Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat)

FRONT SEAT ASSEMBLY (for Manual Seat) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below are for the LH side.



1. INSTALL FRONT SEAT WIRE RH (for Front Passenger Side)


    B190992
  1. Attach the wire harness clamp.

  1. Connect the 4 connectors to install the front seat wire.



2. INSTALL FRONT SEAT WIRE LH (for Driver Side)


3. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (for Driver Side)


    B190994
  1. Attach the 3 claws to install the bush.



    B190990
  1. Install the lumbar support adjuster with the 2 screws.

  1. Connect the lumbar support adjuster connector.



    B190989E03
  1. Attach the 6 hooks to install the seatback springs.

  1. Install the 2 springs.



4. INSTALL FRONT SEAT CUSHION SHIELD LOWER LH


    B201577
  1. Attach the claw to install the front seat cushion shield lower.



5. INSTALL FRONT SEAT CUSHION SHIELD LOWER RH

HINT:
Use the same procedure for the LH side and RH side.



6. INSTALL FRONT SEATBACK SHIELD LH


    B200256
  1. Attach the claw to install the front seatback shield.

  1. Install the screw.



7. INSTALL FRONT SEATBACK SHIELD RH (for Driver Side)


    B190991
  1. Attach the claw to install the front seatback shield.

  1. Install the screw.

  1. Attach the wire harness clamp.



8. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    B191058
  1. Install the reclining adjuster inside cover with the screw.



9. INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedure for the LH side and RH side.



10. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    B190995E04
  1. Using hog ring pliers, install the seatback cover to the seatback pad with 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B166411
  1. Attach the seatback cover bracket to the seatback pad.



    B194820E03
  1. Install the seatback cover wires.

  1. Using hog ring pliers, install 2 new hog rings to the seatback pad.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



11. INSTALL SEATBACK COVER WITH PAD


    B194821E03
  1. Install the seatback cover with pad to the seatback frame.

  1. Lift the seatback cover and, using hog ring pliers, install 4 new hog rings to the seat frame.

  1. Lift the seatback cover, connect the seatback cover bracket to the seat frame, and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    After the seatback trim cover is assembled, make sure that the side airbag strap is not twisted.



12. INSTALL FRONT SEAT HEADREST SUPPORT


    B191062E02
  1. Align the protruding portion of the front seat headrest support with the installation groove of the front seatback frame.

  1. Attach the 4 claws to install the 2 headrest supports.



    B194822E02
  1. Install the seatback cover wires.

  1. Using hog ring pliers, install 2 new hog rings to the seat frame.



    B190983
  1. Attach the hooks.



    B194823E02
  1. Using hog ring pliers, install 3 new hog rings to the seat frame.



13. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


B190997E03
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 10 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



14. INSTALL SEAT CUSHION COVER WITH PAD (for Driver Side)


    B190980
  1. Attach the hooks to install the seat cushion cover with pad.

  1. Bend the 2 seat frame claws downward.



    B190998E03
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion spring with 2 new hog rings.



    B195207
  1. Attach the wire harness clamp.



    B190977
  1. Attach the 8 wire harness clamps.



    B190976
  1. Install the 2 clips.



15. INSTALL SEAT CUSHION COVER WITH PAD (for Front Passenger Side)


    B190981
  1. Attach the hooks to install the seat cushion cover with pad.

  1. Bend the 2 seat frame claws downward.



    B190999E03
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion spring with 2 new hog rings.



    B190979
  1. Attach the 3 wire harness clamps.



    B190978
  1. Install the 2 clips.



16. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)
  1. Install the front seat belt anchor plate.



    B191256E02
  1. Install the front seat inner belt assembly LH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly LH to overlap the protruding part of the front seat adjuster.



    B191249
  1. Connect the connector and attach the 5 clamps.



17. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)
  1. Install the front seat belt anchor plate.



    B191258E02
  1. Install the front seat inner belt assembly RH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly RH to overlap the protruding part of the front seat adjuster.



    B191252
  1. Attach the 3 clamps.



18. INSTALL SEAT POSITION AIRBAG SENSOR
  1. Check that the ignition switch is turned off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B169961E01
  1. Using an 1 mm (0.039 in.) feeler gauge, install the seat position airbag sensor.

    NOTICE:
    1. If the seat position airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace the seat position airbag sensor with a new one.
    2. When installing the seat position airbag sensor, make sure that the SRS wiring does not interfere with other parts and is not pinched between other parts.

    HINT:
    Maintain a clearance between the seat position airbag sensor and the seat rail of between 0.6 mm (0.023 in.) and 2 mm (0.079 in.).



    B194811E02
  1. Using T30 "TORX" socket wrench, tighten the screw to install the seat position airbag sensor.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position airbag sensor and the seat rail is between 0.6 mm (0.023 in.) and 2 mm (0.079 in.).

  1. Connect the connector to the seat position airbag sensor.

  1. Check that there is no looseness in the installation parts of the seat position airbag sensor.

  1. Engage the pin and install a new seat position sensor protector.



19. INSTALL FRONT SEAT CUSHION SHIELD INNER LH


    B191000E01
  1. Attach the wire harness clamp.

  1. Attach the 3 claws in the order shown in the illustration, to install the cushion shield.

  1. Install the screw.



20. INSTALL FRONT POWER SEAT LUMBAR SWITCH (for Driver Side)


    B194037
  1. Install the front power seat lumbar switch with the 2 screws.

  1. Connect the connector.



21. INSTALL FRONT SEAT CUSHION SHIELD LH (for Driver Side)


    B191001E01
  1. Connect the connector and attach the wire harness clamp.

  1. Attach the 3 claws in the order shown in the illustration, to install the front seat cushion shield.

  1. Install the 3 screws.



    B191002E02
  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with 2 new hog rings.



22. INSTALL FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side)


    B166413E01
  1. Attach the 3 claws in the order shown in the illustration, to install the cushion shield.

  1. Install the 2 screws.



    B191043E02
  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with 2 new hog rings.



23. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    B194817
  1. Attach the claw to install the reclining adjuster release handle.



24. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH (for Front Passenger Side)


    B165803
  1. Attach the claw to install the reclining adjuster release handle.



25. INSTALL VERTICAL SEAT ADJUSTER KNOB (for Driver Side)


    B191003
  1. Install the snap ring to the vertical seat adjuster knob.

  1. Install the vertical seat adjuster knob to the front seat.



26. INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)


    B190970
  1. Install the vertical adjusting handle with the 2 screws.



27. INSTALL VERTICAL SEAT ADJUSTER KNOB CAP (for Driver Side)


    B200259
  1. Attach the 2 claws to install the vertical adjuster handle cap.



28. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)


    B194815
  1. Check that the ignition switch is off.

  1. Check that the negative battery (-) terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Attach the claw to install the occupant classification ECU.

  1. Connect the connector to the occupant classification ECU.

    NOTICE:
    1. If the occupant classification ECU has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the occupant classification ECU, make sure that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
    3. When replacing the occupant classification ECU, replace the bolt with a new one.