Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > DIAGNOSIS SYSTEM

for Preparation Click here



BUS CHECK (COMMUNICATION MALFUNCTION ECU)

HINT:
Only CAN communication system DTCs for each ECU can be displayed on the intelligent tester.



    C128170
  1. Select "Bus Check" from the "System Select" screen on the intelligent tester.



  2. C128171
  3. Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".



  4. C128172
  5. Select the system of the DTC to be checked and select "Details".



  6. C128173
  7. CAN communication system DTCs are displayed.


BUS CHECK (COMMUNICATION BUS CHECK)

HINT:
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the intelligent tester.



    C128171
  1. Select "Communication Bus Check" from the "Bus Check" screen.



  2. C197126
  3. The screen displays the ECUs and sensors that are properly connected to the CAN communication system.

    HINT:
    1. If any properly connected ECUs or sensors are not displayed, there is a communication stop in the system (Click here).

    2. C197127
      The default item displayed in the combo box is "ALL". When checking the ECUs (sensors) connected to each bus, pull down the combo box and select the bus to be checked from the drop down list. The drop down list displays "ALL", "V Bus", and the names of the remaining buses.
      Combo Box
      Display Content
      ALL
      All ECUs (sensors) connected to the CAN bus
      V Bus
      ECUs (sensors) connected to the V bus
      Bus Name
      ECUs (sensors) connected to the selected bus
    3. The connection status (shown below) is indicated by the background color displayed behind the system name.
      ECU (Sensor) on V Bus
      Background Color
      Connection Status
      White
      Detected normally
      Yellow
      Could not be detected in the past, but is currently detected
      Red
      Detected in the past, but cannot be detected now
      Not displayed
      Has never been detected
      ECU (Sensor) with no Data Monitor History
      Background Color
      Connection Status
      White
      Detected normally
      Yellow
      Could not be detected in the past, but is currently detected
      Red
      Detected in the past, but cannot be detected now
      Not displayed
      Has never been detected
      ECU (Sensor) with no Data Monitor History
      Background Color
      Connection Status
      White
      Detected normally
      Yellow
      Could not be detected in the past, but is currently detected
      Red
      Detected in the past, but cannot be detected now
      Red
      Has never been detected but has connection history
      Not displayed
      Has never been detected and has no connection history



  4. C128179
  5. "There is no system connected to the communication bus" is displayed if there are no ECUs or sensors connected to the CAN bus.


CHECK INSTALLED SYSTEMS (ECUS AND SENSORS) THAT ADOPT CAN COMMUNICATION
  1. Systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle optional settings. Check which systems (ECUs and sensors) are installed on the vehicle.

    ECU/Sensor Name
    Installed to
    Power steering ECU
    All vehicles
    Skid control ECU
    All vehicles
    Air conditioning amplifier
    All vehicles
    ECM
    All vehicles
    Main body ECU
    All vehicles
    Combination meter ECU
    All vehicles
    Center airbag sensor assembly
    All vehicles
    Steering angle sensor
    All vehicles
    Bus buffer ECU
    Vehicles with Bus Buffer ECU
    4WD control ECU
    Vehicles with 4WD
    Power seat control ECU
    Vehicles with Front Power Seat Control System (with Seat Memory)
    Outer mirror control ECU
    Vehicles with Front Power Seat Control System (with Seat Memory)
    Multiplex tilt and telescopic ECU
    Vehicles with Front Power Seat Control System (with Seat Memory)
    Air suspension ECU
    Vehicles with Air Suspension
    Power back door ECU
    Vehicles with Power Back Door


DTC TABLE BY ECU

HINT:
  1. In the CAN communication system, CAN communication system DTCs output by the ECU can be displayed by using the intelligent tester.
  2. If CAN communication system DTCs are output, the trouble cannot be determined solely from the DTCs. Perform troubleshooting according to "How to Proceed with Troubleshooting" (Click here).

  1. MULTIPLEX TILT AND TELESCOPIC ECU
    For vehicles with seat memory only.

    HINT:
    DTC communication uses the CAN communication system.

    DTC Code
    Detection Item
    B2621
    Communication Interruption
    B2624
    Vehicles Speed Malfunction

  2. MAIN BODY ECU

    HINT:
    DTC communication uses the CAN communication system.

    DTC Code
    Detection Item
    U1002
    Lost Communication with Gateway Module
    U0199
    Lost Communication with "Door Control Module A"
    U0208
    Lost Communication with "Seat Control Module A"
    U1115
    Lost Communication with Tilt and Telescopic Module
    U0230
    Lost Communication with Rear Gate Module

  3. SKID CONTROL ECU

    HINT:
    DTC communication uses the CAN communication system.

    DTC Code
    Detection Item
    U0073
    Control Module Communication Bus OFF
    U0100
    Lost Communication with ECM/PCM "A"
    U0114
    Lost Communication with 4-Wheel Drive Clutch Control Module
    U0123
    Lost Communication with Yaw Rate Sensor Module
    U0124
    Deceleration Sensor Communication Circuit Malfunction
    U0126
    Lost Communication with Steering Angle Sensor Module

  4. COMBINATION METER ECU

    HINT:
    DTC communication uses the CAN communication system.

