Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Data List.

  5. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Unlock Warning SW
    Unlock warning switch signal / ON or OFF
    ON: Key is in ignition key cylinder
    OFF: No key is in ignition key cylinder
    -
    ACC SW
    Ignition switch signal / ON or OFF
    ON: Ignition switch ACC
    OFF: Ignition switch off
    -
    IG SW
    Ignition switch signal / ON or OFF
    ON: Ignition switch ON
    OFF: Ignition switch ACC or off
    -
    D Door Courtesy SW
    Front door courtesy light switch LH signal / ON or OFF
    ON: Front door courtesy light switch LH ON
    OFF: Front door courtesy light switch LH OFF
    -
    P Door Courtesy SW
    Front door courtesy light switch RH signal / ON or OFF
    ON: Front door courtesy light switch RH ON
    OFF: Front door courtesy light switch RH OFF
    -
    RL Door Courtesy SW
    Rear door courtesy light switch LH signal / ON or OFF
    ON: Rear door courtesy light switch LH ON
    OFF: Rear door courtesy light switch LH OFF
    -
    RR Door Courtesy SW
    Rear door courtesy light switch RH signal / ON or OFF
    ON: Rear door courtesy light switch RH ON
    OFF: Rear door courtesy light switch RH OFF
    -
    Door Lock SW-Lock
    Door control switch lock signal / ON or OFF
    ON: Door control switch is pushed to LOCK
    OFF: Door control switch is not pushed to LOCK
    -
    Door Lock SW-Unlock
    Door control switch lock signal / ON or OFF
    ON: Door control switch is pushed to UNLOCK
    OFF: Door control switch is not pushed to UNLOCK
    -
    Illumination Rate Info
    Illumination rate / min.: 0, max.: 99.99
    Actual illumination rate is displayed
    -
    I/L ON W/Door Key Unlock
    Interior light ON with unlock / ON or OFF
    Customize setting displayed
    -
    Lighting Time
    Lighting Time / 7.5s or 15s or 30s
    Customize setting displayed
    -
    I/L when ACC OFF
    I/L ON/ACC OFF Light the I/L when ACC OFF/ON or OFF
    Customize setting displayed
    -
    Sensitivity
    Turn on luminous intensity / DARK1, DARK2, NORMAL, LIGHT1, LIGHT2
    Customize setting displayed
    -
    Disp Ex ON Sen
    Display extinction luminous intensity / DARK1, DARK2, NORMAL, LIGHT1, LIGHT2
    Customize setting displayed
    -
    Disp Ex OFF Sen
    Display extinction release luminous intensity / DARK1, DARK2, NORMAL, LIGHT1, LIGHT2
    Customize setting displayed
    -

    Back Door P/W 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Courtesy Switch
    Back door courtesy light switch LH signal / ON or OFF
    ON: Back door courtesy light switch ON
    OFF: Back door courtesy light switch OFF
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Illuminated Entry System
    Illumination light
    ON or OFF
    -
    Taillight Relay
    Taillight Relay
    ON or OFF
    -

    Back Door P/W 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Luggage Compartment Light
    Luggage Compartment Light
    ON or OFF
    -