Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat)

FRONT SEAT ASSEMBLY (for Manual Seat) > DISASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below are for the LH side.



1. REMOVE OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)


    B194815
  1. Disconnect the connector from the occupant classification ECU.

  1. Detach the claw and remove the occupant classification ECU.



2. REMOVE VERTICAL SEAT ADJUSTER KNOB CAP (for Driver Side)


    B190969
  1. Using a screwdriver, detach the 2 claws and remove the vertical adjuster handle cap.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE VERTICAL ADJUSTING HANDLE LH (for Driver Side)


    B190970
  1. Remove the 2 screws and vertical adjusting handle.



4. REMOVE VERTICAL SEAT ADJUSTER KNOB (for Driver Side)


    B190971
  1. Using a screwdriver, remove the snap ring and vertical seat adjuster knob.

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH (for Driver Side)


    B190972
  1. Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the release handle.

    HINT:
    Tape the screwdriver tip before use.



6. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH (for Front Passenger Side)


    B165802
  1. Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the release handle.

    HINT:
    Tape the screwdriver tip before use.



7. REMOVE FRONT SEAT CUSHION SHIELD LH (for Driver Side)


    B190973
  1. Remove the 2 hog rings and rubber bands of the seatback cover from the seat frame.



    B190974E01
  1. Remove the 3 screws.

  1. Detach 3 claws in the order shown in the illustration, and then remove the front seat cushion shield.

  1. Detach the wire harness clamp and disconnect the connector.



8. REMOVE FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side)


    B200257
  1. Remove the 2 hog rings and rubber bands of the seatback cover from the seat frame.



    B165809E01
  1. Remove the 2 screws.

  1. Detach the 3 claws in the order shown in the illustration, and then remove the front seat cushion shield.



9. REMOVE FRONT POWER SEAT LUMBAR SWITCH (for Driver Side)


    B194037
  1. Disconnect the connector.

  1. Remove the 2 screws and front power seat lumbar switch.



10. REMOVE FRONT SEAT CUSHION SHIELD INNER LH


    B190975E01
  1. Remove the screw.

  1. Detach the 3 claws in the order shown in the illustration, and then remove the front seat cushion shield.

  1. Detach the wire harness clamp.



11. REMOVE SEAT POSITION AIRBAG SENSOR


    B194811
  1. Disconnect the connector from the seat position airbag sensor.

  1. Using T30 "TORX" socket wrench, remove the screw and the seat position airbag sensor.

  1. Remove the seat slide position sensor protector from the seat position airbag sensor.



12. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH


    B191249
  1. Disconnect the connector and detach the 5 clamps.



    B191255
  1. Remove the nut and front seat inner belt LH.



13. REMOVE SEAT CUSHION COVER WITH PAD (for Driver Side)


    B190976
  1. Using a clip remover, remove the 2 clips.



    B190977
  1. Detach the 8 wire harness clamps.



    B194818
  1. Remove the 2 hog rings.



    B195207
  1. Detach the wire harness clamp.



    B190980
  1. Bend the 2 seat frame claws upward.

  1. Detach the hooks and remove the seat cushion cover with pad.



14. REMOVE SEAT CUSHION COVER WITH PAD (for Front Passenger Side)


    B190978
  1. Using a clip remover, remove the 2 clips.



    B190979
  1. Detach the 3 wire harness clamps.



    B194819
  1. Remove the 2 hog rings.



    B190981
  1. Bend the 2 seat frame claws upward.

  1. Detach the hooks and remove the seat cushion cover with pad.



15. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER


    B191005
  1. Remove the 10 hog rings and seat cushion cover.



16. REMOVE FRONT SEAT HEADREST SUPPORT


    B190982
  1. Remove the 3 hog rings.



    B190983
  1. Detach the hooks.



    B190984
  1. Remove the 2 hog rings and seatback cover wires.



    B191055
  1. Detach the 4 claws and remove the 2 front seat headrest supports.



17. REMOVE SEATBACK COVER WITH PAD


    B190986
  1. Lift the seatback cover and remove the nut and seatback cover bracket from the seat frame.

  1. Lift the seatback cover and remove the 4 hog rings and seatback cover with pad.



18. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    B190987
  1. Remove the 2 hog rings and seatback cover wires.



    B165535
  1. Detach the seatback cover bracket from the seatback pad.



    B190988
  1. Remove the 2 hog rings and seatback cover from the seatback pad.



19. REMOVE RECLINING ADJUSTER INSIDE COVER LH


    B191058
  1. Remove the screw and reclining adjuster inside cover.



20. REMOVE RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedure for the LH side and RH side.



21. REMOVE FRONT SEATBACK SHIELD LH


    B200256
  1. Remove the screw.

  1. Detach the claw and remove the front seatback shield.



22. REMOVE FRONT SEATBACK SHIELD RH (for Driver Side)


    B190991
  1. Detach the wire harness clamp.

  1. Remove the screw.

  1. Detach the claw and remove the front seatback shield.



23. REMOVE FRONT SEAT CUSHION SHIELD LOWER LH


    B201576
  1. Using a screwdriver, detach the claw and remove the front seat cushion shield lower.

    HINT:
    Tape the screwdriver tip before use.



24. REMOVE FRONT SEAT CUSHION SHIELD LOWER RH

HINT:
Use the same procedure for the LH side and RH side.



25. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (for Driver Side)


    B190989E03
  1. Remove the 2 springs.

  1. Detach the 6 hooks and remove the seatback spring.



    B190990
  1. Disconnect the lumbar support adjuster connector.

  1. Remove the 2 screws and lumbar support adjuster.



    B190994
  1. Detach the 3 claws and remove the bush from the seat frame.



26. REMOVE FRONT SEAT WIRE LH (for Driver Side)


27. REMOVE FRONT SEAT WIRE RH (for Front Passenger Side)


    B190992
  1. Disconnect the 4 connectors.

  1. Detach the wire harness clamp and remove the front seat wire.