Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Headlight Signal Circuit

for Preparation Click here


DESCRIPTION

The main body ECU receives a headlight Lo switch information signal from the light control switch, and illuminates the headlight low beam.

WIRING DIAGRAM


E163640E04


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEADLIGHT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test / Headlight Relay

  1. Check that the headlight (low) turn on/off.

    Main Body ECU 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Headlight Relay
    Headlight
    ON or OFF
    -

    OK:
    Headlight low beams turn on/off.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (HEAD LL, HEAD RL)


    E161570E04
  1. Remove the HEAD LL and HEAD RL fuses from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    HEAD LL fuse
    Always
    Below 1 Ω
    HEAD RL fuse
    Always
    Below 1 Ω

  1. Reinstall the HEAD LL and HEAD RL fuses.



NG
REPLACE FUSE
OK


3.REPLACE HEADLIGHT (LOW) BULB
  1. Temporarily replace the headlight (low) bulb with a new or normally functioning one .

  1. Check that the headlight (low) turn on.

    OK:
    Headlight (low) turn on.



NG
Go to step 4
OK

END 

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LOW BULB - HEAD RELAY)
E146028E03
  1. for LH:

    1. Disconnect the A12 headlight (low) LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A12-2 - Body ground
      Light control switch HEAD, dimmer switch Low
      11 to 14 V
      Light control switch HEAD, dimmer switch except Low
      Below 1 V

    3. Reinstall the headlight (low) LH connector.

  1. for RH:

    1. Disconnect the A13 headlight (low) RH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A13-2 - Body ground
      Light control switch HEAD, dimmer switch Low
      11 to 14 V
      Light control switch HEAD, dimmer switch except Low
      Below 1 V

    3. Reinstall the headlight (low) RH connector.



NG
Go to step 5
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT LOW BULB - BODY GROUND) 

5.INSPECT HEADLIGHT RELAY (HEAD)
A111813E06
  1. Remove the HEAD relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω

  1. Reinstall the HEAD relay.



NG
REPLACE HEAD RELAY
OK


6.CHECK HARNESS AND CONNECTOR (HEAD RELAY - BATTERY)
E147144E06
  1. Remove the HEAD relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    HEAD relay terminal 1 - Body ground
    Always
    11 to 14 V
    HEAD relay terminal 3 - Body ground
    Always
    11 to 14 V

  1. Reinstall the HEAD relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (HEAD RELAY - HEADLIGHT LOW BULB)


    E161597E02
  1. Remove the HEAD relay from the engine room relay block.

  1. for LH:

    1. Disconnect the A12 headlight (low) LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      HEAD relay terminal 5 - A12-2
      Always
      Below 1 Ω
      HEAD relay terminal 5 - Body ground
      Always
      10 kΩ or higher

    3. Reinstall the headlight (low) LH connector.

  1. for RH:

    1. Disconnect the A13 headlight (low) RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      HEAD relay terminal 5 - A13-2
      Always
      Below 1 Ω
      HEAD relay terminal 5 - Body ground
      Always
      10 kΩ or higher

    3. Reinstall the headlight (low) RH connector.

  1. Reinstall the HEAD relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - MAIN BODY ECU)
E147118E02
  1. Disconnect the DB main body ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    DB-18 - Body ground
    Always
    11 to 14 V

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)