Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


JUNCTION CONNECTOR


  1. NO. 1 JUNCTION CONNECTOR


    C221688E02


    Text in Illustration 
    *a
    to Center Airbag Sensor
    *b
    to Combination Meter ECU (w/o Air Suspension) or No. 4 Junction Connector (w/ Air Suspension)
    *c
    to DLC3
    *d
    to Steering Angle Sensor
    *e
    to No. 2 Junction Connector
    *f
    to Main Body ECU
    *g
    to Power Steering ECU
    *h
    to Skid Control ECU

    Terminal No. (Symbol)
    Wiring Color
    Connect to
    H115-1 (CANH)
    BR
    Center Airbag Sensor
    H115-12 (CANL)
    W
    Center Airbag Sensor
    H115-2 (CANH)*1
    SB
    Combination Meter ECU
    H115-13 (CANL)*1
    W
    Combination Meter ECU
    H115-2 (CANH)*2
    L
    No. 4 Junction Connector
    H115-13 (CANL)*2
    W
    No. 4 Junction Connector
    H115-3 (CANH)
    V
    DLC3
    H115-14 (CANL)
    W
    DLC3
    H115-4 (CANH)
    G
    Steering Angle Sensor
    H115-15 (CANL)
    W
    Steering Angle Sensor
    H115-5 (CANH)
    R
    No. 2 Junction Connector
    H115-16 (CANL)
    W
    No. 2 Junction Connector
    H115-6 (CANH)
    L
    Main Body ECU
    H115-17 (CANL)
    W
    Main Body ECU
    H115-7 (CANH)
    GR
    Power Steering ECU
    H115-18 (CANL)
    W
    Power Steering ECU
    H115-9 (CANH)
    B
    Skid Control ECU
    H115-20 (CANL)
    W
    Skid Control ECU
    1. *1: w/o Air Suspension
    2. *2: w/ Air Suspension

    HINT:
    1. The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.
    2. The connectors can be connected to any terminals on the same side.



  2. NO. 2 JUNCTION CONNECTOR


    C221688E03


    Text in Illustration 
    *a
    to Air Conditioning Amplifier
    *b
    to 4WD Control ECU (w/ 4WD)
    *c
    to ECM
    *d
    No. 1 Junction Connector
    *e
    to Bus Buffer ECU (w/ Bus Buffer ECU)
    -
    -

    Terminal No. (Symbol)
    Wiring Color
    Destination
    H110-1 (CANH)
    B
    Air Conditioning Amplifier
    H110-12 (CANL)
    W
    Air Conditioning Amplifier
    H110-2 (CANH)*1
    BE
    4WD Control ECU
    H110-13 (CANL)*1
    W
    4WD Control ECU
    H110-3 (CANH)
    GR
    ECM
    H110-14 (CANL)
    W
    ECM
    H110-4 (CANH)
    R
    No. 1 Junction Connector
    H110-15 (CANL)
    W
    No. 1 Junction Connector
    H110-5 (CANH)*2
    P
    Bus Buffer ECU
    H110-16 (CANL)*2
    W
    Bus Buffer ECU
    1. *1: w/ 4WD
    2. *2: w/ Bus Buffer ECU

    HINT:
    1. The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.
    2. The connectors can be connected to any terminals on the same side.



  3. NO. 3 JUNCTION CONNECTOR (w/ Seat Memory)


    C221688E04


    Text in Illustration 
    *a
    to Combination Meter ECU
    *b
    to Multiplex Tilt and Telescopic ECU
    *c
    to Power Seat Control ECU
    *d
    to Main Body ECU (w/o Power Back Door) or No. 4 Junction Connector (w/ Power Back Door)
    *e
    to Outer Mirror Control ECU
    -
    -

    Terminal No. (Symbol)
    Wiring Color
    Connect to
    H111-1 (CANH)
    Y
    Combination Meter ECU
    H111-12 (CANL)
    W
    Combination Meter ECU
    H111-2 (CANH)
    BE
    Multiplex Tilt and Telescopic ECU
    H111-13 (CANL)
    W
    Multiplex Tilt and Telescopic ECU
    H111-3 (CANH)
    GR
    Power Seat Control ECU
    H111-14 (CANL)
    W
    Power Seat Control ECU
    H111-4 (CANH)*1
    B
    Main Body ECU
    H111-15 (CANL)*1
    W
    Main Body ECU
    H111-4 (CANH)*2
    B
    No. 4 Junction Connector
    H111-15 (CANL)*2
    W
    No. 4 Junction Connector
    H111-5 (CANH)
    LG
    Outer Mirror Control ECU
    H111-16 (CANL)
    W
    Outer Mirror Control ECU
    1. *1: w/o Power Back Door
    2. *2: w/ Power Back Door

    HINT:
    1. The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.
    2. The connectors can be connected to any terminals on the same side.



