Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
    2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    3. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


JUNCTION CONNECTOR


  1. NO. 1 JUNCTION CONNECTOR


    C219227E62


    Text in Illustration 
    *a
    for Center Airbag Sensor Assembly
    *b
    1. for No. 4 Junction Connector (w/ Air Suspension System)
    2. for Combination Meter Assembly (V1 Bus) (w/o Air Suspension System)
    *c
    for DLC3
    *d
    for Steering Angle Sensor
    *e
    for No. 2 Junction Connector
    *f
    for Main Body ECU (Cowl Side Junction Block LH) (V1 Bus)
    *g
    for Power Steering ECU Assembly
    *h
    for Brake Actuator Assembly (Skid Control ECU)

    No. 1 Junction Connector
    Wiring Color
    Connect to
    H115-1 (CANH)
    BR
    Center airbag sensor assembly
    H115-12 (CANL)
    W
    H115-2 (CANH)
    SB
    1. No. 4 junction connector*1
    2. Combination meter assembly (V1 bus)*2
    H115-13 (CANL)
    W
    H115-3 (CANH)
    V
    DLC3
    H115-14 (CANL)
    W
    H115-4 (CANH)
    G
    Steering angle sensor
    H115-15 (CANL)
    W
    H115-5 (CANH)
    R
    No. 2 junction connector
    H115-16 (CANL)
    W
    H115-6 (CANH)
    L
    Main body ECU (cowl side junction block LH) (V1 bus)
    H115-17 (CANL)
    W
    H115-7 (CANH)
    GR
    Power steering ECU assembly
    H115-18 (CANL)
    W
    H115-9 (CANH)
    B
    Brake actuator assembly (skid control ECU)
    H115-20 (CANL)
    W
    1. *1: w/ Air Suspension System
    2. *2: w/o Air Suspension System



  2. NO. 2 JUNCTION CONNECTOR


    C219227E63


    Text in Illustration 
    *a
    for Air Conditioning Amplifier Assembly
    *b
    for 4 Wheel Drive Control ECU (4WD Control ECU) (for 4WD)
    *c
    for ECM
    *d
    for No. 1 Junction Connector
    *e
    for Bus Buffer ECU (w/ Bus Buffer ECU)
    *f
    for Network Gateway ECU (V1 bus) (w/ Blind Spot Monitor System)

    No. 2 Junction Connector
    Wiring Color
    Connect to
    H110-1 (CANH)
    B
    Air conditioning amplifier assembly
    H110-12 (CANL)
    W
    H110-2 (CANH)
    BE
    4 wheel drive control ECU (4WD control ECU)*1
    H110-13 (CANL)
    W
    H110-3 (CANH)
    GR
    ECM
    H110-14 (CANL)
    W
    H110-4 (CANH)
    R
    No. 1 junction connector
    H110-15 (CANL)
    W
    H110-5 (CANH)
    P
    Bus buffer ECU*2
    H110-16 (CANL)
    W
    H110-6 (CANH)
    SB
    Network gateway ECU (V1 bus)*3
    H110-17 (CANL)
    W
    1. *1: for 4WD
    2. *2: w/ Bus Buffer ECU
    3. *3: w/ Blind Spot Monitor System



  3. NO. 3 JUNCTION CONNECTOR


    C219227E89


    Text in Illustration 
    *a
    for Combination Meter Assembly (MS Bus)
    *b
    for Multiplex Tilt and Telescopic ECU (w/ Seat Memory)
    *c
    for Front Power Seat Switch LH (Power Seat Control ECU) (w/ Seat Memory)
    *d
    1. for No. 4 Junction Connector (w/ Power Back Door System)
    2. for Main Body ECU (Cowl Side Junction Block LH) (MS Bus) (w/o Power Back Door System)
    *e
    for Outer Mirror Control ECU Assembly (w/ Seat Memory)
    *f
    for No. 5 Junction Connector (w/ Blind Spot Monitor System)
    *g
    for Network Gateway ECU (V2 Bus) (w/ Blind Spot Monitor System)
    -
    -

