CAN COMMUNICATION SYSTEM > FAIL-SAFE CHART |
| FAIL-SAFE FUNCTION |
When communication fails in any of the main wires (communication lines) due to a short circuit or other causes, the fail-safe function, which is specified for each system, operates to prevent the system from malfunctioning.
The table below shows the effects on each system when communication is impossible. For further details, refer to each system.
| Function | Behavior during CAN Failure | |||
| Vehicle Behavior | Indicator and Buzzer | Diagnostic Trouble Code | |
| VFC control (Changes the power steering fluid flow according to the state of the vehicle using the vehicle speed, engine speed, steering angle and towing information.) |
| Alternative control (The steering angle, vehicle speed and engine speed are fixed.) | PPS indicator light turns on | U0073 |
| Air conditioning control (Performs engine-linked control based on sensor information and controls the air conditioning and panel.) |
| Maintains previous values. | Nothing | Nothing |
| Power back door operation condition (Prohibit PBD function according to vehicle condition (IG, shift position P, vehicle speed, remote start, lock position) |
| PBD does not work. (Warn with buzzer when operation request is received.) | Buzzer | Nothing |
| Power back door operation request (Start PBD operation by receiving request trigger from operation switch, wireless switch) |
| PBD does not work. | Nothing | Nothing |
| Power back door operation status output (Output hazard ON request and door status during PBD working) |
| Indicator in meter is not ON when PBD is open. Hazard is not ON when PBD is operated. | Nothing | Nothing |
| Driver side seat memory system (Memorizes and recalls the driver side seat, steering wheel and outside mirror positions.) |
| Position memorization and recall cannot be performed. The tilt and telescopic system does not operate. | Nothing | Nothing |
| 2WD-4WD switching limitation (Switching between 2WD and 4WD is prohibited when the vehicle speed is outside the acceptable range.) |
| Switching between 2WD and 4WD is prohibited. | Indicator light blinks | Nothing |
| High-Low switching limitation (Prohibits High-Low switching when the vehicle speed or engine speed is outside the acceptable range or the A/T is not in N during the A/T status check.) |
| High-Low switching is prohibited. | Indicator light blinks | Nothing |
| Center differential lock switching control (Center differential lock switching is prohibited when there is a vehicle speed violation or large difference in wheel speeds.) |
| Center differential lock switching is prohibited. | Indicator light blinks | Nothing |
| L4F switching control (Switching to L4F is prohibited and the operation is performed with L4L when VSC is malfunctioning.) |
| L4F switching is prohibited | Indicator light blinks | Nothing |
| Control performed during low temperatures (Changes the value of the electric current applied to the ACT according to the temperature.) |
| Changes to the temperature used for ACT temperature correction control calculations. | Indicator light blinks | Nothing |
| Specialized control during wheel speed failure (When there is a wheel speed failure, switching is permitted only when specified conditions are met (the wheel speed malfunction is 1 wheel or more and 3 wheels or less, the brake is applied, the engine speed is low, and all normal wheel speeds are low.)) |
| If the wheel speed malfunction is 1 wheel or more and 3 wheels or less, only when the wheel speed failure specified conditions are met, switching is permitted. When 4 wheels are malfunctioning, switching is prohibited (the wheel speed failure specialized control does not operate). | Indicator light blinks | Nothing |
| Vehicle speed threshold limitation (Determines whether the temperature is low or normal and changes the vehicle speed at which shifting from to 2 to 4 is prohibited.) |
| Uses the threshold value for low temperatures. | Nothing | Nothing |
| Indicator and buzzer signal output (Outputs a signal indicating the state of the indicators and buzzers, which represent the actuator position and switching status.) |
| The signal cannot be transmitted. Therefore, the signal is not updated. | Nothing | Nothing |
| Cruise control cancel signal output (Outputs a cruise control cancel signal when center differential switching is not completed even though 5 seconds or more have elapsed from the start of switching.) |
| The signal cannot be transmitted. Therefore, the signal is not updated. | Nothing | Nothing |
| L4 state signal output (Outputs a signal when switching to the L4 position is finished.) |
