CAN COMMUNICATION SYSTEM > TERMINALS OF ECU |
| DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
| JUNCTION CONNECTOR |
NO. 1 JUNCTION CONNECTOR

| *a | for Center Airbag Sensor Assembly | *b |
|
| *c | for DLC3 | *d | for Steering Angle Sensor |
| *e | for No. 2 Junction Connector | *f | for Main Body ECU (Cowl Side Junction Block LH) (V1 Bus) |
| *g | for Power Steering ECU Assembly | *h | for Brake Actuator Assembly (Skid Control ECU) |
| No. 1 Junction Connector | Wiring Color | Connect to |
| H115-1 (CANH) | BR | Center airbag sensor assembly |
| H115-12 (CANL) | W | |
| H115-2 (CANH) | SB |
|
| H115-13 (CANL) | W | |
| H115-3 (CANH) | V | DLC3 |
| H115-14 (CANL) | W | |
| H115-4 (CANH) | G | Steering angle sensor |
| H115-15 (CANL) | W | |
| H115-5 (CANH) | R | No. 2 junction connector |
| H115-16 (CANL) | W | |
| H115-6 (CANH) | L | Main body ECU (cowl side junction block LH) (V1 bus) |
| H115-17 (CANL) | W | |
| H115-7 (CANH) | GR | Power steering ECU assembly |
| H115-18 (CANL) | W | |
| H115-9 (CANH) | B | Brake actuator assembly (skid control ECU) |
| H115-20 (CANL) | W |
NO. 2 JUNCTION CONNECTOR

| *a | for Air Conditioning Amplifier Assembly | *b | for 4 Wheel Drive Control ECU (4WD Control ECU) (for 4WD) |
| *c | for ECM | *d | for No. 1 Junction Connector |
| *e | for Bus Buffer ECU (w/ Bus Buffer ECU) | *f | for Network Gateway ECU (V1 bus) (w/ Blind Spot Monitor System) |
| No. 2 Junction Connector | Wiring Color | Connect to |
| H110-1 (CANH) | B | Air conditioning amplifier assembly |
| H110-12 (CANL) | W | |
| H110-2 (CANH) | BE | 4 wheel drive control ECU (4WD control ECU)*1 |
| H110-13 (CANL) | W | |
| H110-3 (CANH) | GR | ECM |
| H110-14 (CANL) | W | |
| H110-4 (CANH) | R | No. 1 junction connector |
| H110-15 (CANL) | W | |
| H110-5 (CANH) | P | Bus buffer ECU*2 |
| H110-16 (CANL) | W | |
| H110-6 (CANH) | SB | Network gateway ECU (V1 bus)*3 |
| H110-17 (CANL) | W |
NO. 3 JUNCTION CONNECTOR

| *a | for Combination Meter Assembly (MS Bus) | *b | for Multiplex Tilt and Telescopic ECU (w/ Seat Memory) |
| *c | for Front Power Seat Switch LH (Power Seat Control ECU) (w/ Seat Memory) | *d |
|
| *e | for Outer Mirror Control ECU Assembly (w/ Seat Memory) | *f | for No. 5 Junction Connector (w/ Blind Spot Monitor System) |
| *g | for Network Gateway ECU (V2 Bus) (w/ Blind Spot Monitor System) | - | - |
| No. 3 Junction Connector | Wiring Color | Connect to |
| H122-1 (CANH) | Y | Combination meter assembly (MS bus) |
| H122-12 (CANL) | W | |
| H122-2 (CANH) | BE | Multiplex tilt and telescopic ECU*1 |
| H122-13 (CANL) | W | |
| H122-3 (CANH) | GR | Front power seat switch LH (power seat control ECU)*1 |
| H122-14 (CANL) | W | |
| H122-4 (CANH) | B |
|
| H122-15 (CANL) | W | |
| H122-5 (CANH) | LG | Outer mirror control ECU assembly*1 |
| H122-16 (CANL) | W | |
| H122-9 (CANH) | B | No. 5 junction connector*4 |
| H122-20 (CANL) | W | |
| H122-10 (CANH) | L | Network gateway ECU (V2 bus)*4 |
| H122-21 (CANL) | W |
NO. 4 JUNCTION CONNECTOR (FRONT OF THE VEHICLE) (w/ Power Back Door System or w/ Air Suspension System)

