Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Luggage Room Light Circuit

for Preparation Click here


DESCRIPTION

The back door ECU receives a luggage compartment light information signal from the back door courtesy light switch, and illuminates the luggage compartment light.

WIRING DIAGRAM


E176429E03


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (LUGGAGE COMPARTMENT LIGHT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body Electrical / Back Door P/W / Active Test / Luggage Compartment Light.

  1. According to the display on the intelligent tester, check the Active Test.

    Back Door P/W 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Luggage Compartment Light
    Luggage Compartment Light
    ON or OFF
    Luggage Compartment Light switch is DOOR

    OK:
    Luggage Compartment light turns on/off.



NG
Go to step 5
OK


2.READ VALUE USING INTELLIGENT TESTER (BACK DOOR COURTESY SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Back Door P/W / Data List / Back Door Courtesy Switch.

  1. According to the display on the intelligent tester, read the Data List.

    Back Door P/W 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Courtesy Switch
    Back Door Courtesy Switch / ON or OFF
    ON: Back door opened
    OFF: Back door closed
    -

    OK:
    When back door courtesy switch operation is performed, the results are the same as above.



NG
Go to step 3
OK

REPLACE BACK DOOR ECU  

3.INSPECT BACK DOOR LOCK ASSEMBLY (BACK DOOR COURTESY LIGHT SWITCH)


    E161579E02
  1. Disconnect the V5 back door lock assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o Power Back Door 
    Tester Connection
    Condition
    Specified Condition
    3 (E) - 4 (S)
    Back door closed
    10 kΩ or higher
    Back door opened
    Below 1 Ω
    w/ Power Back Door 
    Tester Connection
    Condition
    Specified Condition
    3 (E) - 6 (S)
    Back door closed
    10 kΩ or higher
    Back door opened
    Below 1 Ω

  1. Reconnect the back door lock assembly connector.



NG
REPLACE BACK DOOR LOCK ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - BACK DOOR ECU)


    E161580E03
  1. Disconnect the V5 back door lock assembly connector.

  1. Disconnect the V3 back door ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o Power Back Door 
    Tester Connection
    Condition
    Specified Condition
    V3-10 (BDCY) - V5-4 (S)
    Always
    Below 1 Ω
    V3-20 (CTYE) - V5-3 (E)
    Always
    Below 1 Ω
    V5-3 (E) - Body ground
    Always
    10 kΩ or higher
    V5-4 (S) - Body ground
    Always
    10 kΩ or higher
    w/ Power Back Door 
    Tester Connection
    Condition
    Specified Condition
    V3-10 (BDCY) - V5-6 (S)
    Always
    Below 1 Ω
    V3-20 (CTYE) - V5-3 (E)
    Always
    Below 1 Ω
    V5-6 (S) - Body ground
    Always
    10 kΩ or higher
    V5-3 (E) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the back door ECU connector.

  1. Reconnect the back door lock assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK DOOR ECU  

5.INSPECT FUSE (DOME)


    E161570E01
  1. Remove the DOME fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DOME fuse
    Always
    Below 1 Ω

  1. Reinstall the DOME fuse.



NG
REPLACE FUSE
OK


6.INSPECT LUGGAGE COMPARTMENT ROOM LIGHT


    E161581E01
  1. Remove the luggage compartment room light assembly (Click here).

  1. Apply battery voltage and check that the room light comes on.

    Standard Resistance:
    Measurement Condition
    Switch Condition
    Specified Condition
    Battery positive (+) →1 (B)
    Battery negative (-) → 3 (E)
    Luggage compartment light switch ON
    Room light comes on
    Luggage compartment light switch DOOR
    Room light turns off
    Luggage compartment light switch OFF
    Room light turns off
    Battery positive (+) →1 (B)
    Battery negative (-) → 2 (CTY)
    Luggage room light switch ON
    Room light turns off
    Luggage compartment light switch DOOR
    Room light comes on
    Luggage compartment light switch OFF
    Room light turns off

  1. Reinstall the luggage compartment room light assembly.



NG
REPLACE LUGGAGE COMPARTMENT ROOM LIGHT (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (LUGGAGE COMPARTMENT LIGHT - BATTERY AND BACK DOOR ECU)


    E161582E01
  1. Disconnect the U10 luggage compartment light assembly connector.

  1. Disconnect the V2 back door ECU connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    U10-1 (B) - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    U10-2 (CTY) - V2-2 (LGLP)
    Always
    Below 1 Ω
    U10-3 (E) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the back door ECU connector.

  1. Reconnect the luggage compartment light assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK DOOR ECU