LIGHTING SYSTEM > Luggage Room Light Circuit |

| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (LUGGAGE COMPARTMENT LIGHT) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body Electrical / Back Door P/W / Active Test / Luggage Compartment Light.
According to the display on the intelligent tester, check the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Luggage Compartment Light | Luggage Compartment Light | ON or OFF | Luggage Compartment Light switch is DOOR |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (BACK DOOR COURTESY SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Back Door P/W / Data List / Back Door Courtesy Switch.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Back Door Courtesy Switch | Back Door Courtesy Switch / ON or OFF | ON: Back door opened OFF: Back door closed | - |
|
| ||||
| OK | ||
| ||
| 3.INSPECT BACK DOOR LOCK ASSEMBLY (BACK DOOR COURTESY LIGHT SWITCH) |
![]() |
Disconnect the V5 back door lock assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (E) - 4 (S) | Back door closed | 10 kΩ or higher |
| Back door opened | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| 3 (E) - 6 (S) | Back door closed | 10 kΩ or higher |
| Back door opened | Below 1 Ω |
Reconnect the back door lock assembly connector.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - BACK DOOR ECU) |
![]() |
Disconnect the V5 back door lock assembly connector.
Disconnect the V3 back door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| V3-10 (BDCY) - V5-4 (S) | Always | Below 1 Ω |
| V3-20 (CTYE) - V5-3 (E) | Always | Below 1 Ω |
| V5-3 (E) - Body ground | Always | 10 kΩ or higher |
| V5-4 (S) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| V3-10 (BDCY) - V5-6 (S) | Always | Below 1 Ω |
| V3-20 (CTYE) - V5-3 (E) | Always | Below 1 Ω |
| V5-6 (S) - Body ground | Always | 10 kΩ or higher |
| V5-3 (E) - Body ground | Always | 10 kΩ or higher |
Reconnect the back door ECU connector.
Reconnect the back door lock assembly connector.
|
| ||||
| OK | ||
| ||
| 5.INSPECT FUSE (DOME) |
![]() |
Remove the DOME fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| DOME fuse | Always | Below 1 Ω |
Reinstall the DOME fuse.
|
| ||||
| OK | |
| 6.INSPECT LUGGAGE COMPARTMENT ROOM LIGHT |
![]() |
Remove the luggage compartment room light assembly (Click here).
Apply battery voltage and check that the room light comes on.
| Measurement Condition | Switch Condition | Specified Condition |
| Battery positive (+) →1 (B) Battery negative (-) → 3 (E) | Luggage compartment light switch ON | Room light comes on |
| Luggage compartment light switch DOOR | Room light turns off | |
| Luggage compartment light switch OFF | Room light turns off | |
| Battery positive (+) →1 (B) Battery negative (-) → 2 (CTY) | Luggage room light switch ON | Room light turns off |
| Luggage compartment light switch DOOR | Room light comes on | |
| Luggage compartment light switch OFF | Room light turns off |
Reinstall the luggage compartment room light assembly.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT LIGHT - BATTERY AND BACK DOOR ECU) |
![]() |
Disconnect the U10 luggage compartment light assembly connector.
Disconnect the V2 back door ECU connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| U10-1 (B) - Body ground | Always | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| U10-2 (CTY) - V2-2 (LGLP) | Always | Below 1 Ω |
| U10-3 (E) - Body ground | Always | 10 kΩ or higher |
Reconnect the back door ECU connector.
Reconnect the luggage compartment light assembly connector.
|
| ||||
| OK | ||
| ||