Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Fold Down Seat Type)

FRONT SEAT ASSEMBLY (for Fold Down Seat Type) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL FRONT SEAT WIRE RH


    B190992
  1. Attach the wire harness clamp.

  1. Connect the 4 connectors to install the front seat wire.



2. INSTALL FRONT SEAT CUSHION SHIELD LOWER LH


    B201577
  1. Attach the claw to install the cushion shield.



3. INSTALL FRONT SEAT CUSHION SHIELD LOWER RH

HINT:
Use the same procedure for the LH side and RH side.



4. INSTALL FRONT SEATBACK SHIELD LH


    B191059
  1. Attach the claw to install the reclining adjuster inside cover.

  1. Install the screw.



5. INSTALL FRONT SEATBACK SHIELD RH

HINT:
Use the same procedure for the LH side and RH side.



6. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    B191058
  1. Install the reclining adjuster inside cover with the screw.



7. INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedure for the LH side and RH side.



8. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    B191060E02
  1. Using hog ring pliers, install the seatback cover to the seatback pad with 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B166411
  1. Attach the seatback cover bracket to the seatback pad.



    B191061E02
  1. Install the seatback cover wires.

  1. Using hog ring pliers, install 2 new hog rings to the seatback pad.



9. INSTALL SEATBACK COVER WITH PAD


    B191062E02
  1. Install the seatback cover with pad to the seatback spring.

  1. Align the protruding portion of the front seat headrest support with the installation groove of the front seatback frame.

  1. Attach the 4 claws to install the 2 headrest supports.



    B191063E02
  1. Using hog ring pliers, install 4 new hog rings to the seatback spring.



    B191064E02
  1. Using hog ring pliers, install 11 new hog rings to the seatback spring.



    B191052
  1. Attach the seatback cover bracket to the seatback spring and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    After the seatback trim cover is assembled, make sure that the side airbag strap is not twisted.



10. INSTALL FRONT SEAT HINGE COVER RH


    B165551
  1. Attach the 2 claws to install the hinge cover.



11. INSTALL FRONT SEAT HINGE COVER LH

HINT:
Use the same procedure for the LH side and RH side.



12. INSTALL FRONT SEATBACK LOCK SUB-ASSEMBLY RH


    B191051
  1. Install the seatback lock with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



13. INSTALL FRONT SEATBACK LOCK HANDLE ROD


    B165799
  1. Install the seatback lock handle rod.

    NOTICE:
    Install the rod as shown in the illustration.



14. INSTALL FRONT SEATBACK LOCK SUB-ASSEMBLY LH


    B191050
  1. Install the seatback lock with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    NOTICE:
    Connect the rod and seatback lock before installing the bolts.



15. INSTALL FRONT SEATBACK BOARD


    B191065
  1. Attach the 2 hooks to install the seatback board, and then attach the 2 clips.



16. INSTALL FRONT SEATBACK ASSEMBLY


    B191048
  1. Install the seatback with the 4 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    B191047
  1. Attach the 2 airbag wire harness clamps to the seat frame.



17. INSTALL SEATBACK SHIELD LH


    B165546
  1. Connect the airbag wire harness to the seatback shield.



    B191046
  1. Attach the 2 claws to install the seatback shield.

  1. Install the screw.



18. INSTALL SEATBACK SHIELD RH
  1. Attach the 2 claws to install the seatback shield.

  1. Install the screw.



19. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO. 1 LH


    B165808
  1. Install the reclining adjuster release handle.



20. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO. 1 RH

HINT:
Use the same procedure for the LH side and RH side.



21. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    B191066E02
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 10 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



22. INSTALL SEAT CUSHION COVER WITH PAD


    B191044
  1. Attach the hooks to install the seat cushion cover with pad.

  1. Bend the 2 seat frame claws downward.



    B201578
  1. Install the 2 clips.



23. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH


    B191258E02
  1. Install the front seat inner belt assembly RH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt to overlap the protruding part of the front seat adjuster.



    B191252
  1. Attach the 3 clamps.



24. INSTALL INNER FRONT SEAT CUSHION SHIELD RH


    B166414E01
  1. Attach the 3 claws in the order shown in the illustration, to install the cushion shield.

  1. Install the screw.



25. INSTALL FRONT SEAT CUSHION SHIELD RH


    B166413E01
  1. Attach the 3 claws in the order shown in the illustration, to install the cushion shield.

  1. Install the 2 screws.



    B191043E02
  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with 2 new hog rings.



26. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH


    B165803
  1. Attach the claw to install the reclining adjuster release handle.



27. INSTALL OCCUPANT CLASSIFICATION ECU


    B194815
  1. Check that the ignition switch is off.

  1. Check that the negative battery (-) terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Attach the claw to install the occupant classification ECU.

  1. Connect the connector to the occupant classification ECU.

    NOTICE:
    1. If the occupant classification ECU has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the occupant classification ECU, make sure that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
    3. When replacing the occupant classification ECU, replace the bolt with a new one.