Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

E127561E05

  1. Disconnect the H24 and H67 air conditioning amplifier connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H24-1 (IG+) - Body ground
    P - Body ground
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    H24-14 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    H24-21 (B) - Body ground
    R - Body ground
    Battery power source
    Always
    11 to 14 V
    H67-20 (RGND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    H67-24 (+B2) - Body ground
    LG - Body ground
    Battery power source
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the H24 and H67 air conditioning amplifier connectors.

  4. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Check from the rear of the connector with it connected to the air conditioning amplifier.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H24-5 (TAM) - H24-13 (SG-2)
    V - G
    A/C ambient temperature sensor signal
    Ignition switch ON
    at 25°C (77°F)
    1.35 to 1.75 V
    Ignition switch ON
    at 40°C (104°F)
    0.9 to 1.2 V
    H24-8 (LOCK) - H24-13 (SG-2)
    SB - G
    A/C compressor lock sensor signal
    Engine is running
    Blower switch LO
    A/C switch on
    Pulse generation
    (see waveform 1)
    H24-9 (PRE) - Body ground
    Y - Body ground
    A/C pressure sensor signal
    Refrigerant pressure: normal
    0.5 to 4.8 V
    H24-10 (S5-3) - Body ground
    R - Body ground
    Power supply for pressure sensor
    Ignition switch ON
    4.5 to 5.5 V
    H24-11 (CANH) - H24-14 (GND)
    B - W-B
    Hi-level CAN bus line
    Ignition switch ON
    Pulse generation
    (see waveform 2)
    H24-12 (CANL) - H24-14 (GND)
    W - W-B
    Lo-level CAN bus line
    Ignition switch ON
    Pulse generation
    (see waveform 3)
    H24-13 (SG-2) - Body ground
    G - Body ground
    Ground for ambient temperature sensor
    Always
    Below 1 Ω
    H24-17 (AC1) - H24-14 (GND)
    B - W-B
    Idle-up request signal
    Engine idling
    Magnet clutch is not engaged
    11 to 14 V
    Engine idling
    Magnet clutch is engaged
    Below 1 V
    H24-18 (MHTR) - H24-14 (GND)
    L - W-B
    Mirror heater relay drive signal
    Mirror heater switch off→on
    11 to 14 V → Below 1 V
    H24-20 (MGC) - H24-14 (GND)
    P - W-B
    A/C compressor magnet clutch operation signal
    Ignition switch ON
    Blower switch LO
    A/C switch off
    11 to 14 V
    Ignition switch ON
    Blower switch LO
    A/C switch on
    Below 1 V
    H24-23 (BLW) - H24-14 (GND)
    LG - W-B
    Blower motor control signal
    Ignition switch ON
    Blower switch LO
    Pulse generation
    (see waveform 4)
    H24-27 (ACT) - H24-14 (GND)
    L - W-B
    A/C compressor magnet clutch on permit signal
    Engine idling → Accelerator pedal depressed (Air conditioning cut signal output when engine load increases rapidly)
    11 to 14 V → Below 2 V
    H24-29 (TR) - H24-34 (SG-1)
    G - B
    Room temperature sensor signal
    Ignition switch ON
    Front side interior temperature: 25°C (77°F)
    1.8 to 2.2 V
    H24-32 (TSP) - Body ground
    L - Body ground
    Passenger side solar sensor signal
    Ignition switch ON
    Solar sensor subjected to electric light
    0.8 to 4.3 V
    H24-33 (TSD) - Body ground
    P - Body ground
    Driver side solar sensor signal
    Ignition switch ON
    Solar sensor subjected to electric light
    0.8 to 4.3 V
    H24-34 (SG-1) - Body ground
    B - Body ground
    Ground for room temperature sensor
    Always
    Below 1 Ω
    H24-37 (LIN1) - H24-14 (GND)
    SB - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation
    H24-38 (RDEF) - H24-14 (GND)
    R - W-B
    Defogger relay drive signal
    Defogger switch off→on
    11 to 14 V → Below 1 V
    H24-39 (CFN+) - H24-14 (GND)
    V - W-B
    Condenser fan relay signal rive signal
    Ignition switch ON
    Condenser fan off→on
    11 to 14 V → Below 1 V
    H24-16 (CFN-) - H24-14 (GND)
    Y - W-B
    Condenser fan relay signal rive signal
    Ignition switch ON
    Condenser fan off→on
    11 to 14 V → Below 1 V
    H67-1 (RBUS) - H67-21 (RBUG)
    V - G
    BUS IC control signal
    Ignition switch off → ON
    Pulse generation
    H67-4 (TEC) - H67-19 (SGND)
    R - L
    Rear evaporator temperature sensor signal
    Ignition switch ON
    Evaporator temperature at 0°C (32°F)
    1.7 to 2.1 V
    H67-6 (SG-5) - Body ground
    BR - Body ground
    Ground for seat blower switch
    Always
    Below 1 Ω
    H67-7 (SG-6) - Body ground
    P - Body ground
    Ground for rear room temperature sensor
    Always
    Below 1 Ω
    H67-8 (S5-2) - H67-6 (SG-5)
    SB - BR
    Power supply for seat blower switch
    Ignition switch ON
    4.5 to 5.5 V
    H67-9 (SHD+) - H67-20 (RGND)
    W - W-B
    Driver seat blower drive signal
    Ignition switch ON
    Pulse generation
    H67-10 (SHP+) - H67-20 (RGND)
    BE - W-B
    Passenger seat blower drive signal
    Ignition switch ON
    Pulse generation
    H67-13 (RLIN) - H67-20 (RGND)
    B - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation
    H67-15 (AD-4) - H67-20 (RGND)
    GR - W-B
    Driver seat blower switch signal
    Ignition switch ON
    Driver seat blower switch 0 position
    4.5 to 5.5 V
    Ignition switch ON
    Driver seat blower switch 3 position
    Below 1 V
    H67-16 (AD-5) - H67-20 (RGND)
    W - W-B
    Passenger seat blower switch signal
    Ignition switch ON
    Passenger seat blower switch 0 position
    4.5 to 5.5 V
    Ignition switch ON
    Passenger seat blower switch 3 position
    Below 1 V
    H67-17 (TR) - H67-7 (SG-6)
    L - P
    Rear room temperature sensor signal
    Ignition switch ON
    Rear side interior temperature: 25°C (77°F)
    1.8 to 2.2 V
    H67-19 (SGND) - Body ground
    L - Body ground
    Ground for rear evaporator temperature sensor
    Always
    Below 1 Ω
    H67-21 (RBUG) - Body ground
    G - Body ground
    Ground for BUS IC
    Always
    Below 1 Ω
    H67-22 (BLWH) - H67-20 (RGND)
    P - W-B
    Rear blower motor control signal
    Ignition switch ON
    Blower switch LO
    Pulse generation
    (see waveform 5)
    H67-23 (RBBU) - H67-21 (RBUG)
    Y - G
    Power supply for BUS IC
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    H24-19 (RMGV) - H24-14 (GND)
    BE - W-B
    Rear magnetic valve signal
    Ignition switch ON
    Rear switch on
    Below 1 V
    H24-19 (RMGV) - H24-14 (GND)
    BE - W-B
    Rear magnetic valve signal
    Ignition switch ON
    Rear switch off
    11 to 14 V
    z13-2 (BUS G) - Body ground
    -
    Ground for BUS IC
    Always
    Below 1 Ω
    z13-3 (BUS) - z13-2 (BUS G)
    -
    BUS IC control signal
    Ignition switch off → ON
    Pulse generation
    z13-4 (B BUS) - z13-2 (BUS G)
    -
    Power supply for BUS IC
    Ignition switch off
    Below 1 V
    z13-4 (B BUS) - z13-2 (BUS G)
    -
    Ignition switch ON
    11 to 14 V
    z13-5 (SGA) - Body ground
    -
    Ground for evaporator temperature sensor
    Always
    Below 1 Ω
    z13-6 (TEA) - z13-5 (SGA)
    -
    A/C evaporator temperature sensor signal
    Ignition switch ON
    Evaporator temperature at 0°C (32°F)
    1.7 to 2.1 V
    z13-6 (TEA) - z13-5 (SGA)
    -
    Ignition switch ON
    Evaporator temperature at 15°C (59°F)
    0.7 to 1.3 V
    1. If the result is not as specified, the amplifier may have a malfunction.