| *a | for Combination Meter Assembly (V1 Bus) | *b | for No. 1 Junction Connector |
| *c | for Main Body ECU (Cowl Side Junction Block LH) (MS Bus) | *d | for No. 3 Junction Connector (MS Bus) |
| No. 4 Junction Connector | Wiring Color | Connect to |
| O41-1 (CANH) | SB | Combination meter assembly (V1 bus) |
| O41-7 (CANL) | W | |
| O41-2 (CANH) | L | No. 1 junction connector |
| O41-8 (CANL) | W | |
| O41-5 (CANH) | B | Main body ECU (cowl side junction block LH) (MS bus) |
| O41-11 (CANL) | W | |
| O41-6 (CANH) | P | No. 3 junction connector (MS bus) |
| O41-12 (CANL) | W |
NO. 4 JUNCTION CONNECTOR (REAR OF THE VEHICLE) (w/ Power Back Door System or w/ Air Suspension System)

| *a | for Power Back Door Unit Assembly (Power Back Door ECU) (w/ Power Back Door System) | *b | for Suspension Control ECU (w/ Air Suspension System) |
| No. 4 Junction Connector | Wiring Color | Connect to |
| O42-1 (CANH) | B | Power back door unit assembly (power back door ECU)*1 |
| O42-7 (CANL) | W | |
| O42-6 (CANH) | B | Suspension control ECU*2 |
| O42-12 (CANL) | W |
NO. 5 JUNCTION CONNECTOR (w/ Blind Spot Monitor System)

| *a | for No. 3 Junction Connector (V2 Bus) | *b | for No. 6 Junction Connector |
| *c | for Blind Spot Monitor Sensor LH | - | - |
| No. 5 Junction Connector | Wiring Color | Connect to |
| O47-9 (CANH) | B | No. 3 junction connector (V2 bus) |
| O47-20 (CANL) | W | |
| O47-10 (CANH) | G | No. 6 junction connector |
| O47-21 (CANL) | W | |
| O47-11 (CANH) | BE | Blind spot monitor sensor LH |
| O47-22 (CANL) | W |
NO. 6 JUNCTION CONNECTOR (w/ Blind Spot Monitor System)

| *a | for No. 5 Junction Connector | *b | for Blind Spot Monitor Sensor RH |
| *c | for No. 7 Junction Connector | - | - |
| No. 6 Junction Connector | Wiring Color | Connect to |
| O48-9 (CANH) | G | No. 5 junction connector |
| O48-20 (CANL) | W | |
| O48-10 (CANH) | R | Blind spot monitor sensor RH |
| O48-21 (CANL) | W | |
| O48-11 (CANH) | L | No. 7 junction connector |
| O48-22 (CANL) | W |
![]() |
NO. 7 JUNCTION CONNECTOR (w/ Blind Spot Monitor System)
| *a | No. 6 Junction Connector |
| No. 7 Junction Connector | Wiring Color | Connect to |
| O49-3 (CANH) | L | No. 6 junction connector |
| O49-2 (CANL) | W |
| CHECK DLC3 |
![]() |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| H19-6 (CANH) - H19-14 (CANL) | V - W | Ignition switch off | 54 to 69 Ω |
| H19-6 (CANH) - H19-4 (CG) | V - W-B | Ignition switch off | 200 Ω or higher |
| H19-14 (CANL) - H19-4 (CG) | W - W-B | Ignition switch off | 200 Ω or higher |
| H19-6 (CANH) - H19-16 (BAT) | V - P | Ignition switch off | 6 kΩ or higher |
| H19-14 (CANL) - H19-16 (BAT) | W - P | Ignition switch off | 6 kΩ or higher |
| CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) |

Disconnect the A19 brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| A19-12 (CANH) - A19-13 (CANL) | B - W | Ignition switch off | 54 to 69 Ω |
| A19-12 (CANH) - A19-16 (GND1) | B - W-B | Ignition switch off | 200 Ω or higher |
| A19-13 (CANL) - A19-16 (GND1) | W - W-B | Ignition switch off | 200 Ω or higher |
| A19-12 (CANH) - A19-1 (+BM) | B - L | Ignition switch off | 6 kΩ or higher |
| A19-13 (CANL) - A19-1 (+BM) | W - L | Ignition switch off | 6 kΩ or higher |
| CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) |