  4. NO. 4 JUNCTION CONNECTOR (FRONT OF THE VEHICLE)


    E158731E03


    Text in Illustration 
    *a
    to Combination Meter ECU
    *b
    to No. 1 Junction Connector
    *c
    to Main Body ECU
    *d
    to No. 3 Junction Connector
    *e
    Front of the vehicle
    -
    -

    Terminal No. (Symbol)
    Wiring Color
    Connect to
    O41-1 (CANH)*1, *4
    SB
    Combination Meter ECU
    O41-7 (CANL)*1, *4
    W
    Combination Meter ECU
    O41-2 (CANH)*1, *4
    L
    No. 1 Junction Connector
    O41-8 (CANL)*1, *4
    W
    No. 1 Junction Connector
    O41-5 (CANH)*2, *3
    B
    Main Body ECU
    O41-11 (CANL)*2, *3
    W
    Main Body ECU
    O41-6 (CANH)*2, *3
    P
    No. 3 Junction Connector
    O41-12 (CANL)*2, *3
    W
    No. 3 Junction Connector
    1. *1: for V Bus
    2. *2: for MS Bus
    3. *3: w/ Power Back Door
    4. *4: w/ Air Suspension

    HINT:
    1. The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.
    2. The connectors can be connected to any terminals on the same side.



  5. NO. 4 JUNCTION CONNECTOR (REAR OF THE VEHICLE)


    E158731E04


    Text in Illustration 
    *a
    to Power Back Door ECU (w/ Power Back Door)
    *b
    to Suspension Control ECU (w/ Air Suspension)
    *c
    Rear of the vehicle
    -
    -

    Terminal No. (Symbol)
    Wiring Color
    Connect to
    O42-1 (CANH)*2, *3
    B
    Power Back Door ECU
    O42-7 (CANL)*2, *3
    W
    Power Back Door ECU
    O42-6 (CANH)*1, *4
    B
    Suspension Control ECU
    O42-12 (CANL)*1, *4
    W
    Suspension Control ECU
    1. *1: for V Bus
    2. *2: for MS Bus
    3. *3: w/ Power Back Door
    4. *4: w/ Air Suspension

    HINT:
    1. The connectors connected to the junction connector can be distinguished by the colors of the bus lines and the connecting side of the connector.
    2. The connectors can be connected to any terminals on the same side.


CHECK DLC3
H102621E92
  1. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-14 (CANL)
    V - W
    Ignition switch off
    54 to 69 Ω
    H19-6 (CANH) - H19-4 (CG)
    V - W-B
    Ignition switch off
    200 Ω or higher
    H19-14 (CANL) - H19-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H19-6 (CANH) - H19-16 (BAT)
    V - P
    Ignition switch off
    6 kΩ or higher
    H19-14 (CANL) - H19-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK SKID CONTROL ECU

C240485E01

  1. Disconnect the A19 skid control ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A19-12 (CANH) - A19-13 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    A19-12 (CANH) - A19-16 (GND1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    A19-13 (CANL) - A19-16 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A19-12 (CANH) - A19-1 (+BM)
    B - L
    Ignition switch off
    6 kΩ or higher
    A19-13 (CANL) - A19-1 (+BM)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK MAIN BODY ECU

C172609E09


Text in Illustration 
*A
for V Bus
*B
for MS Bus
  1. Disconnect the H2, DB and DD main body ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H2-5 (CANH) - H2-6 (CANL)*1
    L - W
    Ignition switch off
    54 to 69 Ω
    H2-5 (CANH) - DD-62 (GND1)*1
    L - W-B
    Ignition switch off
    200 Ω or higher
    H2-6 (CANL) - DD-62 (GND1)*1
    W - W-B
    Ignition switch off
    200 Ω or higher
    H2-5 (CANH) - DB-13 (BECU)*1
    L - GR
    Ignition switch off
    6 kΩ or higher
    H2-6 (CANL) - DB-13 (BECU)*1
    W - GR
    Ignition switch off
    6 kΩ or higher
    H2-16 (CANP) - H2-15 (CANN)*2
    B - W
    Ignition switch off
    108 to 132 Ω
    H2-16 (CANP) - DD-62 (GND1)*2
    B - W-B
    Ignition switch off
    200 Ω or higher
    H2-15 (CANN) - DD-62 (GND1)*2
    W - W-B
    Ignition switch off
    200 Ω or higher
    H2-16 (CANP) - DB-13 (BECU)*2
    B - GR
    Ignition switch off
    6 kΩ or higher
    H2-15 (CANN) - DB-13 (BECU)*2
    W - GR
    Ignition switch off
    6 kΩ or higher

