Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Headlight (HI-BEAM) Circuit

for Preparation Click here


DESCRIPTION

The main body ECU receives light control switch and dimmer switch information signals from the headlight dimmer switch, and illuminates the headlight high beam.

WIRING DIAGRAM


E163640E03


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEADLIGHT [HIGH])
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test / Head Light Hi

  1. Check that the headlight (high) turns on/off.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Head Light Hi
    Headlight (High)
    ON or OFF
    -

    OK:
    Headlight (High) turns on/off.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (HEAD LH, HEAD RH)


    E161570E02
  1. Remove the HEAD LH and HEAD RH fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    HEAD LH fuse
    Always
    Below 1 Ω
    HEAD RH fuse
    Always
    Below 1 Ω

  1. Reinstall the HEAD LH and HEAD RH fuses.



NG
REPLACE FUSE
OK


3.REPLACE HEADLIGHT (HIGH) BULB
  1. Temporarily replace the headlight (high) bulb with a new or normally functioning one .

  1. Check that the headlight (high) come on.

    OK:
    Headlight (high) come on.



NG
Go to step 4
OK

END 

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT [HIGH] BULB - HEADLIGHT DIMMER RELAY)
E146024E05
  1. for LH:

    1. Disconnect the A10 headlight (high) LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A10-2 - Body ground
      Light control switch HEAD, dimmer switch High
      11 to 14 V
      Light control switch HEAD, dimmer switch except High
      Below 1 V

    3. Reconnect the headlight (high) LH connector.

  1. for RH:

    1. Disconnect the A11 headlight (high) RH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A11-2 - Body ground
      Light control switch HEAD, dimmer switch High
      11 to 14 V
      Light control switch HEAD, dimmer switch except High
      Below 1 V

    3. Reconnect the headlight (high) RH connector.



NG
Go to step 5
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT HIGH BULB - BODY GROUND) 

5.INSPECT HEADLIGHT DIMMER RELAY (DIM)
A111813E06
  1. Remove the DIM relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω

  1. Reinstall the DIM relay.



NG
REPLACE DIM RELAY
OK


6.CHECK HARNESS AND CONNECTOR (DIM RELAY - HEAD RELAY)
E147138E03
  1. Remove the DIM relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    DIM relay terminal 1 - Body ground
    Light control switch HEAD, dimmer switch Low
    11 to 14 V
    DIM relay terminal 3 - Body ground
    Light control switch HEAD, dimmer switch Low
    11 to 14 V

  1. Reinstall the DIM relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (DIM RELAY - HEADLIGHT [HIGH] BULB)


    E161593E02
  1. Remove the DIM relay from the engine room relay block.

  1. for LH:

    1. Disconnect the A10 headlight (high) LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      DIM relay terminal 5 - A10-2
      Always
      Below 1 Ω
      DIM relay terminal 5 - Body ground
      Always
      10 kΩ or higher

    3. Reconnect the headlight (high) LH connector.

  1. for RH:

    1. Disconnect the A11 headlight (high) RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      DIM relay terminal 5 - A11-2
      Always
      Below 1 Ω
      DIM relay terminal 5 - Body ground
      Always
      10 kΩ or higher

    3. Reconnect the headlight (high) RH connector.

  1. Reinstall the DIM relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (DIM RELAY - MAIN BODY ECU)
E147118E08
  1. Disconnect the DB main body ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    DB-16 - Body ground
    Light control switch HEAD
    11 to 14 V

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)