DTC B1421/21 Solar Sensor Circuit (Passenger Side) |

| DTC Code | DTC Detection Condition | Trouble Area |
| B1421/21 | An open or short in the passenger side solar sensor circuit. |
|

| 1.READ VALUE USING INTELLIGENT TESTER (PASSENGER SIDE SOLAR SENSOR) |
Use the Data List to check if the automatic light control sensor is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Solar Sensor (P Side) | Passenger side solar sensor / Min.: 0 Max.: 255 | Passenger side solar sensor voltage increases as brightness increases | Open in the circuit: 0 Short in the circuit: 255 |
| Result | Proceed to |
| NG | A |
| OK (When troubleshooting according to Problem Symptoms Table) | B |
| OK (When troubleshooting according to the DTC output) | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (SENSOR SYSTEM VOLTAGE) |
![]() |
Disconnect the I21 sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I21-3 (CLTE) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| I21-6 (CLTB) - I21-3 (CLTE) | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - AIR CONDITIONING AMPLIFIER) |
![]() |
Disconnect the H24 amplifier connector.
Disconnect the I21 sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H24-32 (TSP) - I21-2 (TSR) | Always | Below 1 Ω |
| H24-32 (TSP) or I21-2 (TSR) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK AUTOMATIC LIGHT CONTROL SENSOR (TSR - CLTE VOLTAGE) |
![]() |
Remove the automatic light control sensor (solar sensor) with its connector still connected (Click here).
Apply battery voltage between terminals 6 (CLTB) and 3 (CLTE) of the solar sensor.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (TSR) - 3 (CLTE) | Sensor is subjected to electric light | 0.8 to 4.3 V |
| Sensor is covered with a cloth | Below 0.8 V |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR) |
![]() |
Disconnect the H3 ECU connector.
Disconnect the I21 sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H3-18 (CLTE) - I21-3 (CLTE) | Always | Below 1 Ω |
| H3-20 (CLTB) - I21-6 (CLTB) | Always | Below 1 Ω |
| H3-18 (CLTE) or I21-3 (CLTE) - Body ground | Always | 10 kΩ or higher |
| H3-20 (CLTB) or I21-6 (CLTB) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||