Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Taillight Circuit

for Preparation Click here


DESCRIPTION

The main body ECU receives a light control switch information signal from the headlight dimmer switch, and illuminates the taillights.

WIRING DIAGRAM


E161599E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TAILLIGHT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test / Tail Light

  1. Check that the taillights turn on/off.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Taillight Relay
    Taillight
    ON or OFF
    -

    OK:
    Taillights turn on/off.


Result 
Result
Proceed to
OK
A
NG (All taillights do not turn on)
B
NG (Front parking lights and side marker light do not turn on)
C
NG (Taillight and license plate light do not turn on)
D


B
Go to step 2

C
Go to step 4

D
Go to step 10
A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (TAIL)


    E160643E07
  1. Remove the TAIL fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    TAIL fuse
    Always
    Below 1 Ω

  1. Reinstall the TAIL fuse.



NG
REPLACE FUSE
OK


3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY)
E147142E01
  1. Disconnect the DA main body ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    DA-1 - Body ground
    Always
    11 to 14 V

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) 

4.CHECK VEHICLE CONDITION
  1. Check vehicle condition.

    Result 
    Result
    Proceed to
    Front parking light and side marker light do not turn on
    A
    Front parking light does not turn on
    B
    Side marker light does not turn on
    C



B
Go to step 6

C
Go to step 8
A


5.INSPECT MAIN BODY ECU


    E162308E01
  1. Remove the main body ECU with its connector still connected.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    DB-8 - Body Ground
    Light control switch
    OFF → TAIL
    Below 1 V → 11 to 14 V

  1. Reinstall the main body ECU.



NG
REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - PARKING LIGHT AND SIDE MARKER LIGHT) 

6.REPLACE FRONT PARKING LIGHT BULB
  1. Temporarily replace the front parking light bulb with a new or normally functioning one .

  1. Check that the front parking light turn on.

    OK:
    Front parking light turn on.



NG
Go to step 7
OK

END 

7.CHECK HARNESS AND CONNECTOR (FRONT PARKING LIGHT - BODY GROUND)
E161602E01
  1. for LH

    1. Disconnect the A15 front parking light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A15-2 (E) - Body Ground
      Always
      Below 1 Ω

    3. Reconnect the front parking light connector.

  1. for RH

    1. Disconnect the A16 front parking light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A16-2 (E) - Body Ground
      Always
      Below 1 Ω

    3. Reconnect the front parking light connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - PARKING LIGHT) 

8.REPLACE SIDE MARKER LIGHT BULB
  1. Temporarily replace the side marker light bulb with a new or normally functioning one .

  1. Check that the side marker light turn on.

    OK:
    Side marker light turn on.



NG
Go to step 9
OK

END 

9.CHECK HARNESS AND CONNECTOR (SIDE MARKER LIGHT - BODY GROUND)
E161603E01
  1. for LH

    1. Disconnect the A39 side marker light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A39-1 - Body Ground
      Always
      Below 1 Ω

    3. Reconnect the side marker light connector.

  1. for RH

    1. Disconnect the A38 front parking light connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A38-1 - Body Ground
      Always
      Below 1 Ω

    3. Reconnect the front turn signal light connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - SIDE MARKER LIGHT) 

10.CHECK VEHICLE CONDITION
  1. Check vehicle condition.

    Result 
    Result
    Proceed to
    Taillight and license plate light does not turn on
    A
    Taillight (for Rear combination light) does not turn on
    B
    Taillight (for Rear light) does not turn on
    C
    License plate light does not turn on
    D



B
Go to step 12

C
Go to step 14

D
Go to step 16
A


11.INSPECT MAIN BODY ECU


    E162307E01
  1. Remove the main body ECU with its connector still connected.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    DC-22 - Body Ground
    Light control switch
    OFF → TAIL
    Below 1 V → 11 to 14 V

  1. Reinstall the main body ECU.



NG
REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - TAILLIGHTS, LICENSE PLATE LIGHT) 

12.REPLACE REAR COMBINATION LIGHT BULB (TAILLIGHT BULB)
  1. Temporarily replace the rear combination light (taillight) bulb with a new or normally functioning one .

  1. Check that the rear combination light (taillight) turn on.

    OK:
    Rear combination light (taillight) turn on.



NG
Go to step 13
OK

END 

13.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT (TAILLIGHT) - BODY GROUND)
E161604E01
  1. for LH:

    1. Disconnect the O21 rear combination light LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      O21-1 (E) - Body ground
      Always
      Below 1 Ω

    3. Reconnect the rear combination light LH connector.

  1. for RH:

    1. Disconnect the O20 rear combination light RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      O20-1 (E) - Body ground
      Always
      Below 1 Ω

    3. Reconnect the rear combination light RH connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - REAR COMBINATION LIGHT (TAILLIGHT)) 

14.REPLACE REAR LIGHT (TAILLIGHT BULB)
  1. Temporarily replace the rear light (taillight) bulb with a new or normally functioning one .

  1. Check that the rear light (taillight) turn on.

    OK:
    Rear light (taillight) turn on.



NG
Go to step 15
OK

END 

15.CHECK HARNESS AND CONNECTOR (REAR LIGHT (TAILLIGHT) - BODY GROUND)
E161605E01
  1. for LH:

    1. Disconnect the V8 rear light LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      V8-3 (E) - Body ground
      Always
      Below 1 Ω

    3. Reconnect the rear light LH connector.

  1. for RH:

    1. Disconnect the V7 rear light RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      V7-3 (E) - Body ground
      Always
      Below 1 Ω

    3. Reconnect the rear light RH connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - REAR LIGHT (TAILLIGHT)) 

16.REPLACE LICENSE PLATE LIGHT BULB
  1. Temporarily replace the license plate light bulb with a new or normally functioning one .

  1. Check that the license plate light turns on.

    OK:
    License plate light turns on.



NG
Go to step 17
OK

END 

17.CHECK HARNESS AND CONNECTOR (LICENSE PLATE LIGHT - BODY GROUND)
E161606E01
  1. Disconnect the V9 license plate light LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V9-1 (E) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the license plate light connector.

    1. Reconnect the license plate light connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - LICENSE PLATE LIGHT)