Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > FAIL-SAFE CHART

for Preparation Click here



FAIL-SAFE FUNCTION
  1. When communication fails in any of the main wires (communication lines) due to a short circuit or other causes, the fail-safe function, which is specified for each system, operates to prevent the system from malfunctioning.

  2. The table below shows the effects on each system when communication is impossible. For further details, refer to each system.

    Function
    Behavior during CAN Failure
    1. Control Master
    2. System Related
    Vehicle Behavior
    Indicator and Buzzer
    Diagnostic Trouble Code
    Blind Spot Detection
    (Warns the driver when the system detects a vehicle in the blind spot of an outer mirror.)
    1. Main body ECU (cowl side junction block LH), Blind spot monitor sensor LH, Blind spot monitor sensor RH
    2. ECM, Brake actuator assembly (skid control ECU), Steering angle sensor
    Maintains previous values.
    "CHECK BSM SYSTEM" is displayed on the multi-information display.
    1. U0100
    2. U0126
    3. U0129
    4. U0142
    5. U0232
    6. U0233
    Relay Function
    (Transmits relay frames and does not transmit nonrelay frames.)
    1. Network gateway ECU
    2. Main body ECU (cowl side junction block LH), ECM, Brake actuator assembly (skid control ECU), steering angle sensor, Combination meter assembly, Center airbag sensor assembly, Air conditioning amplifier assembly, Bus buffer ECU, Blind spot monitor sensor LH, Blind spot monitor sensor RH, DLC3, 4 wheel drive control ECU (4WD control ECU), Suspension control ECU, Power steering ECU assembly
    CAN controller is reset.
    Nothing
    Nothing
    Diagnostic Function
    (Determines the connection and communication status of ECUs which are connected to the V2 bus)
    1. Network gateway ECU
    2. Blind spot monitor sensor LH, Blind spot monitor sensor RH
    CAN controller is reset.
    Nothing
    1. U0104
    2. U0232
    3. U0233
    4. U1002
    NM Function
    (Performs communication via NM frames with ECUs that are equipped with NM, and controls the CAN communication sleep/ wake up functions.)
    1. Network gateway ECU
    2. Main body ECU (cowl side junction block LH), Combination meter assembly, Bus buffer ECU
    CAN controller is reset.
    Nothing
    Nothing
    CCP Function
    (Communicates with devices connected via the V-bus and monitors the RAM in the gateway ECU.)
    1. Network gateway ECU
    2. DLC3
    CAN controller is reset.
    Nothing
    Nothing
    VFC control
    (Changes the power steering fluid flow according to the state of the vehicle using the vehicle speed, engine speed, steering angle and towing information.)
    1. Power steering ECU assembly
    2. ECM, Brake actuator assembly (skid control ECU), Steering angle sensor
    Alternative control (The steering angle, vehicle speed and engine speed are fixed.)
    PPS indicator light turns on
    U0073
    Air conditioning control
    (Performs engine-linked control based on sensor information and controls the air conditioning and panel.)
    1. Air conditioning amplifier assembly
    2. Main body ECU (cowl side junction block LH), ECM, Combination meter assembly, Bus buffer ECU
    Maintains previous values.
    Nothing
    Nothing
    Power back door operation condition
    (Prohibit PBD function according to vehicle condition (IG, shift position P, vehicle speed, remote start, lock position)
    1. Power back door unit assembly (power back door ECU)
    2. ECM, Combination meter assembly, Main body ECU (cowl side junction block LH), Bus buffer ECU
    PBD does not work. (Warn with buzzer when operation request is received.)
    Buzzer
    Nothing
    Power back door operation request
    (Start PBD operation by receiving request trigger from operation switch, wireless switch)
    1. Power back door unit assembly (power back door ECU)
    2. Main body ECU (cowl side junction block LH)
    PBD does not work.
