Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT

FRONT AIR CONDITIONING UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL COOLER EXPANSION VALVE (w/o Cool Box)


    E145026
  1. Sufficiently apply compressor oil to 4 new O-rings and the fitting surface of the hose joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings to the cooler evaporator.

  1. Install the 2 O-rings to the tube and accessory.

  1. Install the cooler expansion valve and the tube and accessory to the evaporator.



    I104462E02
  1. Using a 4 mm hexagon wrench, install the 2 bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

    Install a new butyl, as shown in the illustration.

    Standard:
    Area
    Standard Dimension
    a
    -5 mm (-0.197 in.) to 0 mm (0 in.)

    Text in Illustration 
    *1
    Butyl Tape



2. INSTALL EVAPORATOR TEMPERATURE SENSOR


E146390E01

NOTICE:
If reusing the evaporator, do not insert the sensor into a location where the sensor was previously inserted.

  1. Insert the sensor to a location that is 1 fin to the right or left of its previous location.
    Standard 
    Area
    Standard Dimension
    a
    48 mm (1.89 in.)
    b
    9 mm (0.354 in.)
    c
    34.3 mm (1.35 in.)
    d
    47.7 mm (1.88 in.)
    e
    50 mm (1.97 in.)



3. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY


E145024
  1. Install the evaporator to the blower case.

    HINT:
    If a new cooler evaporator is installed, add compressor oil to the cooler evaporator as follows.

    Compressor oil:
    ND-OIL 8 or equivalent. Add 40 cc (1.35 fl. oz.)



4. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY


I104419
  1. Install the heater radiator unit.



5. INSTALL AIR CONDITIONING RADIATOR ASSEMBLY (w/ Cool Box)


    I105767
  1. Attach the 3 claws to install the air conditioning radiator.

  1. Install the 6 screws.



    I104416
  1. Attach the 3 claws to install the heater clamp.



    I104413
  1. Install the plate with the 3 screws.

  1. Attach the clamp.

  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the hose joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings to the cooler evaporator.



    I105769
  1. Using a 4 mm hexagon wrench, install the air conditioner tube with the 2 hexagon bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

  1. Tighten the 2 screws.



    I105770
  1. Install 2 new packings, as shown in the illustration.

    NOTICE:
    Apply packing without gaps at packing area.



6. INSTALL AIR CONDITIONING RADIATOR ASSEMBLY (w/o Cool Box)


    I105768
  1. Attach the 3 claws to install the air conditioning radiator.

  1. Install the 6 screws.



    I104416
  1. Attach the 3 claws to install the heater clamp.



    I104413
  1. Install the plate with the 3 screws.

  1. Attach the clamp.



    E146153
  1. Install a new packing, as shown in the illustration.



7. INSTALL AIR CONDITIONER TUBE ASSEMBLY (w/ Cool Box)
  1. Sufficiently apply compressor oil to 6 new O-rings and the fitting surface of the hose joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 6 O-rings to the air conditioner tube.



    I105748
  1. Install the air conditioner tube with the screw.



    E112921E01
  1. Connect the air conditioner tube with the 2 piping clamps.

    NOTICE:
    After connection, check the claw engagement of the 2 piping clamps.



8. INSTALL COOLING UNIT DAMPER SERVO SUB-ASSEMBLY


  1. Set the damper servo so that the cutout part engages with the tooth of the gear, and attach the claw to install the damper servo.


    E145030E04


    Text in Illustration 
    *1
    Air Conditioning Unit Side
    *2
    Dumper Servo Side
    *3
    Cutout
    *4
    Tooth



    I104412
  1. Install the 4 screws and connect the 2 connectors.



9. INSTALL BLOWER DAMPER SERVO SUB-ASSEMBLY


I104415
  1. Install the damper servo with the 3 screws.

  1. Connect the connector.



10. INSTALL DAMPER SERVO SUB-ASSEMBLY


I104414
  1. Install the damper servo with the 3 screws.

  1. Connect the connector.



11. INSTALL DAMPER SERVO SUB-ASSEMBLY


E146155
  1. Install the damper servo with the 3 screws, as shown in the illustration.

  1. Connect the connector.



12. INSTALL AIR DUCT


E145015
  1. Install the duct with the 2 screws.



13. INSTALL BLOWER WITH FAN MOTOR SUB-ASSEMBLY


I104411
  1. Install the motor with the 3 screws.



14. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY


I104405
  1. Install the amplifier with the 2 screws.

  1. Connect the connector.



15. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY


I104404
  1. Install the air duct with the screw.



16. INSTALL COOLER AIR HOSE


I104406
  1. Attach the 2 claws to install the cooler air hose.



17. INSTALL AIR REFINER ELEMENT


I104410
  1. Install the air refiner element into the blower case.

    NOTICE:
    Install the air refiner element with its UP marks oriented in the correct direction.



18. INSTALL AIR FILTER COVER PLATE


I104408
  1. Attach the 2 clips to install the air filter cover plate.

    NOTICE:
    Install the air filter cover plate with its UP mark oriented in the correct direction.



19. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY


I104403
  1. Attach the 4 claws to install the air duct.



20. INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY


I104402
  1. Attach the 4 claws to install the nozzle.