| *A | for V1 Bus | *B | for MS Bus |
Disconnect the H2, DB and DD main body ECU (cowl side junction block LH) connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| H2-5 (CANH) - H2-6 (CANL) | L - W | Ignition switch off | 54 to 69 Ω |
| H2-5 (CANH) - DD-62 (GND1) | L - W-B | Ignition switch off | 200 Ω or higher |
| H2-6 (CANL) - DD-62 (GND1) | W - W-B | Ignition switch off | 200 Ω or higher |
| H2-5 (CANH) - DB-13 (BECU) | L - GR | Ignition switch off | 6 kΩ or higher |
| H2-6 (CANL) - DB-13 (BECU) | W - GR | Ignition switch off | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| H2-16 (CANP) - H2-15 (CANN) | B - W | Ignition switch off | 108 to 132 Ω |
| H2-16 (CANP) - DD-62 (GND1) | B - W-B | Ignition switch off | 200 Ω or higher |
| H2-15 (CANN) - DD-62 (GND1) | W - W-B | Ignition switch off | 200 Ω or higher |
| H2-16 (CANP) - DB-13 (BECU) | B - GR | Ignition switch off | 6 kΩ or higher |
| H2-15 (CANN) - DB-13 (BECU) | W - GR | Ignition switch off | 6 kΩ or higher |
| CHECK ECM |

Disconnect the A27 and D56 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| A27-10 (CANH) - A27-11 (CANL) | GR - W | Ignition switch off | 108 to 132 Ω |
| A27-10 (CANH) - D56-81 (E1) | GR - BR | Ignition switch off | 200 Ω or higher |
| A27-11 (CANL) - D56-81 (E1) | W - BR | Ignition switch off | 200 Ω or higher |
| A27-10 (CANH) - A27-1 (BATT) | GR - L | Ignition switch off | 6 kΩ or higher |
| A27-11 (CANL) - A27-1 (BATT) | W - L | Ignition switch off | 6 kΩ or higher |
| CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY |

Disconnect the H24 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| H24-11 (CANH) - H24-12 (CANL) | B - W | Ignition switch off | 54 to 69 Ω |
| H24-11 (CANH) - H24-14 (GND) | B - W-B | Ignition switch off | 200 Ω or higher |
| H24-12 (CANL) - H24-14 (GND) | W - W-B | Ignition switch off | 200 Ω or higher |
| H24-11 (CANH) - H24-21 (B) | B - R | Ignition switch off | 6 kΩ or higher |
| H24-12 (CANL) - H24-21 (B) | W - R | Ignition switch off | 6 kΩ or higher |
| CHECK CENTER AIRBAG SENSOR ASSEMBLY |

Disconnect the H56 center airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| H56-13 (CANH) - H56-22 (CANL) | BR - W | Ignition switch off | 54 to 69 Ω |
| H56-13 (CANH) - H56-25 (E1) | BR - W-B | Ignition switch off | 200 Ω or higher |
| H56-22 (CANL) - H56-25 (E1) | W - W-B | Ignition switch off | 200 Ω or higher |
| H56-13 (CANH) - H19-16 (BAT) | BR - P | Ignition switch off | 6 kΩ or higher |
| H56-22 (CANL) - H19-16 (BAT) | W - P | Ignition switch off | 6 kΩ or higher |
| CHECK COMBINATION METER ASSEMBLY |

| *A | for V1 Bus | *B | for MS Bus |
Disconnect the H37 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| H37-33 (CANH) - H37-34 (CANL) | SB - W | Ignition switch off | 108 to 132 Ω |
| H37-33 (CANH) - H37-40 (E1) | SB - W-B | Ignition switch off | 200 Ω or higher |
| H37-34 (CANL) - H37-40 (E1) | W - W-B | Ignition switch off | 200 Ω or higher |
| H37-33 (CANH) - H37-18 (B) | SB - LG | Ignition switch off | 6 kΩ or higher |
| H37-34 (CANL) - H37-18 (B) | W - LG | Ignition switch off | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| H37-22 (CANH) - H37-21 (CANL) | Y - W | Ignition switch off | 108 to 132 Ω |
| H37-22 (CANH) - H37-40 (E1) | Y - W-B | Ignition switch off | 200 Ω or higher |
| H37-21 (CANL) - H37-40 (E1) | W - W-B | Ignition switch off | 200 Ω or higher |
| H37-22 (CANH) - H37-18 (B) | Y - LG | Ignition switch off | 6 kΩ or higher |
| H37-21 (CANL) - H37-18 (B) | W - LG | Ignition switch off | 6 kΩ or higher |
| CHECK STEERING ANGLE SENSOR |

Disconnect the H6 steering angle sensor connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| H6-10 (CANH) - H6-9 (CANL) | G - W | Ignition switch off | 54 to 69 Ω |
| H6-10 (CANH) - H6-2 (ESS) | G - W-B | Ignition switch off | 200 Ω or higher |
| H6-9 (CANL) - H6-2 (ESS) | W - W-B | Ignition switch off | 200 Ω or higher |
| H6-10 (CANH) - H6-3 (BAT) | G - R | Ignition switch off | 6 kΩ or higher |
| H6-9 (CANL) - H6-3 (BAT) | W - R | Ignition switch off | 6 kΩ or higher |
| CHECK 4 WHEEL DRIVE CONTROL ECU (4WD CONTROL ECU) (for 4WD) |