    Nothing
    Nothing
    Power back door operation status output
    (Output hazard ON request and door status during PBD working)
    1. Power back door unit assembly (power back door ECU)
    2. Main body ECU (cowl side junction block LH)
    Indicator in meter is not ON when PBD is open. Hazard is not ON when PBD is operated.
    Nothing
    Nothing
    Driver side seat memory system
    (Memorizes and recalls the driver side seat, steering wheel and outside mirror positions.)
    1. Front power seat switch LH (power seat control ECU)
    2. Outer mirror control ECU assembly, Multiplex tilt and telescopic ECU, Main body ECU (cowl side junction block LH), ECM, Combination meter assembly
    Position memorization and recall cannot be performed. The tilt and telescopic system does not operate.
    Nothing
    Nothing
    2WD-4WD switching limitation
    (Switching between 2WD and 4WD is prohibited when the vehicle speed is outside the acceptable range.)
    1. 4 wheel drive control ECU (4WD control ECU)
    2. Brake actuator assembly (skid control ECU)
    Switching between 2WD and 4WD is prohibited.
    Indicator light blinks
    Nothing
    High-Low switching limitation
    (Prohibits High-Low switching when the vehicle speed or engine speed is outside the acceptable range or the A/T is not in N during the A/T status check.)
    1. 4 wheel drive control ECU (4WD control ECU)
    2. ECM, Brake actuator assembly (skid control ECU)
    High-Low switching is prohibited.
    Indicator light blinks
    Nothing
    Center differential lock switching control
    (Center differential lock switching is prohibited when there is a vehicle speed violation or large difference in wheel speeds.)
    1. 4 wheel drive control ECU (4WD control ECU)
    2. Brake actuator assembly (skid control ECU)
    Center differential lock switching is prohibited.
    Indicator light blinks
    Nothing
    L4F switching control
    (Switching to L4F is prohibited and the operation is performed with L4L when VSC is malfunctioning.)
    1. 4 wheel drive control ECU (4WD control ECU)
    2. Brake actuator assembly (skid control ECU)
    L4F switching is prohibited
    Indicator light blinks
    Nothing
    Control performed during low temperatures
    (Changes the value of the electric current applied to the ACT according to the temperature.)
    1. 4 wheel drive control ECU (4WD control ECU)
    2. ECM, Air conditioning amplifier assembly
    Changes to the temperature used for ACT temperature correction control calculations.
    Nothing
    Nothing
    Specialized control during wheel speed failure
    (When there is a wheel speed failure, switching is permitted only when specified conditions are met (the wheel speed malfunction is 1 wheel or more and 3 wheels or less, the brake is applied, the engine speed is low, and all normal wheel speeds are low.))
    1. 4 wheel drive control ECU (4WD control ECU)
    2. ECM, Brake actuator assembly (skid control ECU)
    If the wheel speed malfunction is 1 wheel or more and 3 wheels or less, only when the wheel speed failure specified conditions are met, switching is permitted. When 4 wheels are malfunctioning, switching is prohibited (the wheel speed failure specialized control does not operate).
    Indicator light blinks
    Nothing
    Vehicle speed threshold limitation
    (Determines whether the temperature is low or normal and changes the vehicle speed at which shifting from to 2 to 4 is prohibited.)
    1. 4 wheel drive control ECU (4WD control ECU)
    2. Air conditioning amplifier assembly
    Uses the threshold value for low temperatures.
    Nothing
    Nothing
    Indicator and buzzer signal output
    (Outputs a signal indicating the state of the indicators and buzzers, which represent the actuator position and switching status.)
    1. 4 wheel drive control ECU (4WD control ECU)
    2. -
    The signal cannot be transmitted. Therefore, the signal is not updated.
    Nothing
    Nothing
    Cruise control cancel signal output
    (Outputs a cruise control cancel signal when center differential switching is not completed even though 5 seconds or more have elapsed from the start of switching.)
    1. 4 wheel drive control ECU (4WD control ECU)
    2. -
    The signal cannot be transmitted. Therefore, the signal is not updated.
