LIGHTING SYSTEM > TERMINALS OF ECU |
| CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) |

Disconnect the DD, H2, H3 and H4 main body ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| DD-62 (GND1, GND2) - Body ground | W-B - Body ground | Body ground | Always | Below 1 Ω |
| H2-4 (HAZ) - Body ground | BE - Body ground | Hazard warning signal switch input signal | Hazard warning signal switch OFF → ON | 10 kΩ or higher → Below 1 Ω |
| H3-28 (FFOG) - Body ground* | P - Body ground | Front fog light switch signal | Front fog light switch OFF → ON | 10 kΩ or higher → Below 1 Ω |
| H3-17 (HEAD) - Body ground | W - Body ground | Light control switch HEAD signal | Light control switch HEAD | Below 1 Ω |
| Light control switch except HEAD | 10 kΩ or higher | |||
| H3-21 (PCTY) - Body ground | BE - Body ground | Front door courtesy light switch RH signal | Front door RH open → closed | Below 1 Ω → 10 kΩ or higher |
| H4-21 (A) - Body ground | G - Body ground | Light control switch AUTO signal | Light control switch AUTO | Below 1 Ω |
| Light control switch except AUTO | 10 kΩ or higher | |||
| H4-23 (TAIL) - Body ground | BE - Body ground | Light control switch TAIL signal | Light control switch TAIL | Below 1 Ω |
| Light control switch except TAIL | 10 kΩ or higher | |||
| H4-24 (DCTY) - Body ground | BR - Body ground | Front door courtesy light switch LH signal | Front door LH open → closed | Below 1 Ω → 10 kΩ or higher |
Reconnect the DD, H2, H3, and H4 main body ECU connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| DB-13 (BECU) - Body ground | GR - Body ground | BECU power supply | Always | 11 to 14 V |
| DB-16 (DIM) - Body ground | R - Body ground | Headlight low beam signal | Light control switch HEAD, dimmer switch High | Below 1 V |
| Light control switch HEAD, dimmer switch except High | 11 to 14 V | |||
| DB-18 (HRLY) - Body ground | L - Body ground | Headlight low beam signal | Light control switch HEAD, dimmer switch Low | Below 1 V |
| Light control switch HEAD, dimmer switch except Low | 11 to 14 V | |||
| H2-5 (CANH) - DD-62 (GND1, GND2) | L - W-B | CAN communication signal | Ignition switch ON | Pulse generation (See waveform 1) |
| H2-6 (CANL) - DD-62 (GND1, GND2) | W - W-B | CAN communication signal | Ignition switch ON | Pulse generation (See waveform 2) |
| H4-4 (FFGO) - Body ground* | SB - Body ground | Front fog light signal | Light control switch TAIL, front fog light switch ON | Below 1 V |
| Light control switch TAIL, front fog light switch OFF | 11 to 14 V |
![]() |
Waveform 1 (Reference) : Using an oscilloscope
| Terminal Name | CANH - GND1, GND2 |
| Tester Range | 1 V/DIV., 10 μsec./DIV. |
| Condition | Ignition switch ON |
![]() |
Waveform 2 (Reference) : Using an oscilloscope
| Terminal Name | CANL - GND1, GND2 |
| Tester Range | 1 V/DIV., 10 μsec./DIV. |
| Condition | Ignition switch ON |
| CHECK OUTER MIRROR CONTROL ECU |

Disconnect the M7 and M8 outer mirror control ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| M7-3 (B) - Body ground | R - Body ground | Battery power supply | Always | 11 to 14 V |
| M7-4 (ACC) - Body ground | Y - Body ground | ACC power supply | Ignition switch off → ACC | Below 1 V → 11 to 14 V |
| M7-9 (GND) - Body ground | W-B - Body ground | Body ground | Always | Below 1 Ω |
Reconnect the M7 and M8 outer mirror control ECU connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| M8-1 (CAN) - M7-9 (GND) | LG - W-B | CAN communication signal | Ignition switch ON | Pulse generation (see waveform 1) |
| M8-17 (LP) - Body ground | V - Body ground | Puddle light LH operation signal | Puddle light LH turn on | 11 to 14 V |
| M8-21 (CGND) - M7-9 (GND) | W - W-B | CAN communication signal | Ignition switch ON | Pulse generation (see waveform 2) |
| M8-37 (LP) - Body ground | SB - Body ground | Puddle light RH operation signal | Puddle light RH turn on | 11 to 14 V |
![]() |
Waveform 1 (Reference) : Using an oscilloscope
| Terminal Name | CAN - GND |
| Tester Range | 1 V/DIV., 10 μsec./DIV. |
| Condition | Ignition switch ON |
![]() |
Waveform 2 (Reference) : Using an oscilloscope
| Terminal Name | CGND - GND |
| Tester Range | 1 V/DIV., 10 μsec./DIV. |
| Condition | Ignition switch ON |