LIGHTING SYSTEM > Illumination Circuit |


| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ILLUMINATION LIGHT) |
Connect the intelligent tester to DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Turn the room light switch to the DOOR position.
All doors closed (courtesy light switches OFF).
Enter the following menus: Body / Main Body / Active Test / Illuminated Entry System.
Check the illumination lights while operating the main body ECU using the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Illuminated Entry System | Illumination light | ON or OFF | - |
| Result | Proceed to |
| OK | A |
| NG (All lights do not turn on) | B |
| NG (Only ignition key cylinder light does not turn on) | C |
| NG (Only foot light does not turn on) | D |
| NG (Room lights do not turn on) | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 2.INSPECT FUSE (DOME) |
![]() |
Remove the DOME fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| DOME fuse | Always | Below 1 Ω |
Reinstall the DOME.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (DOME FUSE - MAIN BODY ECU) |
![]() |
Disconnect the DD main body ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| DD-51 (ILE) - Body ground | Always | 11 to 14 V |
Reconnect the main body ECU connector.
|
| ||||
| OK | ||
| ||
| 4.INSPECT TRANSPONDER KEY AMPLIFIER (IGNITION KEY CYLINDER LIGHT) |
![]() |
Remove the transponder key amplifier (ignition key cylinder light) (Click here).
Apply battery voltage and then check that the light turns on.
| Measurement Condition | Specified Condition |
| Positive battery → 2 (ILL+) negative battery → 6 (ILL-) | Ignition key cylinder light turns on. |
Reinstall the transponder key amplifier (ignition key cylinder light).
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (IGNITION KEY CYLINDER LIGHT - BATTERY) |
![]() |
Disconnect the H27 transponder key amplifier (ignition key cylinder light) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H27-2 (ILL+) - Body ground | Always | 11 to 14 V |
Reconnect the transponder key amplifier (ignition key cylinder light) connector.
|
| ||||
| OK | ||
| ||
| 6.INSPECT FOOT LIGHT |
![]() |
Remove the foot light (Click here).
Apply battery voltage and then check that the light turns on.
| Measurement Condition | Specified Condition |
| Positive battery → 1 negative battery → 2 | Foot light turns on. |
Reinstall the foot light.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (FOOT LIGHT - BATTERY) |
![]() |
Disconnect the H60 foot light connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H60-1 - Body ground | Always | 11 to 14 V |
Reconnect the foot light connector.
|
| ||||
| OK | ||
| ||
| 8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ILLUMINATED ENTRY) |
Connect the intelligent tester to DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Turn the room light switch DOOR position.
All doors closed (courtesy light switches OFF).
Enter the following menus: Body / Main Body / Active Test / Illuminated Entry System.
Check the illumination lights while operating the main body ECU using the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Illuminated Entry System | Illumination light | ON or OFF | - |
| Result | Proceed to |
| NG (All room lights do not turn on) | A |
| NG (Personal light does not turn on) | B |
| NG (No. 1 room light does not turn on) | C |
| NG (No. 2 room light does not turn on) | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 9.INSPECT INTERIOR DOME LIGHT SWITCH ASSEMBLY |
![]() |
Remove the interior dome light switch assembly (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 5 (FCTY) - 10 (FLMP) | interior room light switch DOOR | Below 1 Ω |
Reinstall the interior room light switch assembly.
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (ROOM LIGHTS - INTERIOR DOME LIGHT SWITCH ASSEMBLY) |
![]() |
Disconnect the J7 interior dome light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J7-10 (FLMP) - Body ground | Room light switch DOOR | 11 to 14 V |
Reconnect the interior dome light switch assembly connector.
|
| ||||
| OK | ||
| ||
| 11.INSPECT ROOF CONSOLE BOX ASSEMBLY (PERSONAL LIGHT) |
![]() |
Remove the roof console box assembly.
Roof console box (personal light) switch is DOOR position.
Apply battery voltage and then check that the light turns on.
| Measurement Condition | Specified Condition |
| Positive battery → 2 (B) negative battery → 1 (CTY) | Personal light turns on. |
| Result | Proceed to |
| OK | A |
| NG (for Short Type Roof Console Box) | B |
| NG (for Long Type Roof Console Box) | C |
Reinstall the roof console box assembly.
|
| ||||
|
| ||||
| A | |
| 12.CHECK HARNESS AND CONNECTOR (ROOF CONSOLE BOX ASSEMBLY - DOME FUSE) |
![]() |
Disconnect the U7 roof console box assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| U7-2 (B) - Body ground | Always | 11 to 14 V |
Reconnect the roof console box assembly connector.
|
| ||||
| OK | ||
| ||
| 13.INSPECT NO. 1 ROOM LIGHT ASSEMBLY |
![]() |
Remove the No. 1 room light assembly.
No. 1 room light switch is DOOR position.
Apply battery voltage and then check that the light turns on.
| Measurement Condition | Specified Condition |
| Positive battery → 1 (B) negative battery → 3 (CTY) | No. 1 room light turns on. |
| Measurement Condition | Specified Condition |
| Positive battery → 1 (B) negative battery → 3 (CTY) | No. 1 room light turns on. |
| Result | Proceed to |
| OK | A |
| NG (w/o Rear Seat Entertainment System) | B |
| NG (w/ Rear Seat Entertainment System) | C |
Reinstall the No. 1 room light assembly.
|
| ||||
|
| ||||
| A | |
| 14.CHECK HARNESS AND CONNECTOR (NO. 1 ROOM LIGHT ASSEMBLY - DOME FUSE) |
![]() |
Disconnect the U6*1 or U8*2 No. 1 room light assembly connector.
*1: w/o Rear Seat Entertainment System
*2: w/ Rear Seat Entertainment System
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| U6-1 (B) - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| U8-1 (B) - Body ground | Always | 11 to 14 V |
Reconnect the No. 1 room light assembly connector.
|
| ||||
| OK | ||
| ||
| 15.INSPECT NO. 2 ROOM LIGHT ASSEMBLY |
![]() |
Remove the No. 2 room light assembly .
No. 2 room light switch is OFF position.
Apply battery voltage and then check that the light turns on.
| Measurement Condition | Specified Condition |
| Positive battery → 1 (B) negative battery → 3 (CTY) | No. 2 room light turns on. |
Reinstall the No. 2 room light assembly.
|
| ||||
| OK | |
| 16.CHECK HARNESS AND CONNECTOR (NO. 2 ROOM LIGHT ASSEMBLY - DOME FUSE) |
![]() |
Disconnect the U9 No. 2 room light assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| U9-1 (B) - Body ground | Always | 11 to 14 V |
Reconnect the No. 2 room light assembly connector.
|
| ||||
| OK | ||
| ||