    Nothing
    Nothing
    L4 state signal output
    (Outputs a signal when switching to the L4 position is finished.)
    1. 4 wheel drive control ECU (4WD control ECU)
    2. -
    The signal cannot be transmitted. Therefore, the signal is not updated.
    Nothing
    Nothing
    4WD state signal output
    (The ADDSW state is output.)
    1. 4 wheel drive control ECU (4WD control ECU)
    2. -
    The signal cannot be transmitted. Therefore, the signal is not updated.
    Nothing
    Nothing
    T/FN state signal output
    (The NPSW state is output.)
    1. 4 wheel drive control ECU (4WD control ECU)
    2. -
    The signal cannot be transmitted. Therefore, the signal is not updated.
    Nothing
    Nothing
    Motor Operation Signal Output
    (Outputs the state of the actuator.)
    1. 4 wheel drive control ECU (4WD control ECU)
    2. -
    The signal cannot be transmitted. Therefore, the signal is not updated.
    Nothing
    Nothing
    Electrical load control
    (Performs idle up according to electrical load, etc.)
    1. ECM
    2. Main body ECU (cowl side junction block LH), Air conditioning amplifier assembly
    Idle up according to the electrical load is not performed.
    Nothing
    Nothing
    Air conditioning-linked control
    (Performs idle up according to the compressor load, and performs air conditioning cut control.)
    1. ECM
    2. Air conditioning amplifier assembly
    Air conditioning-linked control does not operate.
    Nothing
    Nothing
    Charging control
    (Performs idle up according to charging requests.)
    1. ECM
    2. Main body ECU (cowl side junction block LH), Air conditioning amplifier assembly
    Idle up according to charging requests is not performed.
    Nothing
    Nothing
    Integrated control (VDM) (drive force)
    (Calculates the driver requested torque based on accelerator pedal operation.)
    1. ECM
    2. Brake actuator assembly (skid control ECU), Steering angle sensor
    Integrated control is not performed.
    Nothing
    Nothing
    ECT indicator in meter
    (Shift position, switch, mode, etc.)
    1. ECM
    2. Main body ECU (cowl side junction block LH), Combination meter assembly
    Indicators do not turn on.
    Nothing
    Nothing
    AI-SHIFT control
    (Controls the A/T in order to improve engine braking power and acceleration feeling.)
    1. ECM
    2. Brake actuator assembly (skid control ECU)
    AI-SHIFT control does not operate.
    Nothing
    Nothing
    Coast downshift
    (Changes the coast down shift point according to the air conditioning load.)
    Heater requested upshift delay
    (Performs heater requested upshift delay.)
    1. ECM
    2. Air conditioning amplifier assembly
    Coast downshift does not operate.
    Nothing
    Nothing
    Cruise control
    (Adjusts the engine throttle valve opening amount automatically to control the vehicle.)
    1. ECM
    2. Brake actuator assembly (skid control ECU), Combination meter assembly
    Cruise control does not operate.
    Nothing
    Nothing
    ABS control
    (Monitors for tire slippage and performs fluid pressure control to prevent the wheels from locking up in order to maintain vehicle stability and vehicle body deceleration.)
    1. Brake actuator assembly (skid control ECU)
    2. 4 wheel drive control ECU (4WD control ECU)
    The ABS does not operate.
    ABS warning light turns on.
    1. U0073
    2. U0100
    3. U0126
    MSR control
    (Prevents the tires from slipping due to engine drag torque by increasing engine torque.)
    1. Brake actuator assembly (skid control ECU)
    2. ECM, Steering angle sensor, 4 wheel drive control ECU (4WD control ECU)
    MSR does not operate.
    Light turns on.
    U0100
    TCS control
    (Prevents excessive tire slippage due to engine torque by decreasing engine torque and increasing pressure to the brakes.)
    1. Brake actuator assembly (skid control ECU)
    2. ECM, Steering angle sensor, 4 wheel drive control ECU (4WD control ECU)
    TCS does not operate.
    Light turns on.
