FRONT SEAT ASSEMBLY (for Fold Down Seat Type) > DISASSEMBLY |
| 1. REMOVE OCCUPANT CLASSIFICATION ECU |
![]() |
Disconnect the connector from the occupant classification ECU.
Detach the claw and remove the occupant classification ECU.
| 2. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH |
![]() |
Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the release handle.
| 3. REMOVE FRONT SEAT CUSHION SHIELD RH |
![]() |
Remove the hog rings and rubber bands of the seatback cover from the seat frame.
![]() |
Remove the 2 screws.
Detach the 3 claws in the order shown in the illustration, and then remove the cushion shield.
| 4. REMOVE INNER FRONT SEAT CUSHION SHIELD RH |
![]() |
Remove the screw.
Detach the 3 claws in the order shown in the illustration, and then remove the cushion shield.
| 5. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH |
![]() |
Detach the 3 clamps.
![]() |
Remove the nut and front seat inner belt RH.
| 6. REMOVE SEAT CUSHION COVER WITH PAD |
![]() |
Using a clip remover, remove the 2 clips.
![]() |
Bend the 2 seat frame claws upward.
Detach the hooks and remove the seat cushion cover with pad.
| 7. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER |
![]() |
Remove the 10 hog rings and seat cushion cover.
| 8. REMOVE RECLINING ADJUSTER RELEASE HANDLE NO. 1 LH |
![]() |
Using a screwdriver, remove the seatback lock handle as shown in the illustration.
| 9. REMOVE RECLINING ADJUSTER RELEASE HANDLE NO. 1 RH |
| 10. REMOVE SEATBACK SHIELD LH |
![]() |
Remove the screw.
Detach the 2 claws and remove the seatback shield.
| 11. REMOVE SEATBACK SHIELD RH |
Remove the screw.
Detach the 2 claws and remove the seatback shield.
![]() |
Disconnect the airbag wire harness from the seatback shield.
| 12. REMOVE FRONT SEATBACK ASSEMBLY |
![]() |
Detach the 2 airbag wire harness clamps from the seat frame.
![]() |
Remove the 4 bolts and seatback assembly.
| 13. REMOVE FRONT SEATBACK BOARD |
![]() |
Detach the 2 clips and 2 hooks, and then remove the seatback board.
| 14. REMOVE FRONT SEATBACK LOCK SUB-ASSEMBLY LH |
![]() |
Remove the 2 bolts and seatback lock.
| 15. REMOVE FRONT SEATBACK LOCK SUB-ASSEMBLY RH |
| 16. REMOVE FRONT SEATBACK LOCK HANDLE ROD |
| 17. REMOVE FRONT SEAT HINGE COVER LH |
![]() |
Detach the 2 claws and remove the seat hinge cover.
| 18. REMOVE FRONT SEAT HINGE COVER RH |
| 19. REMOVE SEATBACK COVER WITH PAD |
![]() |
Remove the nut and detach the seatback cover bracket from the seatback spring.
![]() |
Remove the 11 hog rings.
![]() |
Remove the 4 hog rings.
![]() |
Detach the 4 claws and remove the 2 headrest supports.
Remove the seatback cover with pad.
| 20. REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Remove the 2 hog rings and seatback cover wires.
![]() |
Detach the seatback cover bracket from the seatback pad.
![]() |
Remove the 2 hog rings and seatback cover from the seatback pad.
| 21. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the screw and reclining adjuster inside cover.
| 22. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
| 23. REMOVE FRONT SEATBACK SHIELD LH |
![]() |
Remove the screw.
Detach the claw and remove the reclining adjuster inside cover.
| 24. REMOVE FRONT SEATBACK SHIELD RH |
| 25. REMOVE FRONT SEAT CUSHION SHIELD LOWER LH |
![]() |
Using a screwdriver, detach the claw and remove the seat cushion shield.
| 26. REMOVE FRONT SEAT CUSHION SHIELD LOWER RH |
| 27. REMOVE FRONT SEAT WIRE RH |
![]() |
Disconnect the 4 connectors.
Detach the wire harness clamp and remove the front seat wire.