    No. 3 Junction Connector
    Wiring Color
    Connect to
    H129-1 (CANH)
    Y
    Combination meter assembly (MS bus)
    H129-12 (CANL)
    W
    H129-2 (CANH)
    BE
    Multiplex tilt and telescopic ECU*1
    H129-13 (CANL)
    W
    H129-3 (CANH)
    GR
    Front power seat switch LH (power seat control ECU)*1
    H129-14 (CANL)
    W
    H129-4 (CANH)
    B
    1. No. 4 junction connector*2
    2. Main body ECU (cowl side junction block LH) (MS bus)*3
    H129-15 (CANL)
    W
    H129-5 (CANH)
    LG
    Outer mirror control ECU assembly*1
    H129-16 (CANL)
    W
    H129-9 (CANH)
    B
    No. 5 junction connector*4
    H129-20 (CANL)
    W
    H129-10 (CANH)
    L
    Network gateway ECU (V2 bus)*4
    H129-21 (CANL)
    W
    1. *1: w/ Seat Memory
    2. *2: w/ Power Back Door System
    3. *3: w/o Power Back Door System
    4. *4: w/ Blind Spot Monitor System



  4. NO. 4 JUNCTION CONNECTOR (FRONT OF THE VEHICLE) (w/ Power Back Door System or w/ Air Suspension System)


    C242665E01


    Text in Illustration 
    *a
    for Combination Meter Assembly (V1 Bus)
    *b
    for No. 1 Junction Connector
    *c
    for Main Body ECU (Cowl Side Junction Block LH) (MS Bus)
    *d
    for No. 3 Junction Connector (MS Bus)

    No. 4 Junction Connector
    Wiring Color
    Connect to
    O41-1 (CANH)
    SB
    Combination meter assembly (V1 bus)
    O41-7 (CANL)
    W
    O41-2 (CANH)
    L
    No. 1 junction connector
    O41-8 (CANL)
    W
    O41-5 (CANH)
    B
    Main body ECU (cowl side junction block LH) (MS bus)
    O41-11 (CANL)
    W
    O41-6 (CANH)
    P
    No. 3 junction connector (MS bus)
    O41-12 (CANL)
    W



  5. NO. 4 JUNCTION CONNECTOR (REAR OF THE VEHICLE) (w/ Power Back Door System or w/ Air Suspension System)


    C242665E02


    Text in Illustration 
    *a
    for Power Back Door Unit Assembly (Power Back Door ECU) (w/ Power Back Door System)
    *b
    for Suspension Control ECU (w/ Air Suspension System)

    No. 4 Junction Connector
    Wiring Color
    Connect to
    O42-1 (CANH)
    B
    Power back door unit assembly (power back door ECU)*1
    O42-7 (CANL)
    W
    O42-6 (CANH)
    B
    Suspension control ECU*2
    O42-12 (CANL)
    W
    1. *1: w/ Power Back Door System
    2. *2: w/ Air Suspension System



  6. NO. 5 JUNCTION CONNECTOR (w/ Blind Spot Monitor System)


    C219227E60


    Text in Illustration 
    *a
    for No. 3 Junction Connector (V2 Bus)
    *b
    for No. 6 Junction Connector
    *c
    for Blind Spot Monitor Sensor LH
    -
    -

    No. 5 Junction Connector
    Wiring Color
    Connect to
    O47-9 (CANH)
    B
    No. 3 junction connector (V2 bus)
    O47-20 (CANL)
    W
    O47-10 (CANH)
    G
    No. 6 junction connector
    O47-21 (CANL)
    W
    O47-11 (CANH)
    BE
    Blind spot monitor sensor LH
    O47-22 (CANL)
    W



  7. NO. 6 JUNCTION CONNECTOR (w/ Blind Spot Monitor System)


    C219227E61


    Text in Illustration 
    *a
    for No. 5 Junction Connector
    *b
    for Blind Spot Monitor Sensor RH
    *c
    for No. 7 Junction Connector
    -
    -

    No. 6 Junction Connector
    Wiring Color
    Connect to
    O48-9 (CANH)
    G
    No. 5 junction connector
    O48-20 (CANL)
    W
    O48-10 (CANH)
    R
    Blind spot monitor sensor RH
    O48-21 (CANL)
    W
    O48-11 (CANH)
    L
    No. 7 junction connector
    O48-22 (CANL)
    W



  8. C242676E01
  9. NO. 7 JUNCTION CONNECTOR (w/ Blind Spot Monitor System)
    Text in Illustration 
    *a
    No. 6 Junction Connector

    No. 7 Junction Connector
    Wiring Color
    Connect to
    O49-3 (CANH)
    L
    No. 6 junction connector
    O49-2 (CANL)
    W


CHECK DLC3
C201374E85
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-14 (CANL)
    V - W
    Ignition switch off
    54 to 69 Ω
    H19-6 (CANH) - H19-4 (CG)
    V - W-B
    Ignition switch off
    200 Ω or higher
    H19-14 (CANL) - H19-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H19-6 (CANH) - H19-16 (BAT)
    V - P
    Ignition switch off
    6 kΩ or higher
    H19-14 (CANL) - H19-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