| The signal cannot be transmitted. Therefore, the signal is not updated. | Nothing | Nothing |
| 4WD state signal output (The ADDSW state is output.) |
| The signal cannot be transmitted. Therefore, the signal is not updated. | Nothing | Nothing |
| T/FN state signal output (The NPSW state is output.) |
| The signal cannot be transmitted. Therefore, the signal is not updated. | Nothing | Nothing |
| Signal output during switching (Outputs the state of electric current being applied to the actuator.) |
| The signal cannot be transmitted. Therefore, the signal is not updated. | Nothing | Nothing |
| Electrical load control (Performs idle up according to electrical load, etc.) |
| Idle up according to the electrical load is not performed. | Nothing | Nothing |
| Air conditioning-linked control (Performs idle up according to the compressor load, and performs air conditioning cut control.) |
| Air conditioning-linked control does not operate. | Nothing | Nothing |
| Charging control (Performs idle up according to charging requests.) |
| Idle up according to charging requests is not performed. | Nothing | Nothing |
| Integrated control (VDM)(non driveforce demand) (Calculate driver needed torque by accelerator pedal work) |
| Integrated control is not performed. | Nothing | Nothing |
| ECT indicator in meter (Shift position, switch, mode, etc.) |
| Indicators do not turn on. | Nothing | Nothing |
| AI-SHIFT control (Controls the A/T in order to improve engine braking power and acceleration feeling.) |
| AI-SHIFT control does not operate. | Nothing | Nothing |
| Coast downshift Heater requested upshift delay (Changes the coast down shift point according to the air conditioning load. Performs heater requested upshift delay.) |
| Coast downshift does not operate. | Nothing | Nothing |
| Cruise control (Adjusts the engine throttle valve opening amount automatically to control the vehicle.) |
| Cruise control does not operate. | Nothing | Nothing |
| ABS control (Monitors for tire slippage and performs fluid pressure control to prevent the wheels from locking up in order to maintain vehicle stability and vehicle body deceleration.) |
| The ABS does not operate. | ABS warning light turns on. | U0073 U0100 U0126 |
| MSR control (Prevents the tires from slipping due to engine drag torque by increasing engine torque.) |
| MSR does not operate. | Light turns on. | U0100 |
| TCS control (Prevents excessive tire slippage due to engine torque by decreasing engine torque and increasing pressure to the brakes.) |
| TCS does not operate. | Light turns on. | U0114 |
| VSC control (Reduces excess yaw by increasing brake pressure, and induces necessary yaw by increasing brake pressure and reducing engine torque.) |
| VSC does not operate. | Light turns on. | Nothing |
| Manual mirror adjustment control (Adjusts the outer mirrors according to the auto mirror switch operation.) |
| Manual control is stopped. | Nothing | Nothing |
| Mirror position memorization control (Memorizes the current mirror position.) |
| Memorization control is prohibited. | Nothing | Nothing |
| Mirror position recall control (Recalls the memorized position according to the recall command from the seat ECU.) |
| Recall control is prohibited. | Nothing | Nothing |
| Outer mirror retraction control (Retracts the outer mirrors.) |
| Retraction control is prohibited. | Nothing | Nothing |
| Reverse-linked control (Tilts the mirrors down so that the area around the rear tires is visible when driving the vehicle in reverse.) |
| Reverse-linked operation is stopped. | Nothing | Nothing |
| Active Height Control Suspension (System adjusts damping force based on vehicle conditions and can also adjust the vehicle height.) |
| Damping Force Control (When a vehicle speed of 30 km/h (18 mph) or greater is detected, control continues to operate. Below this speed, the actuators hold the damping force at the fail-safe level, which is the same level as when the vehicle is stopped. (Except for malfunctioning wheel)) Height Control System (Height control maintains the vehicle height at the normal level.) | Light turns on. | U0100 U0122 U0124 U0126 U0140 |
| Steering sensor (Detects the steering wheel angle.) |
| Periodically sends STR1S01 (STS0=1) every 12 ms. | Light turns on | Nothing |
| Auto away/return control (Controls the auto away/return operation according to the SKSW and IG signals. Prohibits auto away/return control.) |
| Auto away/return control does not operate. | Nothing | B2621 B2624 |
| Memorization/recall control (Controls the steering wheel position memorization and recall for the seat position memory.) |