    U0114
    VSC control
    (Reduces excess yaw by increasing brake pressure, and induces necessary yaw by increasing brake pressure and reducing engine torque.)
    1. Brake actuator assembly (skid control ECU)
    2. ECM, Steering angle sensor, 4 wheel drive control ECU (4WD control ECU)
    VSC does not operate.
    Light turns on.
    Nothing
    Manual mirror adjustment control
    (Adjusts the outer mirrors according to the auto mirror switch operation.)
    1. Outer mirror control ECU assembly
    2. Main body ECU (cowl side junction block LH)
    Manual control is stopped.
    Nothing
    Nothing
    Mirror position memorization control
    (Memorizes the current mirror position.)
    1. Outer mirror control ECU assembly
    2. Front power seat switch LH (power seat control ECU), Main body ECU (cowl side junction block LH)
    Memorization control is prohibited.
    Nothing
    Nothing
    Mirror position recall control
    (Recalls the memorized position according to the recall command from the seat ECU.)
    1. Outer mirror control ECU assembly
    2. Front power seat switch LH (power seat control ECU)
    Recall control is prohibited.
    Nothing
    Nothing
    Outer mirror retraction control
    (Retracts the outer mirrors.)
    1. Outer mirror control ECU assembly
    2. Main body ECU (cowl side junction block LH)
    Retraction control is prohibited.
    Nothing
    Nothing
    Reverse-linked control
    (Tilts the mirrors down so that the area around the rear tires is visible when driving the vehicle in reverse.)
    1. Outer mirror control ECU assembly
    2. Main body ECU (cowl side junction block LH)
    Reverse-linked operation is stopped.
    Nothing
    Nothing
    Active Height Control Suspension
    (System adjusts damping force based on vehicle conditions and can also adjust the vehicle height.)
    1. Suspension control ECU
    2. Main body ECU (cowl side junction block LH), ECM, Brake actuator assembly (skid control ECU), Steering angle sensor
    Damping Force Control
    (When a vehicle speed of 30 km/h (18 mph) or more is detected, control continues to operate. Below this speed, the actuators hold the damping force at the fail-safe level, which is the same level as when the vehicle is stopped. (Except for malfunctioning wheel))
    Height Control System
    (Height control maintains the vehicle height at the normal level.)
    Light turns on.
    1. U0100
    2. U0122
    3. U0124
    4. U0126
    5. U0140
    Steering sensor
    (Detects the steering wheel angle.)
    1. Steering angle sensor
    2. Brake actuator assembly (skid control ECU)
    Periodically sends STR1S01 (STS0=1) every 12 ms.
    Light turns on
    Nothing
    Auto away/return control
    (Controls the auto away/return operation according to the SKSW and IG signals. Prohibits auto away/return control.)
    1. Multiplex tilt and telescopic ECU
    2. Main body ECU (cowl side junction block LH), Combination meter assembly, Bus buffer ECU
    Auto away/return control does not operate.
    Nothing
    1. B2621
    2. B2624
    Memorization/recall control
    (Controls the steering wheel position memorization and recall for the seat position memory.)
    1. Multiplex tilt and telescopic ECU
    2. Front power seat switch LH (power seat control ECU)
    Memorization/recall control does not operate.
    Nothing
    B2621
    TC DTC output service
    (While TC = ON is being received from the engine, a DTC is output in response to the request from the combination meter assembly.)
    1. Combination meter assembly
    2. ECM, Center airbag sensor assembly
    The TC service is stopped.
    Nothing
    Nothing
    Event data recorder
    (Records conditions such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the event data recorder recording conditions are met.)
    1. Center airbag sensor assembly
    2. ECM, Steering angle sensor, Brake actuator assembly (skid control ECU)
    An invalid value is stored.
    Nothing
    Nothing
    Airbag warning light control
    (Sends information used for turning the airbag warning light on and off.)
