AIR CONDITIONING SYSTEM > Air Conditioning Compressor Magnetic Clutch Circuit |

| 1.CHECK CAN COMMUNICATION SYSTEM |
Use the intelligent tester to check if the CAN communication system is functioning normally.
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (AIR CONDITIONING SWITCH SIGNAL) |
Use the Data List to check if the air conditioning switch is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| A/C Signal | Air conditioning switch signal / ON or OFF | ON: Air conditioning on OFF: Air conditioning off | - |
|
| ||||
| OK | ||
| ||
| 3.INSPECT FUSE (A/C IG) |
![]() |
Remove the A/C IG fuse from the main body ECU (cowl side junction block LH).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A/C IG fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.INSPECT MAGNET CLUTCH RELAY |
![]() |
Remove the magnet clutch relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | When battery voltage is not applied between terminals | 10 kΩ or higher |
| When battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY) |
![]() |
Disconnect the H24 amplifier connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H24-20 (MGC) - Body ground | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 6.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (MGC VOLTAGE) |
![]() |
Reconnect the H24 amplifier connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H24-20 (MGC) - Body ground | Engine running and air conditioning switch on | Below 1 V |
| Engine running and air conditioning switch off | 11 to 14 V |
|
| ||||
| OK | |
| 7.INSPECT COOLER COMPRESSOR ASSEMBLY (COMPRESSOR HARNESS) |
![]() |
Disconnect the D39 compressor connector.
Disconnect the magnet clutch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (MG+) - 1 | Always | Below 1 Ω |
| 3 (MG+) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.INSPECT MAGNET CLUTCH ASSEMBLY |
Disconnect the magnet clutch connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - Body ground | Always | 3.4 to 3.8 Ω |
When connector terminal 1 is connected to the positive (+) battery terminal, check that the following occurs: 1) the magnet clutch operating sound can be heard, and 2) the magnet clutch hub and rotor lock.
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING COMPRESSOR - ENGINE ROOM RELAY BLOCK) |
![]() |
Disconnect the D39 compressor connector.
Remove the magnet clutch relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D39-3 (MG+) - Engine room relay block magnet clutch relay terminal 3 | Always | Below 1 Ω |
| D39-3 (MG+) or Engine room relay block magnet clutch relay terminal 3 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - BATTERY) |
![]() |
Remove the magnet clutch relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Engine room relay block magnet clutch relay terminal 5 - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | ||
| ||