Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MAIN BODY ECU

B174142E05

  1. Disconnect the DC, DD, H3, and H4 main body ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    DC-2 (LCTY) - Body ground
    B*1 - Body ground
    G*2 - Body ground
    Rear door courtesy light switch LH signal
    Rear door LH open → closed
    Below 1 Ω → 10 kΩ or higher
    DD-62 (GND1, GND2) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    H3-21 (PCTY) - Body ground
    BE - Body ground
    Front door courtesy light switch RH signal
    Front door RH open → closed
    Below 1 Ω → 10 kΩ or higher
    H3-25 (RRCY) - Body ground
    L - Body ground
    Rear door courtesy light switch RH signal
    Rear door RH open → closed
    Below 1 Ω → 10 kΩ or higher
    H4-24 (DCTY) - Body ground
    BR - Body ground
    Front door courtesy light switch LH signal
    Front door LH open → closed
    Below 1 Ω → 10 kΩ or higher
    *1: w/o Rear Power Seat Control System
    *2: w/ Rear Power Seat Control System
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the DC, DD, H3 and H4 main body ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    DB-13 (BECU) - Body ground
    GR - Body ground
    BECU power supply
    Always
    11 to 14 V
    DD-43 (IG) - Body ground
    LG - Body ground
    IG signal
    Ignition switch off → ON
    Below 1 V → 11 to 14 V
    DD-45 (ACC) - Body ground
    BE - Body ground
    ACC signal
    Ignition switch off → ACC
    Below 1 V → 11 to 14 V
    DD-51 (ILE) - Body ground
    GR - Body ground
    Illuminated entry system operate signal
    Illuminated entry system off → on
    11 to 14 V → Below 1 V
    H2-5 (CANH) - DD-62 (GND1, GND2)
    L - W-B
    CAN communication signal
    Ignition switch ON
    Pulse generation
    (See waveform 1)
    H2-6 (CANL)- DD-62 (GND1, GND2)
    W - W-B
    CAN communication signal
    Ignition switch ON
    Pulse generation
    (See waveform 2)
    H2-10 (LIN2) - DD-62 (GND1, GND2)
    V - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation
    If the result is not as specified, the main body ECU may have a malfunction.



  5. A086154E10
  6. Waveform 1 (Reference): Using an oscilloscope
    CAN Communication Signal 
    Terminal Name
    CANH - GND1, GND2
    Tester Range
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.



  7. A086155E11
  8. Waveform 2 (Reference): Using an oscilloscope
    CAN Communication Signal 
    Terminal Name
    CANL - GND1, GND2
    Tester Range
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.


CHECK BACK DOOR ECU

E157854E01

  1. Disconnect the V2 and V3 back door ECU connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V2-7 (BECU) - Body ground
    GR - Body ground
    Battery power supply
    Always
    11 to 14 V
    V2-8 (SIG) - Body ground
    Y - Body ground
    IG power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    V2-6 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    V3-10 (BDCY) - V3-20 (CTYE)
    P - R
    Back door courtesy light switch signal
    Back door open
    Below 1 Ω
    Back door closed
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the V2 and V3 back door ECU connectors.

  4. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V2-2 (LGLP) - V2-6 (GND)
    LG - W-B
    Illumination signal (to luggage compartment room light assembly)
    Back door closed
    11 to 14 V
    Back door open
    Below 1 V
    V2-16 (MPX1) - V2-6 (GND)
    Y - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation
    V3-20 (CTYE) - V2-6 (GND)
    R - W-B
    Ground for back door courtesy light switch
    Always
    Below 1 Ω
    If the result is not as specified, the back door ECU may be malfunctioning.