C240485E03

  1. Disconnect the A19 brake actuator assembly (skid control ECU) connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A19-12 (CANH) - A19-13 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    A19-12 (CANH) - A19-16 (GND1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    A19-13 (CANL) - A19-16 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A19-12 (CANH) - A19-1 (+BM)
    B - L
    Ignition switch off
    6 kΩ or higher
    A19-13 (CANL) - A19-1 (+BM)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

C172609E11


Text in Illustration 
*A
for V1 Bus
*B
for MS Bus
  1. Disconnect the H2, DB and DD main body ECU (cowl side junction block LH) connectors.

  2. Measure the resistance according to the value(s) in the table below.

    for V1 Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H2-5 (CANH) - H2-6 (CANL)
    L - W
    Ignition switch off
    54 to 69 Ω
    H2-5 (CANH) - DD-62 (GND1)
    L - W-B
    Ignition switch off
    200 Ω or higher
    H2-6 (CANL) - DD-62 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H2-5 (CANH) - DB-13 (BECU)
    L - GR
    Ignition switch off
    6 kΩ or higher
    H2-6 (CANL) - DB-13 (BECU)
    W - GR
    Ignition switch off
    6 kΩ or higher

    for MS Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    B - W
    Ignition switch off
    108 to 132 Ω
    H2-16 (CANP) - DD-62 (GND1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    H2-15 (CANN) - DD-62 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H2-16 (CANP) - DB-13 (BECU)
    B - GR
    Ignition switch off
    6 kΩ or higher
    H2-15 (CANN) - DB-13 (BECU)
    W - GR
    Ignition switch off
    6 kΩ or higher


CHECK ECM

C159489E26

  1. Disconnect the A27 and D56 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A27-10 (CANH) - A27-11 (CANL)
    GR - W
    Ignition switch off
    108 to 132 Ω
    A27-10 (CANH) - D56-81 (E1)
    GR - BR
    Ignition switch off
    200 Ω or higher
    A27-11 (CANL) - D56-81 (E1)
    W - BR
    Ignition switch off
    200 Ω or higher
    A27-10 (CANH) - A27-1 (BATT)
    GR - L
    Ignition switch off
    6 kΩ or higher
    A27-11 (CANL) - A27-1 (BATT)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

C159478E06

  1. Disconnect the H24 air conditioning amplifier assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H24-11 (CANH) - H24-12 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    H24-11 (CANH) - H24-14 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    H24-12 (CANL) - H24-14 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H24-11 (CANH) - H24-21 (B)
    B - R
    Ignition switch off
    6 kΩ or higher
    H24-12 (CANL) - H24-21 (B)
    W - R
    Ignition switch off
    6 kΩ or higher


CHECK CENTER AIRBAG SENSOR ASSEMBLY

C162022E04

  1. Disconnect the H56 center airbag sensor assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H56-13 (CANH) - H56-22 (CANL)
    BR - W
    Ignition switch off
    54 to 69 Ω
    H56-13 (CANH) - H56-25 (E1)
    BR - W-B
    Ignition switch off
    200 Ω or higher
    H56-22 (CANL) - H56-25 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H56-13 (CANH) - H19-16 (BAT)
    BR - P
    Ignition switch off
    6 kΩ or higher
    H56-22 (CANL) - H19-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK COMBINATION METER ASSEMBLY

C159488E08


Text in Illustration 
*A
for V1 Bus
*B
for MS Bus
  1. Disconnect the H37 combination meter assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    for V1 Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H37-33 (CANH) - H37-34 (CANL)
    SB - W
    Ignition switch off
    108 to 132 Ω
    H37-33 (CANH) - H37-40 (E1)
    SB - W-B
    Ignition switch off
    200 Ω or higher
    H37-34 (CANL) - H37-40 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H37-33 (CANH) - H37-18 (B)
    SB - LG
    Ignition switch off
    6 kΩ or higher
    H37-34 (CANL) - H37-18 (B)
    W - LG
    Ignition switch off
    6 kΩ or higher

    for MS Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H37-22 (CANH) - H37-21 (CANL)
    Y - W
    Ignition switch off
    108 to 132 Ω
    H37-22 (CANH) - H37-40 (E1)
    Y - W-B
    Ignition switch off
    200 Ω or higher
    H37-21 (CANL) - H37-40 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H37-22 (CANH) - H37-18 (B)
    Y - LG
    Ignition switch off
    6 kΩ or higher
    H37-21 (CANL) - H37-18 (B)
    W - LG
    Ignition switch off
    6 kΩ or higher