  5. E147483E02
  6. Waveform 1: Using an oscilloscope
    Compressor Lock Signal 
    Item
    Content
    Terminal No. (Symbol)
    H24-8 (LOCK) - H24-13 (SG-2)
    Tool Setting
    200 mV/DIV., 10 ms./DIV.
    Condition
    Engine is running
    Blower switch LO
    A/C switch ON



  7. A086154E45
  8. Waveform 2 (Reference) : Using an oscilloscope
    CAN Communication Signal 
    Item
    Content
    Terminal No. (Symbol)
    H24-11 (CANH) - H24-14 (GND)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.



  9. A086155E42
  10. Waveform 3 (Reference) : Using an oscilloscope
    CAN Communication Signal 
    Item
    Content
    Terminal No. (Symbol)
    H24-12 (CANL) - H24-14 (GND)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.



  11. E103396E18
  12. Waveform 4 : Using an oscilloscope
    Blower Motor Control Signal 
    Item
    Content
    Terminal No. (Symbol)
    H24-23 (BLW) - H24-14 (GND)
    Tool Setting
    1 V/DIV., 500 μsec./DIV.
    Condition
    Ignition switch ON
    Blower switch LO

    HINT:
    When the blower level is increased, the duty ratio changes accordingly.



  13. E103396E19
  14. Waveform 5 : Using an oscilloscope
    Rear Blower Motor Control Signal 
    Item
    Content
    Terminal No. (Symbol)
    H67-22 (BLWH) - H67-20 (RGND)
    Tool Setting
    1 V/DIV., 500 μsec./DIV.
    Condition
    Ignition switch ON
    Blower switch LO

    HINT:
    When the blower level is increased, the duty ratio changes accordingly.


CHECK INTEGRATION CONTROL AND PANEL

B160782E03

  1. Disconnect the H45 integration control and panel connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H45-16 (IG+) - H45-1 (GND)
    P - W-B
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    H45-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    H45-9 (OFF) - H45-10 (AUTO)
    GR - LG
    Steering pad switch signal
    Always
    10 kΩ or higher
    Steering pad switch push to AUTO
    Below 2.5 Ω
    Steering pad switch push to OFF
    313 to 345 Ω
    Steering pad switch push to TEMP+
    950 to 1050 Ω
    Steering pad switch push to TEMP-
    2955 to 3266 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the H45 integration control and panel connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H45-3 (STX) - H45-1 (GND)
    SB - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation

    1. If the result is not as specified, the integration control and panel may have a malfunction.


CHECK AIR CONDITIONING CONTROL ASSEMBLY

E161557E01

  1. Disconnect the S4 air conditioning control assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S4-1 (IG) - S4-4 (E)
    P - W-B
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    S4-4 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the S4 air conditioning control assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S4-5 (RLIN) - S4-4 (E)
    GR - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation

    1. If the result is not as specified, the air conditioning control may have a malfunction.