    1. Combination meter assembly
    2. Center airbag sensor assembly
    -
    Nothing
    Nothing
    Collision detection signal
    (Notifies the system of a collision in order to perform a fuel cut at the time when a vehicle collision occurs.)
    1. ECM
    2. Center airbag sensor assembly
    -
    Nothing
    Nothing
    Seat belt warning light control
    (Sends information used for turning the airbag warning light on and off.)
    1. Main body ECU (cowl side junction block LH), Combination meter assembly
    2. Center airbag sensor assembly
    -
    Nothing
    Nothing
    Warning control
    (Displays various warnings in the combination meter according to illumination requests from various ECUs.)
    1. Combination meter assembly
    2. Main body ECU (cowl side junction block LH), ECM, Brake actuator assembly (skid control ECU), Center airbag sensor assembly, 4 wheel drive control ECU (4WD control ECU), Suspension control ECU, Power steering ECU assembly
    The current status is maintained until the ignition switch is turned off, or various warnings illuminate.
    Nothing
    U0100
    Buzzer control
    (Sounds various buzzers in the combination meter according to sounding requests from various ECUs.)
    1. Combination meter assembly
    2. Main body ECU (cowl side junction block LH), ECM, Brake actuator assembly (skid control ECU), 4 wheel drive control ECU (4WD control ECU)
    The buzzers do not sound.
    Nothing
    Nothing
    Meter Information Output 1
    (Sends vehicle speed signals, tail cancel signals and signals indicating the temperature units.)
    1. Combination meter assembly
    2. -
    -
    Nothing
    Nothing
    Meter Information Output 2
    (Sends destination information signals, steering wheel signals, signals indicating odometer units and odometer information signals.)
    1. Combination meter assembly
    2. -
    -
    Nothing
    Nothing
    Meter Information Output 13
    (Sends a signal indicating the amount of fuel remaining in the main fuel tank and a signal indicating the amount of fuel remaining in the sub fuel tank.)
    1. Combination meter assembly
    2. -
    -
    Nothing
    Nothing
    Meter Information Output 15
    (Sends fuel sender gauge signals.)
    1. Combination meter assembly
    2. -
    -
    Nothing
    Nothing
    Telltale
    (Controls indicator illumination and blinking according to CAN signals.)
    1. Combination meter assembly
    2. Main body ECU (cowl side junction block LH), Brake actuator assembly (skid control ECU), Center airbag sensor assembly, Suspension control ECU, Power steering ECU assembly
    Control is performed using information from the last signal received or indicators are illuminated.
    Nothing
    U0129
    Speedometer
    (Controls the speedometer according to vehicle speed signals.)
    1. Combination meter assembly
    2. Brake actuator assembly (skid control ECU)
    The speedometer displays 0 km/h (0 mph).
    Nothing
    U0129
    ODO/TRIP meter
    (Indicates the driven distance in the combination meter according to the vehicle speed pulse signal summation value.)
    1. Combination meter assembly
    2. Brake actuator assembly (skid control ECU)
    The calculation stops and the last displayed value remains.
    Nothing
    U0129
    Tachometer
    (Controls the tachometer according to engine speed signals.)
    1. Combination meter assembly
    2. ECM
    The tachometer displays 0 rpm.
    Nothing
    U0100
    Engine coolant temperature gauge
    (Controls the gauge according to the engine coolant temperature signal.)
    1. Combination meter assembly
    2. ECM
    The temperature gauge needle is at the middle of the "C" mark or below.
    Nothing
    Nothing
    Fuel gauge
    (Receives the starter signal and drives the indicator needle.)
    1. Combination meter assembly
    2. ECM
    Controlled as "ST-OFF".
    Controlled as "0 km/h (0 mph)".
    Nothing
    Nothing
    Oil pressure gauge
    (Performs a start operation according to the engine speed signal.)
    1. Combination meter assembly
    2. ECM
    Control is performed with the engine speed set to 0 rpm.
    Nothing
    U0100
    Transmission fluid temperature gauge
    (Controls the gauge according to the transmission fluid signals.)