    1. *1: for V Bus
    2. *2: for MS Bus


CHECK ECM

C159489E23

  1. Disconnect the A27 and D56 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A27-10 (CANH) - A27-11 (CANL)
    GR - W
    Ignition switch off
    108 to 132 Ω
    A27-10 (CANH) - D56-81 (E1)
    GR - BR
    Ignition switch off
    200 Ω or higher
    A27-11 (CANL) - D56-81 (E1)
    W - BR
    Ignition switch off
    200 Ω or higher
    A27-10 (CANH) - A27-3 (+B)
    GR - GR
    Ignition switch off
    6 kΩ or higher
    A27-11 (CANL) - A27-3 (+B)
    W - GR
    Ignition switch off
    6 kΩ or higher


CHECK AIR CONDITIONING AMPLIFIER

C159478E05

  1. Disconnect the H24 air conditioning amplifier connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H24-11 (CANH) - H24-12 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    H24-11 (CANH) - H24-14 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    H24-12 (CANL) - H24-14 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H24-11 (CANH) - H24-21 (B)
    B - R
    Ignition switch off
    6 kΩ or higher
    H24-12 (CANL) - H24-21 (B)
    W - R
    Ignition switch off
    6 kΩ or higher


CHECK CENTER AIRBAG SENSOR

C162022E03

  1. Disconnect the H56 center airbag sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H56-13 (CANH) - H56-22 (CANL)
    BR - W
    Ignition switch off
    54 to 69 Ω
    H56-13 (CANH) - H56-25 (E1)
    BR - W-B
    Ignition switch off
    200 Ω or higher
    H56-22 (CANL) - H56-25 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H56-13 (CANH) - H19-16 (BAT)
    BR - P
    Ignition switch off
    6 kΩ or higher
    H56-22 (CANL) - H19-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK COMBINATION METER ECU

C159488E07


Text in Illustration 
*A
for V Bus
*B
for MS Bus
  1. Disconnect the H37 combination meter ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H37-33 (CANH) - H37-34 (CANL)*1
    SB - W
    Ignition switch off
    108 to 132 Ω
    H37-33 (CANH) - H37-40 (E1)*1
    SB - W-B
    Ignition switch off
    200 Ω or higher
    H37-34 (CANL) - H37-40 (E1)*1
    W - W-B
    Ignition switch off
    200 Ω or higher
    H37-33 (CANH) - H37-18 (B)*1
    SB - LG
    Ignition switch off
    6 kΩ or higher
    H37-34 (CANL) - H37-18 (B)*1
    W - LG
    Ignition switch off
    6 kΩ or higher
    H37-22 (CANH) - H37-21 (CANL)*2
    Y - W
    Ignition switch off
    108 to 132 Ω
    H37-22 (CANH) - H37-40 (E1)*2
    Y - W-B
    Ignition switch off
    200 Ω or higher
    H37-21 (CANL) - H37-40 (E1)*2
    W - W-B
    Ignition switch off
    200 Ω or higher
    H37-22 (CANH) - H37-18 (B)*2
    Y - LG
    Ignition switch off
    6 kΩ or higher
    H37-21 (CANL) - H37-18 (B)*2
    W - LG
    Ignition switch off
    6 kΩ or higher

    1. *1: for V Bus
    2. *2: for MS Bus


CHECK STEERING ANGLE SENSOR

C159491E03

  1. Disconnect the H6 steering angle sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H6-10 (CANH) - H6-9 (CANL)
    G - W
    Ignition switch off
    54 to 69 Ω
    H6-10 (CANH) - H6-2 (ESS)
    G - W-B
    Ignition switch off
    200 Ω or higher
    H6-9 (CANL) - H6-2 (ESS)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H6-10 (CANH) - H6-3 (BAT)
    G - R
    Ignition switch off
    6 kΩ or higher
    H6-9 (CANL) - H6-3 (BAT)
    W - R
    Ignition switch off
    6 kΩ or higher