    DTC Code
    Detection Item
    U0100
    Lost Communication with ECM/PCM "A"
    U0129
    Lost Communication with Brake System Control Module

  5. AIR CONDITIONING AMPLIFIER

    HINT:
    DTC communication uses the CAN communication system.

    DTC Code
    Detection Item
    B1499
    Multiplex Communication Circuit

  6. SUSPENSION CONTROL ECU
    For Vehicles with air suspension only.

    HINT:
    DTC communication uses the CAN communication system.

    DTC Code
    Detection Item
    U0100
    Lost Communication with ECM/PCM "A"
    U0122
    Lost Communication with Vehicle Dynamics Control Module
    U0124
    Deceleration Sensor Communication Circuit Malfunction
    U0126
    Lost Communication with Steering Angle Sensor Module
    U0140
    Lost Communication with Main Body ECU

  7. POWER STEERING ECU

    HINT:
    DTC communication uses the CAN communication system.

    DTC Code
    Detection Item
    U0073
    Control Module Communication Bus Off

  8. ECM

    HINT:
    The ECM is connected to the CAN communication system but CAN communication DTCs are not output.

  9. STEERING ANGLE SENSOR

    HINT:
    The steering angle sensor is connected to the CAN communication system but CAN communication DTCs are not output.

  10. CENTER AIRBAG SENSOR

    HINT:
    The center airbag sensor is connected to the CAN communication system but CAN communication DTCs are not output.

  11. POWER BACK DOOR ECU
    For vehicles with power back door only.

    HINT:
    The power back door ECU is connected to the CAN communication system but CAN communication DTCs are not output.

  12. BUS BUFFER ECU
    For vehicles with bus buffer ECU only.

    HINT:
    The bus buffer ECU is connected to the CAN communication system but CAN communication DTCs are not output.

  13. 4WD CONTROL ECU
    For vehicles with 4WD only.

    HINT:
    The 4WD control ECU is connected to the CAN communication system but CAN communication DTCs are not output.

  14. POWER SEAT CONTROL ECU
    For vehicles with seat memory only.

    HINT:
    The power seat control ECU is connected to the CAN communication system but CAN communication DTCs are not output.

  15. OUTER MIRROR CONTROL ECU
    For vehicles with seat memory only.

    HINT:
    The outer mirror control ECU is connected to the CAN communication system but CAN communication DTCs are not output.


DTC COMBINATION TABLE

Output from
Output DTC
Detection Item
Detected Communication Stop Mode
MS Bus
Power Seat Control ECU Communication Stop Mode
Outer Mirror Control ECU Communication Stop Mode
Multiplex Tilt and Telescopic ECU Communication Stop Mode
Power Back Door ECU Communication Stop Mode
Main Body ECU Communication Stop Mode
Multiplex Tilt and Telescopic ECU
B2621
Communication Interruption
○
X
○*1
X
○
B2624
Vehicles Speed Malfunction
X
X
○*1
X
○
Main Body ECU
U0208
Lost Communication with "Seat Control Module A"
○
X
X
X
○*1
U0199
Lost Communication with "Door Control Module A"
X
○
X
X
○*1
U1115
Lost Communication with Tilt and Telescopic Module
X
X
○
X
○*1
U1002
Lost Communication with Gateway Module
X
X
X
X
○*1
U0230
Lost Communication with Rear Gate Module
X
X
X
○
○*1
Skid Control ECU
U0073
Control Module Communication Bus OFF
-
-
-
-
-
U0100
Lost Communication with ECM/PCM "A"
-
-
-
-
-
U0114
Lost Communication with 4-Wheel Drive Clutch Control Module
-
-
-
-
-
U0123
Lost Communication with Yaw Rate Sensor Module
-
-
-
-
-
U0124
Deceleration Sensor Communication Circuit Malfunction
-
-
-
-
-
U0126
Lost Communication with Steering Angle Sensor Module
-
-
-
-
-
Combination Meter ECU
U0100
Lost Communication with ECM/PCM "A"
-
-
-
-
-
U0129
Lost Communication with Brake System Control Module
-
-
-
-
-
Air Conditioning Amplifier
B1499
Multiplex Communication Circuit
-
-
-
-
-
Power Steering ECU
U0073
Control Module Communication Bus Off
-
-
-
-
-
Suspension Control ECU*2
U0100
Lost Communication with ECM/PCM "A"
-
-
-
-
-
U0122
Lost Communication with Vehicle Dynamics Control Module
-
-
-
-
-
U0124
Deceleration Sensor Communication Circuit Malfunction
-
-
-
-
-
U0126
Lost Communication with Steering Angle Sensor Module
-
-
-
-
-
U0140
Lost Communication with Main Body ECU
-
-
-
-
-

HINT:
  1. ○: Stored.
  2. X: When one side of branch wire is open, storage may occur.
  3. *1: DTC may not be output when the CAN communication system malfunctions.
  4. *2: w/ Air Suspension


