LIGHTING SYSTEM > Taillight Circuit |

| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TAILLIGHT) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Active Test / Tail Light
Check that the taillights turn on/off.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Taillight Relay | Taillight | ON or OFF | - |
| Result | Proceed to |
| OK | A |
| NG (All taillights do not turn on) | B |
| NG (Front parking lights and side marker light do not turn on) | C |
| NG (Taillight and license plate light do not turn on) | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 2.INSPECT FUSE (TAIL) |
![]() |
Remove the TAIL fuse from the main body ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| TAIL fuse | Always | Below 1 Ω |
Reinstall the TAIL fuse.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY) |
![]() |
Disconnect the DA main body ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| DA-1 - Body ground | Always | 11 to 14 V |
Reconnect the main body ECU connector.
|
| ||||
| OK | ||
| ||
| 4.CHECK VEHICLE CONDITION |
Check vehicle condition.
| Result | Proceed to |
| Front parking light and side marker light do not turn on | A |
| Front parking light does not turn on | B |
| Side marker light does not turn on | C |
|
| ||||
|
| ||||
| A | |
| 5.INSPECT MAIN BODY ECU |
![]() |
Remove the main body ECU with its connector still connected.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| DB-8 - Body Ground | Light control switch OFF → TAIL | Below 1 V → 11 to 14 V |
Reinstall the main body ECU.
|
| ||||
| OK | ||
| ||
| 6.REPLACE FRONT PARKING LIGHT BULB |
Temporarily replace the front parking light bulb with a new or normally functioning one .
Check that the front parking light turn on.
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (FRONT PARKING LIGHT - BODY GROUND) |
![]() |
for LH
Disconnect the A15 front parking light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A15-2 (E) - Body Ground | Always | Below 1 Ω |
Reconnect the front parking light connector.
for RH
Disconnect the A16 front parking light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A16-2 (E) - Body Ground | Always | Below 1 Ω |
Reconnect the front parking light connector.
|
| ||||
| OK | ||
| ||
| 8.REPLACE SIDE MARKER LIGHT BULB |
Temporarily replace the side marker light bulb with a new or normally functioning one .
Check that the side marker light turn on.
|
| ||||
| OK | ||
| ||
| 9.CHECK HARNESS AND CONNECTOR (SIDE MARKER LIGHT - BODY GROUND) |
![]() |
for LH
Disconnect the A39 side marker light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A39-1 - Body Ground | Always | Below 1 Ω |
Reconnect the side marker light connector.
for RH
Disconnect the A38 front parking light connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A38-1 - Body Ground | Always | Below 1 Ω |
Reconnect the front turn signal light connector.
|
| ||||
| OK | ||
| ||
| 10.CHECK VEHICLE CONDITION |
Check vehicle condition.
| Result | Proceed to |
| Taillight and license plate light does not turn on | A |
| Taillight (for Rear combination light) does not turn on | B |
| Taillight (for Rear light) does not turn on | C |
| License plate light does not turn on | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 11.INSPECT MAIN BODY ECU |
![]() |
Remove the main body ECU with its connector still connected.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| DC-22 - Body Ground | Light control switch OFF → TAIL | Below 1 V → 11 to 14 V |
Reinstall the main body ECU.
|
| ||||
| OK | ||
| ||
| 12.REPLACE REAR COMBINATION LIGHT BULB (TAILLIGHT BULB) |
Temporarily replace the rear combination light (taillight) bulb with a new or normally functioning one .
Check that the rear combination light (taillight) turn on.
|
| ||||
| OK | ||
| ||
| 13.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT (TAILLIGHT) - BODY GROUND) |
![]() |
for LH:
Disconnect the O21 rear combination light LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O21-1 (E) - Body ground | Always | Below 1 Ω |
Reconnect the rear combination light LH connector.
for RH:
Disconnect the O20 rear combination light RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O20-1 (E) - Body ground | Always | Below 1 Ω |
Reconnect the rear combination light RH connector.
|
| ||||
| OK | ||
| ||
| 14.REPLACE REAR LIGHT (TAILLIGHT BULB) |
Temporarily replace the rear light (taillight) bulb with a new or normally functioning one .
Check that the rear light (taillight) turn on.
|
| ||||
| OK | ||
| ||
| 15.CHECK HARNESS AND CONNECTOR (REAR LIGHT (TAILLIGHT) - BODY GROUND) |
![]() |
for LH:
Disconnect the V8 rear light LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| V8-3 (E) - Body ground | Always | Below 1 Ω |
Reconnect the rear light LH connector.
for RH:
Disconnect the V7 rear light RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| V7-3 (E) - Body ground | Always | Below 1 Ω |
Reconnect the rear light RH connector.
|
| ||||
| OK | ||
| ||
| 16.REPLACE LICENSE PLATE LIGHT BULB |
Temporarily replace the license plate light bulb with a new or normally functioning one .
Check that the license plate light turns on.
|
| ||||
| OK | ||
| ||
| 17.CHECK HARNESS AND CONNECTOR (LICENSE PLATE LIGHT - BODY GROUND) |
![]() |
Disconnect the V9 license plate light LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| V9-1 (E) - Body ground | Always | Below 1 Ω |
Reconnect the license plate light connector.
Reconnect the license plate light connector.
|
| ||||
| OK | ||
| ||