CHECK 4WD CONTROL ECU (w/ 4WD)

C159479E07

  1. Disconnect the A28 and A29 4WD control ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A28-19 (CANH) - A28-20 (CANL)
    BE - W
    Ignition switch off
    54 to 69 Ω
    A28-19 (CANH) - A29-4 (GND)
    BE - W-B
    Ignition switch off
    200 Ω or higher
    A28-20 (CANL) - A29-4 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A28-19 (CANH) - H19-16 (BAT)
    BE - P
    Ignition switch off
    6 kΩ or higher
    A28-20 (CANL) - H19-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK BUS BUFFER ECU (w/ Bus Buffer ECU)
C159601E04
  1. Disconnect the H66 bus buffer ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H66-3 (CAN+) - H66-2 (CAN-)
    P - W
    Ignition switch off
    54 to 69 Ω


CHECK POWER SEAT CONTROL ECU (w/ Seat Memory)

C159480E06

  1. Disconnect the X10 and X11 power seat control ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    X11-5 (CANH) - X11-1 (CANL)
    GR - W
    Ignition switch off
    54 to 69 Ω
    X11-5 (CANH) - X10-1 (GND)
    GR - W-B
    Ignition switch off
    200 Ω or higher
    X11-1 (CANL) - X10-1 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    X11-5 (CANH) - X10-5 (+B)
    GR - L
    Ignition switch off
    6 kΩ or higher
    X11-1 (CANL) - X10-5 (+B)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK OUTER MIRROR CONTROL ECU (w/ Seat Memory)

C159485E03

  1. Disconnect the M7 and M8 outer mirror control ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    M8-1 (CAN) - M8-21 (CGND)
    LG - W
    Ignition switch off
    54 to 69 Ω
    M8-1 (CAN) - M7-9 (GND)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    M8-21 (CGND) - M7-9 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    M8-1 (CAN) - M7-3 (B)
    LG - R
    Ignition switch off
    6 kΩ or higher
    M8-21 (CGND) - M7-3 (B)
    W - R
    Ignition switch off
    6 kΩ or higher


CHECK MULTIPLEX TILT AND TELESCOPIC ECU (w/ Seat Memory)

C159486E03

  1. Disconnect the H57 multiplex tilt and telescopic ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H57-5 (CANH) - H57-14 (CANL)
    BE - W
    Ignition switch off
    54 to 69 Ω
    H57-5 (CANH) - H57-11 (GND)
    BE - W-B
    Ignition switch off
    200 Ω or higher
    H57-14 (CANL) - H57-11 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H57-5 (CANH) - H57-2 (+B)
    BE - V
    Ignition switch off
    6 kΩ or higher
    H57-14 (CANL) - H57-2 (+B)
    W - V
    Ignition switch off
    6 kΩ or higher


CHECK POWER STEERING ECU

C217238E05

  1. Disconnect the H38 ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H112-1 (CANH) - H112-2 (CANL)
    GR - W
    Ignition switch off
    54 to 69 Ω
    H112-1 (CANH) - H112-3(GND)
    GR - W-B
    Ignition switch off
    200 Ω or higher
    H112-2 (CANL) - H112-3 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H112-1 (CANH) - H19-16 (BAT)
    GR - P
    Ignition switch off
    6 kΩ or higher
    H112-2 (CANL) - H19-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK SUSPENSION CONTROL ECU (w/ Air Suspension)

E158723E03

  1. Disconnect the O17 and O18 suspension control ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    O18-30 (CANH) - O18-29 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    O18-30 (CANH) - O18-1 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    O18-29 (CANL) - O18-1 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    O18-30 (CANH) - O17-6 (B)
    B - SB
    Ignition switch off
    6 kΩ or higher
    O18-29 (CANL) - O17-6 (B)
    W - SB
    Ignition switch off
    6 kΩ or higher


CHECK POWER BACK DOOR ECU (w/ Power Back Door)

H100802E07

  1. Disconnect the O30 power back door ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    O30-6 (CANP) - O30-5 (CANN)
    B - W
    Ignition switch off
    54 to 69 Ω
    O30-6 (CANP) - O30-11 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    O30-5 (CANN) - O30-11 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    O30-6 (CANP) - O30-12 (B)
    B - L
    Ignition switch off
    6 kΩ or higher
    O30-5 (CANN) - O30-12 (B)
    W - L
    Ignition switch off
    6 kΩ or higher