Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > Air Conditioning Compressor Magnetic Clutch Circuit

for Preparation Click here


DESCRIPTION

When the air conditioning amplifier assembly is turned on, a magnet clutch on signal is sent from the MGC terminal of the air conditioning amplifier assembly. Then, the magnet clutch relay turns on to operate the magnet clutch.

WIRING DIAGRAM


E146216E04


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Use the intelligent tester to check if the CAN communication system is functioning normally.

    OK:
    CAN DTC is not output.



NG
GO TO CAN COMMUNICATION SYSTEM (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (AIR CONDITIONING SWITCH SIGNAL)
  1. Use the Data List to check if the air conditioning switch is functioning properly.

    ECM 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/C Signal
    Air conditioning switch signal /
    ON or OFF
    ON: Air conditioning on
    OFF: Air conditioning off
    -

    OK:
    The display is as specified in the normal condition.



NG
Go to step 3
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

3.INSPECT FUSE (A/C IG)


    E160643E13
  1. Remove the A/C IG fuse from the main body ECU (cowl side junction block LH).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A/C IG fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


4.INSPECT MAGNET CLUTCH RELAY
B060778E04
  1. Remove the magnet clutch relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied between terminals
    10 kΩ or higher
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE MAGNET CLUTCH RELAY
OK


5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)
E124470E57
  1. Disconnect the H24 amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H24-20 (MGC) - Body ground
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (MGC VOLTAGE)
E124471E86
  1. Reconnect the H24 amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H24-20 (MGC) - Body ground
    Engine running and air conditioning switch on
    Below 1 V
    Engine running and air conditioning switch off
    11 to 14 V



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK


7.INSPECT COOLER COMPRESSOR ASSEMBLY (COMPRESSOR HARNESS)
E146414E03
  1. Disconnect the D39 compressor connector.

  1. Disconnect the magnet clutch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (MG+) - 1
    Always
    Below 1 Ω
    3 (MG+) - Body ground
    Always
    10 kΩ or higher



NG
REPLACE COOLER COMPRESSOR ASSEMBLY (Click here)
OK


8.INSPECT MAGNET CLUTCH ASSEMBLY
  1. Disconnect the magnet clutch connector.



    E146516E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    Always
    3.4 to 3.8 Ω

  1. When connector terminal 1 is connected to the positive (+) battery terminal, check that the following occurs: 1) the magnet clutch operating sound can be heard, and 2) the magnet clutch hub and rotor lock.



NG
REPLACE MAGNET CLUTCH ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING COMPRESSOR - ENGINE ROOM RELAY BLOCK)
E146415E05
  1. Disconnect the D39 compressor connector.

  1. Remove the magnet clutch relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D39-3 (MG+) - Engine room relay block magnet clutch relay terminal 3
    Always
    Below 1 Ω
    D39-3 (MG+) or Engine room relay block magnet clutch relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - BATTERY)
E146416E03
  1. Remove the magnet clutch relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block magnet clutch relay terminal 5 - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)