Disconnect the A28 and A29 4 wheel drive control ECU (4WD control ECU) connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| A28-19 (CANH) - A28-20 (CANL) | BE - W | Ignition switch off | 54 to 69 Ω |
| A28-19 (CANH) - A29-4 (GND) | BE - W-B | Ignition switch off | 200 Ω or higher |
| A28-20 (CANL) - A29-4 (GND) | W - W-B | Ignition switch off | 200 Ω or higher |
| A28-19 (CANH) - H19-16 (BAT) | BE - P | Ignition switch off | 6 kΩ or higher |
| A28-20 (CANL) - H19-16 (BAT) | W - P | Ignition switch off | 6 kΩ or higher |
| CHECK BUS BUFFER ECU (w/ Bus Buffer ECU) |
![]() |
Disconnect the H66 bus buffer ECU connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| H66-3 (CAN+) - H66-2 (CAN-) | P - W | Ignition switch off | 54 to 69 Ω |
| CHECK FRONT POWER SEAT SWITCH LH (POWER SEAT CONTROL ECU) (w/ Seat Memory) |

Disconnect the X10 and X11 front power seat switch LH (power seat control ECU) connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| X11-5 (CANH) - X11-1 (CANL) | GR - W | Ignition switch off | 54 to 69 Ω |
| X11-5 (CANH) - X10-1 (GND) | GR - W-B | Ignition switch off | 200 Ω or higher |
| X11-1 (CANL) - X10-1 (GND) | W - W-B | Ignition switch off | 200 Ω or higher |
| X11-5 (CANH) - X10-5 (+B) | GR - L | Ignition switch off | 6 kΩ or higher |
| X11-1 (CANL) - X10-5 (+B) | W - L | Ignition switch off | 6 kΩ or higher |
| CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Seat Memory) |

Disconnect the M7 and M8 outer mirror control ECU assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| M8-1 (CAN) - M8-21 (CGND) | LG - W | Ignition switch off | 54 to 69 Ω |
| M8-1 (CAN) - M7-9 (GND) | LG - W-B | Ignition switch off | 200 Ω or higher |
| M8-21 (CGND) - M7-9 (GND) | W - W-B | Ignition switch off | 200 Ω or higher |
| M8-1 (CAN) - M7-3 (B) | LG - R | Ignition switch off | 6 kΩ or higher |
| M8-21 (CGND) - M7-3 (B) | W - R | Ignition switch off | 6 kΩ or higher |
| CHECK MULTIPLEX TILT AND TELESCOPIC ECU (w/ Seat Memory) |

Disconnect the H57 multiplex tilt and telescopic ECU connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| H57-5 (CANH) - H57-14 (CANL) | BE - W | Ignition switch off | 54 to 69 Ω |
| H57-5 (CANH) - H57-11 (GND) | BE - W-B | Ignition switch off | 200 Ω or higher |
| H57-14 (CANL) - H57-11 (GND) | W - W-B | Ignition switch off | 200 Ω or higher |
| H57-5 (CANH) - H57-2 (+B) | BE - V | Ignition switch off | 6 kΩ or higher |
| H57-14 (CANL) - H57-2 (+B) | W - V | Ignition switch off | 6 kΩ or higher |
| CHECK POWER STEERING ECU ASSEMBLY |

Disconnect the H112 power steering ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| H112-1 (CANH) - H112-2 (CANL) | GR - W | Ignition switch off | 54 to 69 Ω |
| H112-1 (CANH) - H112-3(GND) | GR - W-B | Ignition switch off | 200 Ω or higher |
| H112-2 (CANL) - H112-3 (GND) | W - W-B | Ignition switch off | 200 Ω or higher |
| H112-1 (CANH) - H19-16 (BAT) | GR - P | Ignition switch off | 6 kΩ or higher |
| H112-2 (CANL) - H19-16 (BAT) | W - P | Ignition switch off | 6 kΩ or higher |
| CHECK SUSPENSION CONTROL ECU (w/ Air Suspension System) |
w/ AVS:

Disconnect the O16 suspension control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| O16-7 (CANH) - O16-8 (CANL) | B - W | Ignition switch off | 54 to 69 Ω |
| O16-7 (CANH) - O16-5 (GND) | B - W-B | Ignition switch off | 200 Ω or higher |
| O16-8 (CANL) - O16-5 (GND) | W - W-B | Ignition switch off | 200 Ω or higher |
| O16-7 (CANH) - O16-3 (B) | B - SB | Ignition switch off | 6 kΩ or higher |
| O16-8 (CANL) - O16-3 (B) | W - SB | Ignition switch off | 6 kΩ or higher |
w/o AVS:

Disconnect the O19 suspension control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| O19-29 (CANH) - O19-28 (CANL) | B - W | Ignition switch off | 54 to 69 Ω |
| O19-29 (CANH) - O19-22 (GND) | B - W-B | Ignition switch off | 200 Ω or higher |
| O19-28 (CANL) - O19-22 (GND) | W - W-B | Ignition switch off | 200 Ω or higher |
| O19-29 (CANH) - O19-24 (B) | B - SB | Ignition switch off | 6 kΩ or higher |
| O19-28 (CANL) - O19-24 (B) | W - SB | Ignition switch off | 6 kΩ or higher |
| CHECK POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU) (w/ Power Back Door System) |

Disconnect the O30 power back door unit assembly (power back door ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| O30-6 (CANP) - O30-5 (CANN) | B - W | Ignition switch off | 54 to 69 Ω |
| O30-6 (CANP) - O30-11 (GND) | B - W-B | Ignition switch off | 200 Ω or higher |
| O30-5 (CANN) - O30-11 (GND) | W - W-B | Ignition switch off | 200 Ω or higher |
| O30-6 (CANP) - O30-12 (B) | B - L | Ignition switch off | 6 kΩ or higher |
| O30-5 (CANN) - O30-12 (B) | W - L | Ignition switch off | 6 kΩ or higher |
| CHECK NETWORK GATEWAY ECU (w/ Blind Spot Monitor System) |

| *A | for V1 Bus | *B | for V2 Bus |
Disconnect the H120 network gateway ECU connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| H120-16 (CA1H) - H120-15 (CA1L) | SB - W | Ignition switch off | 54 to 69 Ω |
| H120-16 (CA1H) - H120-4 (GND) | SB - W-B | Ignition switch off | 200 Ω or higher |
| H120-15 (CA1L) - H120-4 (GND) | W - W-B | Ignition switch off | 200 Ω or higher |
| H120-16 (CA1H) - H120-2 (BATT) | SB - L | Ignition switch off | 6 kΩ or higher |
| H120-15 (CA1L) - H120-2 (BATT) | W - L | Ignition switch off | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| H120-13 (CA2H) - H120-12 (CA2L) | L - W | Ignition switch off | 108 to 132 Ω |
| H120-13 (CA2H) - H120-4 (GND) | L - W-B | Ignition switch off | 200 Ω or higher |
| H120-12 (CA2L) - H120-4 (GND) | W - W-B | Ignition switch off | 200 Ω or higher |
| H120-13 (CA2H) - H120-2 (BATT) | L - L | Ignition switch off | 6 kΩ or higher |
| H120-12 (CA2L) - H120-2 (BATT) | W - L | Ignition switch off | 6 kΩ or higher |
| CHECK BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System) |

Disconnect the O46 blind spot monitor sensor LH connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| O46-8 (CA1P) - O46-4 (CA1N) | BE - W | Ignition switch off | 54 to 69 Ω |
| O46-8 (CA1P) - O46-1 (BLGD) | BE - W-B | Ignition switch off | 200 Ω or higher |
| O46-4 (CA1N) - O46-1 (BLGD) | W - W-B | Ignition switch off | 200 Ω or higher |
| O46-8 (CA1P) - H19-16 (BAT) | BE - P | Ignition switch off | 6 kΩ or higher |
| O46-4 (CA1N) - H19-16 (BAT) | W - P | Ignition switch off | 6 kΩ or higher |
| CHECK BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor System) |

Disconnect the P25 blind spot monitor sensor RH connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Switch Condition | Specified Condition |
| P25-8 (CA1P) - P25-4 (CA1N) | R - W | Ignition switch off | 54 to 69 Ω |
| P25-8 (CA1P) - P25-1 (BRGD) | R - W-B | Ignition switch off | 200 Ω or higher |
| P25-4 (CA1N) - P25-1 (BRGD) | W - W-B | Ignition switch off | 200 Ω or higher |
| P25-8 (CA1P) - H19-16 (BAT) | R - P | Ignition switch off | 6 kΩ or higher |
| P25-4 (CA1N) - H19-16 (BAT) | W - P | Ignition switch off | 6 kΩ or higher |