CHECK STEERING ANGLE SENSOR

C159491E04

  1. Disconnect the H6 steering angle sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H6-10 (CANH) - H6-9 (CANL)
    G - W
    Ignition switch off
    54 to 69 Ω
    H6-10 (CANH) - H6-2 (ESS)
    G - W-B
    Ignition switch off
    200 Ω or higher
    H6-9 (CANL) - H6-2 (ESS)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H6-10 (CANH) - H6-3 (BAT)
    G - R
    Ignition switch off
    6 kΩ or higher
    H6-9 (CANL) - H6-3 (BAT)
    W - R
    Ignition switch off
    6 kΩ or higher


CHECK 4 WHEEL DRIVE CONTROL ECU (4WD CONTROL ECU) (for 4WD)

C159479E09

  1. Disconnect the A28 and A29 4 wheel drive control ECU (4WD control ECU) connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A28-19 (CANH) - A28-20 (CANL)
    BE - W
    Ignition switch off
    54 to 69 Ω
    A28-19 (CANH) - A29-4 (GND)
    BE - W-B
    Ignition switch off
    200 Ω or higher
    A28-20 (CANL) - A29-4 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A28-19 (CANH) - H19-16 (BAT)
    BE - P
    Ignition switch off
    6 kΩ or higher
    A28-20 (CANL) - H19-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK BUS BUFFER ECU (w/ Bus Buffer ECU)
C242858E03
  1. Disconnect the H66 bus buffer ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H66-3 (CAN+) - H66-2 (CAN-)
    P - W
    Ignition switch off
    54 to 69 Ω


CHECK FRONT POWER SEAT SWITCH LH (POWER SEAT CONTROL ECU) (w/ Seat Memory)

C159480E08

  1. Disconnect the X10 and X11 front power seat switch LH (power seat control ECU) connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    X11-5 (CANH) - X11-1 (CANL)
    GR - W
    Ignition switch off
    54 to 69 Ω
    X11-5 (CANH) - X10-1 (GND)
    GR - W-B
    Ignition switch off
    200 Ω or higher
    X11-1 (CANL) - X10-1 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    X11-5 (CANH) - X10-5 (+B)
    GR - L
    Ignition switch off
    6 kΩ or higher
    X11-1 (CANL) - X10-5 (+B)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Seat Memory)

C159485E04

  1. Disconnect the M7 and M8 outer mirror control ECU assembly connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    M8-1 (CAN) - M8-21 (CGND)
    LG - W
    Ignition switch off
    54 to 69 Ω
    M8-1 (CAN) - M7-9 (GND)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    M8-21 (CGND) - M7-9 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    M8-1 (CAN) - M7-3 (B)
    LG - R
    Ignition switch off
    6 kΩ or higher
    M8-21 (CGND) - M7-3 (B)
    W - R
    Ignition switch off
    6 kΩ or higher


CHECK MULTIPLEX TILT AND TELESCOPIC ECU (w/ Seat Memory)

C159486E04

  1. Disconnect the H57 multiplex tilt and telescopic ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H57-5 (CANH) - H57-14 (CANL)
    BE - W
    Ignition switch off
    54 to 69 Ω
    H57-5 (CANH) - H57-11 (GND)
    BE - W-B
    Ignition switch off
    200 Ω or higher
    H57-14 (CANL) - H57-11 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H57-5 (CANH) - H57-2 (+B)
    BE - V
    Ignition switch off
    6 kΩ or higher
    H57-14 (CANL) - H57-2 (+B)
    W - V
    Ignition switch off
    6 kΩ or higher


CHECK POWER STEERING ECU ASSEMBLY

C217238E08

  1. Disconnect the H112 power steering ECU assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H112-1 (CANH) - H112-2 (CANL)
    GR - W
    Ignition switch off
    54 to 69 Ω
    H112-1 (CANH) - H112-3(GND)
    GR - W-B
    Ignition switch off
    200 Ω or higher
    H112-2 (CANL) - H112-3 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H112-1 (CANH) - H19-16 (BAT)
    GR - P
    Ignition switch off
    6 kΩ or higher
    H112-2 (CANL) - H19-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK SUSPENSION CONTROL ECU (w/ Air Suspension System)


  1. w/ AVS:


    E158723E05


    1. Disconnect the O16 suspension control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Switch Condition
      Specified Condition
      O16-7 (CANH) - O16-8 (CANL)
      B - W
      Ignition switch off
      54 to 69 Ω
      O16-7 (CANH) - O16-5 (GND)
      B - W-B
      Ignition switch off
      200 Ω or higher
      O16-8 (CANL) - O16-5 (GND)
      W - W-B
      Ignition switch off
      200 Ω or higher
      O16-7 (CANH) - O16-3 (B)
      B - SB
      Ignition switch off
      6 kΩ or higher
      O16-8 (CANL) - O16-3 (B)
      W - SB
      Ignition switch off
      6 kΩ or higher



  2. w/o AVS:


    E158724E04


    1. Disconnect the O19 suspension control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Switch Condition
      Specified Condition
      O19-29 (CANH) - O19-28 (CANL)
      B - W
      Ignition switch off
      54 to 69 Ω
      O19-29 (CANH) - O19-22 (GND)
      B - W-B
      Ignition switch off
      200 Ω or higher
      O19-28 (CANL) - O19-22 (GND)
      W - W-B
      Ignition switch off
      200 Ω or higher
      O19-29 (CANH) - O19-24 (B)
      B - SB
      Ignition switch off
      6 kΩ or higher
      O19-28 (CANL) - O19-24 (B)
      W - SB
      Ignition switch off
      6 kΩ or higher


CHECK POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU) (w/ Power Back Door System)

H100802E28

  1. Disconnect the O30 power back door unit assembly (power back door ECU) connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    O30-6 (CANP) - O30-5 (CANN)
    B - W
    Ignition switch off
    54 to 69 Ω
    O30-6 (CANP) - O30-11 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    O30-5 (CANN) - O30-11 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    O30-6 (CANP) - O30-12 (B)
    B - L
    Ignition switch off
    6 kΩ or higher
    O30-5 (CANN) - O30-12 (B)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK NETWORK GATEWAY ECU (w/ Blind Spot Monitor System)

C242684E01


Text in Illustration 
*A
for V1 Bus
*B
for V2 Bus
  1. Disconnect the H120 network gateway ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    for V1 Bus  
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H120-16 (CA1H) - H120-15 (CA1L)
    SB - W
    Ignition switch off
    54 to 69 Ω
    H120-16 (CA1H) - H120-4 (GND)
    SB - W-B
    Ignition switch off
    200 Ω or higher
    H120-15 (CA1L) - H120-4 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H120-16 (CA1H) - H120-2 (BATT)
    SB - L
    Ignition switch off
    6 kΩ or higher
    H120-15 (CA1L) - H120-2 (BATT)
    W - L
    Ignition switch off
    6 kΩ or higher

    for V2 Bus  
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H120-13 (CA2H) - H120-12 (CA2L)
    L - W
    Ignition switch off
    108 to 132 Ω
    H120-13 (CA2H) - H120-4 (GND)
    L - W-B
    Ignition switch off
    200 Ω or higher
    H120-12 (CA2L) - H120-4 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H120-13 (CA2H) - H120-2 (BATT)
    L - L
    Ignition switch off
    6 kΩ or higher
    H120-12 (CA2L) - H120-2 (BATT)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)

C242685E01

  1. Disconnect the O46 blind spot monitor sensor LH connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    O46-8 (CA1P) - O46-4 (CA1N)
    BE - W
    Ignition switch off
    54 to 69 Ω
    O46-8 (CA1P) - O46-1 (BLGD)
    BE - W-B
    Ignition switch off
    200 Ω or higher
    O46-4 (CA1N) - O46-1 (BLGD)
    W - W-B
    Ignition switch off
    200 Ω or higher
    O46-8 (CA1P) - H19-16 (BAT)
    BE - P
    Ignition switch off
    6 kΩ or higher
    O46-4 (CA1N) - H19-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher


CHECK BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor System)

C242685E02

  1. Disconnect the P25 blind spot monitor sensor RH connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    P25-8 (CA1P) - P25-4 (CA1N)
    R - W
    Ignition switch off
    54 to 69 Ω
    P25-8 (CA1P) - P25-1 (BRGD)
    R - W-B
    Ignition switch off
    200 Ω or higher
    P25-4 (CA1N) - P25-1 (BRGD)
    W - W-B
    Ignition switch off
    200 Ω or higher
    P25-8 (CA1P) - H19-16 (BAT)
    R - P
    Ignition switch off
    6 kΩ or higher
    P25-4 (CA1N) - H19-16 (BAT)
    W - P
    Ignition switch off
    6 kΩ or higher