Output from
Output DTC
Detection Item
Detected Communication Stop Mode
V1 Bus
Main Body ECU Communication Stop Mode
ECM Communication Stop Mode
Bus Buffer ECU Communication Stop Mode
Skid Control ECU Communication Stop Mode
Steering Angle Sensor Communication Stop Mode
Combination Meter ECU Communication Stop Mode
Multiplex Tilt and Telescopic ECU
B2621
Communication Interruption
-
-
-
-
-
-
B2624
Vehicles Speed Malfunction
○
X
X
X
X
○
Main Body ECU
U0208
Lost Communication with "Seat Control Module A"
-
-
-
-
-
-
U0199
Lost Communication with "Door Control Module A"
-
-
-
-
-
-
U1115
Lost Communication with Tilt and Telescopic Module
-
-
-
-
-
-
U1002
Lost Communication with Gateway Module
-
-
-
-
-
-
U0230
Lost Communication with Rear Gate Module
-
-
-
-
-
-
Skid Control ECU
U0073
Control Module Communication Bus OFF
X
X
X
○*1
X
X
U0100
Lost Communication with ECM/PCM "A"
X
○
X
○*1
X
X
U0114
Lost Communication with 4-Wheel Drive Clutch Control Module
X
X
X
○*1
X
X
U0123
Lost Communication with Yaw Rate Sensor Module
X
X
X
○*1
X
X
U0124
Deceleration Sensor Communication Circuit Malfunction
X
X
X
○*1
X
X
U0126
Lost Communication with Steering Angle Sensor Module
X
X
X
○*1
○
X
Combination Meter ECU
U0100
Lost Communication with ECM/PCM "A"
X
○
X
X
X
○*1
U0129
Lost Communication with Brake System Control Module
X
X
X
○
X
○*1
Air Conditioning Amplifier
B1499
Multiplex Communication Circuit
X
○
X
X
X
○
Power Steering ECU
U0073
Control Module Communication Bus Off
X
○
X
○
○
X
Suspension Control ECU*2
U0100
Lost Communication with ECM/PCM "A"
X
○
X
X
X
X
U0122
Lost Communication with Vehicle Dynamics Control Module
X
X
X
○
X
X
U0124
Deceleration Sensor Communication Circuit Malfunction
X
X
X
○
X
X
U0126
Lost Communication with Steering Angle Sensor Module
X
X
X
X
○
X
U0140
Lost Communication with Main Body ECU
X
X
X
X
X
X

HINT:
  1. ○: Stored.
  2. X: When one side of branch wire is open, storage may occur.
  3. *1: DTC may not be output when the CAN communication system malfunctions.
  4. *2: w/ Air Suspension


Output from
Output DTC
Detection Item
Detected Communication Stop Mode
V1 Bus
Center Airbag Sensor Communication Stop Mode
Air Conditioning Amplifier Communication Stop Mode
4WD Control ECU Communication Stop Mode
Suspension Control ECU Communication Stop Mode
Power Steering ECU Communication Stop Mode
Multiplex Tilt and Telescopic ECU
B2621
Communication Interruption
-
-
-
-
-
B2624
Vehicles Speed Malfunction
X
X
X
X
X
Main Body ECU
U0208
Lost Communication with "Seat Control Module A"
-
-
-
-
-
U0199
Lost Communication with "Door Control Module A"
-
-
-
-
-
U1115
Lost Communication with Tilt and Telescopic Module
-
-
-
-
-
U1002
Lost Communication with Gateway Module
-
-
-
-
-
U0230
Lost Communication with Rear Gate Module
-
-
-
-
-
Skid Control ECU
U0073
Control Module Communication Bus OFF
X
X
X
X
X
U0100
Lost Communication with ECM/PCM "A"
X
X
X
X
X
U0114
Lost Communication with 4-Wheel Drive Clutch Control Module
X
X
○
X
X
U0123
Lost Communication with Yaw Rate Sensor Module
X
X
X
X
X
U0124
Deceleration Sensor Communication Circuit Malfunction
X
X
X
X
X
U0126
Lost Communication with Steering Angle Sensor Module
X
X
X
X
X
Combination Meter ECU
U0100
Lost Communication with ECM/PCM "A"
X
X
X
X
X
U0129
Lost Communication with Brake System Control Module
X
X
X
X
X
Air Conditioning Amplifier
B1499
Multiplex Communication Circuit
X
○*1
X
X
X
Power Steering ECU
U0073
Control Module Communication Bus Off
X
X
X
X
○*1
Suspension Control ECU*2
U0100
Lost Communication with ECM/PCM "A"
X
X
X
○*1
X
U0122
Lost Communication with Vehicle Dynamics Control Module
X
X
X
○*1
X
U0124
Deceleration Sensor Communication Circuit Malfunction
X
X
X
○*1
X
U0126
Lost Communication with Steering Angle Sensor Module
X
X
X
○*1
X
U0140
Lost Communication with Main Body ECU
X
X
X
○*1
X

HINT:
  1. ○: Stored.
  2. X: When one side of branch wire is open, storage may occur.
  3. *1: DTC may not be output when the CAN communication system malfunctions.
  4. *2: w/ Air Suspension