| Memorization/recall control does not operate. | Nothing | B2621 |
| TC DTC output service (While TC = ON is being received from the engine, a DTC is output in response to the request from the combination meter assembly.) |
| The TC service is stopped. | Nothing | Nothing |
| Event data recorder (Records conditions such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the event data recorder recording conditions are met.) |
| An invalid value is stored. | Nothing | Nothing |
| Airbag warning light control (Sends information used for turning the airbag warning light on and off.) |
| - | Nothing | Nothing |
| Collision detection signal (Notifies the system of a collision in order to perform a fuel cut at the time when a vehicle collision occurs.) |
| - | Nothing | Nothing |
| Seat belt warning light control (Sends information used for turning the airbag warning light on and off.) |
| - | Nothing | Nothing |
| Warning control (Displays various warnings in the combination meter according to illumination requests from various ECUs.) |
| The current status is maintained until the ignition switch is turned off, or various warnings illuminate. | Nothing | U0100 |
| Buzzer control (Sounds various buzzers in the combination meter according to sounding requests from various ECUs.) |
| The buzzers do not sound. | Nothing | Nothing |
| Speedometer (Controls the speedometer according to vehicle speed signals.) |
| The speedometer displays 0 km/h (0 mph). | Nothing | U0129 |
| ODO/TRIP meter (Indicates the driven distance in the combination meter according to the vehicle speed pulse signal summation value.) |
| The calculation stops and the last displayed value remains. | Nothing | U0129 |
| Tachometer (Controls the tachometer according to engine speed signals.) |
| The tachometer displays 0 rpm. | Nothing | U0100 |
| Engine coolant temperature gauge (Controls the gauge according to the engine coolant temperature signal.) |
| The temperature gauge needle is at the middle of the "C" mark or below. | Nothing | Nothing |
| Fuel gauge (Receives the starter signal and drives the indicator needle.) |
| Controlled as "ST-OFF". Controlled as "0 km/h (0 mph)". | Nothing | Nothing |
| Oil pressure gauge (Performs a start operation according to the engine speed signal.) |
| Control is performed with the engine speed set to 0 rpm. | Nothing | U0100 |
| Transmission fluid temperature gauge (Controls the gauge according to the transmission fluid signals.) |
| The pointer needle is at the center of the "C" mark or below. | Nothing | Nothing |
| Gear position display (Displays gear position according to the gear position signal and transmission temperature range signal.) |
| The gear position display turns off. SMDE=0 | Nothing | Nothing |
| Combination Meter display (CRUISE INFORMATION display) (Displays vehicle status on the Combination Meter based on status of each CAN signal.) |
| The last signals received are used. | Nothing | Nothing |
| Alarm control (Sounds various warnings.) |
| The warnings do not operate. | Nothing | U1002 U0199 U0208 U1115 U0230 |
| Door lock control (Locks/unlocks the doors.) |
| The vehicle speed auto-lock control does not operate. | Nothing | U1002 U0199 U0208 U1115 U0230 |
| Illumination control (Performs illumination control.) |
| KLEG is maintained. | Nothing | U1002 U0199 U0208 U1115 U0230 |
| Power window control (Performs key off power window control.) |
| KLEG is maintained. | Nothing | U1002 U0199 U0208 U1115 U0230 |
| Light control (Controls the display dimming and daytime running lights.) |
| Daytime running light control is not performed. | Nothing | U1002 U0199 U0208 U1115 U0230 |
| Back door control (Back Door Opener) |
| Power Back Door Buzzer does not sound. Power Back Door Hazard Warning Lights do not operate. One Motion Power Back Door does not operate. Back Door Opener control is prohibited. | Nothing | U1002 U0199 U0208 U1115 U0230 |
| Wireless (Controls the wireless lock/unlock functions.) |
| KLEG is maintained. | Nothing | U1002 U0199 U0208 U1115 U0230 |
| Option Control (Controls optional wireless lock, answer-back optional illumination, alarm warning requests and dome light warning requests.) |
|
| Nothing | U1002 U0199 U0208 U1115 U0230 |
| Lock Control (Sends a door lock request signal.) |
| Lock control is not performed. | Nothing | Nothing |
| Air conditioning control (Requests air conditioning control by sending DFON and ACON signals.) |
| Air conditioning control is not performed. | Nothing | Nothing |
| Hazard answer-back control (Requests hazard blinking through the HZRD bit.) |
| Hazard answer-back control is not performed. | Nothing | Nothing |