANH) - H56-25 (E1)
    BR - W-B
    Ignition switch off
    200 Ω or higher
    H56-22 (CANL) - H56-25 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H56-13 (CANH) - H19-16 (BAT)
    BR - P
    Ignition switch off
    6 kΩ or higher
    H56-22 (CANL) - H19-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK COMBINATION METER ECU

C159488E04

  1. Disconnect the H37 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H37-33 (CANH) - H37-34 (CANL)*1
    SB - W
    Ignition switch off
    108 to 132 Ω
    H37-33 (CANH) - H37-40 (E1)*1
    SB - W-B
    Ignition switch off
    200 Ω or higher
    H37-34 (CANL) - H37-40 (E1)*1
    W - W-B
    Ignition switch off
    200 Ω or higher
    H37-33 (CANH) - H37-18 (B)*1
    SB - LG
    Ignition switch off
    6 kΩ or higher
    H37-34 (CANL) - H37-18 (B)*1
    W - LG
    Ignition switch off
    6 kΩ or higher
    H37-22 (CANH) - H37-21 (CANL)*2
    Y - W
    Ignition switch off
    108 to 132 Ω
    H37-22 (CANH) - H37-40 (E1)*2
    Y - W-B
    Ignition switch off
    200 Ω or higher
    H37-21 (CANL) - H37-40 (E1)*2
    W - W-B
    Ignition switch off
    200 Ω or higher
    H37-22 (CANH) - H37-18 (B)*2
    Y - LG
    Ignition switch off
    6 kΩ or higher
    H37-21 (CANL) - H37-18 (B)*2
    W - LG
    Ignition switch off
    6 kΩ or higher

    1. *1: for V Bus
    2. *2: for MS Bus


CHECK STEERING ANGLE SENSOR

C159491E02

  1. Disconnect the H6 sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H6-10 (CANH) - H6-9 (CANL)
    G - W
    Ignition switch off
    54 to 69 Ω
    H6-10 (CANH) - H6-2 (ESS)
    G - W-B
    Ignition switch off
    200 Ω or higher
    H6-9 (CANL) - H6-2 (ESS)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H6-10 (CANH) - H6-3 (BAT)
    G - R
    Ignition switch off
    6 kΩ or higher
    H6-9 (CANL) - H6-3 (BAT)
    W - R
    Ignition switch off
    6 kΩ or higher


CHECK 4WD CONTROL ECU (w/ 4WD)

C159479E05

  1. Disconnect the A28 and A29 ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A28-19 (CANH) - A28-20 (CANL)
    BE - W
    Ignition switch off
    54 to 69 Ω
    A28-19 (CANH) - A29-4 (GND)
    BE - W-B
    Ignition switch off
    200 Ω or higher
    A28-20 (CANL) - A29-4 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A28-19 (CANH) - H19-16 (BAT)
    BE - P
    Ignition switch off
    6 kΩ or higher
    A28-20 (CANL) - H19-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK BUS BUFFER ECU (w/ Bus Buffer ECU)
C159601E02
  1. Disconnect the H66 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H66-3 (CAN+) - H66-2 (CAN-)
    P - W
    Ignition switch off
    54 to 69 Ω


CHECK POWER SEAT CONTROL ECU (w/ Seat Memory)

C159480E04

  1. Disconnect the X10 and X11 ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    X11-5 (CANH) - X11-1 (CANL)
    GR - W
    Ignition switch off
    54 to 69 Ω
    X11-5 (CANH) - X10-1 (GND)
    GR - W-B
    Ignition switch off
    200 Ω or higher
    X11-1 (CANL) - X10-1 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    X11-5 (CANH) - X10-5 (+B)
    GR - L
    Ignition switch off
    6 kΩ or higher
    X11-1 (CANL) - X10-5 (+B)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK OUTER MIRROR CONTROL ECU (w/ Seat Memory)

C159485E02

  1. Disconnect the M7 and M8 ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    M8-1 (CAN) - M8-21 (CGND)
    LG - W
    Ignition switch off
    54 to 69 Ω
    M8-1 (CAN) - M7-9 (GND)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    M8-21 (CGND) - M7-9 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    M8-1 (CAN) - M7-3 (B)
    LG - R
    Ignition switch off
    6 kΩ or higher
    M8-21 (CGND) - M7-3 (B)
    W - R
    Ignition switch off
    6 kΩ or higher


CHECK MULTIPLEX TILT AND TELESCOPIC ECU (w/ Seat Memory)

C159486E02

  1. Disconnect the H57 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H57-5 (CANH) - H57-14 (CANL)
    BE - W
    Ignition switch off
    54 to 69 Ω
    H57-5 (CANH) - H57-11 (GND)
    BE - W-B
    Ignition switch off
    200 Ω or higher
    H57-14 (CANL) - H57-11 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H57-5 (CANH) - H57-2 (+B)
    BE - V
    Ignition switch off
    6 kΩ or higher
    H57-14 (CANL) - H57-2 (+B)
    W - V
    Ignition switch off
    6 kΩ or higher


CHECK POWER STEERING ECU

E158722E01

  1. Disconnect the H38 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H38-8 (CANH) - H38-3 (CANL)
    GR - W
    Ignition switch off
    54 to 69 Ω
    H38-8 (CANH) - H38-2 (GND)
    GR - W-B
    Ignition switch off
    200 Ω or higher
    H38-3 (CANL) - H38-2 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H38-8 (CANH) - H19-16 (BAT)
    GR - P
    Ignition switch off
    6 kΩ or higher
    H38-3 (CANL) - H19-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK SUSPENSION CONTROL ECU (w/ Air Suspension)


  1. w/ AVS:


    E158723E01


    1. Disconnect the O17 and O18 ECU connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Switch Condition
      Specified Condition
      O18-30 (CANH) - O18-29 (CANL)
      B - W
      Ignition switch off
      54 to 69 Ω
      O18-30 (CANH) - O18-1 (GND)
      B - W-B
      Ignition switch off
      200 Ω or higher
      O18-29 (CANL) - O18-1 (GND)
      W - W-B
      Ignition switch off
      200 Ω or higher
      O18-30 (CANH) - O17-6 (B)
      B - SB
      Ignition switch off
      6 kΩ or higher
      O18-29 (CANL) - O17-6 (B)
      W - SB
      Ignition switch off
      6 kΩ or higher



  2. w/o AVS:


    E158724E01


    1. Disconnect the O19 ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Switch Condition
      Specified Condition
      O19-29 (CANH) - O19-28 (CANL)
      B - W
      Ignition switch off
      54 to 69 Ω
      O19-29 (CANH) - O19-22 (GND)
      B - W-B
      Ignition switch off
      200 Ω or higher
      O19-28 (CANL) - O19-22 (GND)
      W - W-B
      Ignition switch off
      200 Ω or higher
      O19-29 (CANH) - O19-24 (B)
      B - SB
      Ignition switch off
      6 kΩ or higher
      O19-28 (CANL) - O19-24 (B)
      W - SB
      Ignition switch off
      6 kΩ or higher


CHECK POWER BACK DOOR ECU (w/ Power Back Door)

H100802E07

  1. Disconnect the O30 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    O30-6 (CANP) - O30-5 (CANN)
    B - W
    Ignition switch off
    54 to 69 Ω
    O30-6 (CANP) - O30-11 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    O30-5 (CANN) - O30-11 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    O30-6 (CANP) - O30-12 (B)
    B - L
    Ignition switch off
    6 kΩ or higher
    O30-5 (CANN) - O30-12 (B)
    W - L
    Ignition switch off
    6 kΩ or higher