    1. Combination meter assembly
    2. ECM
    The pointer needle is at the center of the "C" mark or below.
    Nothing
    Nothing
    Gear position display
    (Displays gear position according to the gear position signal and transmission temperature range signal.)
    1. Combination meter assembly
    2. ECM
    The gear position display turns off.
    SMDE=0
    Nothing
    Nothing
    Combination Meter display (CRUISE INFORMATION display)
    (Displays vehicle status on the Combination Meter based on status of each CAN signal.)
    1. Combination meter assembly
    2. ECM
    The last signals received are used.
    Nothing
    Nothing
    Alarm control
    (Sounds various warnings.)
    1. Main body ECU (cowl side junction block LH)
    2. Power back door unit assembly (power back door ECU), ECM, Bus buffer ECU
    The warnings do not operate.
    Nothing
    1. U0199
    2. U0208
    3. U0230
    4. U1002
    5. U1115
    Door lock control
    (Locks/unlocks the doors.)
    1. Main body ECU (cowl side junction block LH)
    2. ECM, Combination meter assembly, Center airbag sensor assembly, Bus buffer ECU
    The vehicle speed auto-lock control does not operate.
    Nothing
    1. U0199
    2. U0208
    3. U0230
    4. U1002
    5. U1115
    Illumination control
    (Performs illumination control.)
    1. Main body ECU (cowl side junction block LH)
    2. Bus buffer ECU
    KLEG is maintained.
    Nothing
    1. U0199
    2. U0208
    3. U0230
    4. U1002
    5. U1115
    Power window control
    (Performs key off power window control.)
    1. Main body ECU (cowl side junction block LH)
    2. Bus buffer ECU
    KLEG is maintained.
    Nothing
    1. U0199
    2. U0208
    3. U0230
    4. U1002
    5. U1115
    Light control
    (Controls the display dimming and daytime running lights.)
    1. Main body ECU (cowl side junction block LH)
    2. ECM, Center airbag sensor assembly
    Daytime running light control is not performed.
    Nothing
    1. U0199
    2. U0208
    3. U0230
    4. U1002
    5. U1115
    Back door control
    (Back Door Opener)
    1. Main body ECU (cowl side junction block LH)
    2. Power back door unit assembly (power back door ECU), Combination meter assembly
    Power Back Door Buzzer does not sound.
    Power Back Door Hazard Warning Lights do not operate.
    One Motion Power Back Door does not operate.
    Back Door Opener control is prohibited.
    Nothing
    1. U0199
    2. U0208
    3. U0230
    4. U1002
    5. U1115
    Wireless
    (Controls the wireless lock/unlock functions.)
    1. Main body ECU (cowl side junction block LH)
    2. Bus buffer ECU
    KLEG is maintained.
    Nothing
    1. U0199
    2. U0208
    3. U0230
    4. U1002
    5. U1115
    Option Control
    (Controls optional wireless lock, answer-back optional illumination, alarm warning requests and dome light warning requests.)
    1. Main body ECU (cowl side junction block LH)
    2. Bus buffer ECU
    1. Optional wireless lock control does not operate.
    2. Answer-back control for optional illumination does not operate.
    3. Alarm warning request control does not operate.
    4. Dome light warning request control does not operate.
    Nothing
    1. U0199
    2. U0208
    3. U0230
    4. U1002
    5. U1115
    Lock Control
    (Sends a door lock request signal.)
    1. Bus buffer ECU
    2. Main body ECU (cowl side junction block LH)
    Lock control is not performed.
    Nothing
    Nothing
    Air conditioning control
    (Requests air conditioning control by sending DFON and ACON signals.)
    1. Bus buffer ECU
    2. -
    Air conditioning control is not performed.
    Nothing
    Nothing
    Hazard answer-back control
    (Requests hazard blinking through the HZRD bit.)
    1. Bus buffer ECU
    2. Main body ECU (cowl side junction block LH)
    Hazard answer-back control is not performed.
    Nothing
    Nothing