LIGHTING SYSTEM > Front Fog Light Circuit |

| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT FOG LIGHT) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Active Test / Front Fog Light.
Check that the front fog lights turn on/off.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Front Fog Light Relay | Front fog light | ON or OFF | - |
|
| ||||
| OK | ||
| ||
| 2.INSPECT FUSE (FOG) |
![]() |
Remove the FOG fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| FOG fuse | Always | Below 1 Ω |
Reinstall the FOG fuse.
|
| ||||
| OK | |
| 3.REPLACE FOG LIGHT BULB |
Temporarily replace the front fog light bulb with a new or normally functioning one .
Check that the front fog light turn on.
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (FRONT FOG LIGHT BULB - BATTERY) |
![]() |
for LH:
Disconnect the A36 front fog light LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A36-2 - Body ground | Light control switch TAIL, front fog light switch ON | 11 to 14 V |
| Light control switch TAIL, front fog light switch OFF | Below 1 V |
Reconnect the front fog light LH connector.
for RH:
Disconnect the A37 front fog light RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A37-2 - Body ground | Light control switch TAIL, front fog light switch ON | 11 to 14 V |
| Light control switch TAIL, front fog light switch OFF | Below 1 V |
Reconnect the front fog light RH connector.
|
| ||||
| OK | ||
| ||
| 5.INSPECT FOG LIGHT RELAY (FOG) |
![]() |
Remove the FOG relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | When battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| When battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
Reinstall the FOG relay.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (FOG RELAY - BATTERY AND TAIL RELAY) |
![]() |
Remove the FOG relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| FOG relay terminal 1 - Body ground | Light control switch TAIL | 11 to 14 V |
| FOG relay terminal 3 - Body ground | Always | 11 to 14 V |
Reinstall the FOG relay.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (FOG RELAY - FRONT FOG LIGHT BULB) |
![]() |
Remove the FOG relay from the engine room relay block.
for LH:
Disconnect the A36 front fog light LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| FOG relay terminal 5 - A36-2 | Always | Below 1 Ω |
| FOG relay terminal 5 - Body ground | Always | 10 kΩ or higher |
Reconnect the front fog light LH connector.
for RH:
Disconnect the A37 front fog light RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| FOG relay terminal 5 - A37-2 | Always | Below 1 Ω |
| FOG relay terminal 5 - Body ground | Always | 10 kΩ or higher |
Reconnect the front fog light RH connector.
Reinstall the FOG relay.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (FOG RELAY - MAIN BODY ECU) |
![]() |
Disconnect the H4 main body ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H4-4 - Body ground | Light control switch TAIL | 11 to 14 V |
Reconnect the main body ECU connector.
|
| ||||
| OK | ||
| ||