Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Power Seat)

FRONT SEAT ASSEMBLY (for Power Seat) > DISASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below are for the LH side.



1. REMOVE OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)


    B194816
  1. Disconnect the 2 connectors from the occupant classification ECU.

  1. Detach the claw and remove the occupant classification ECU.



2. REMOVE SEAT POSITION AIRBAG SENSOR (for Driver Side)


    B194812
  1. Disconnect the connector from the seat position airbag sensor.

  1. Using "TORX" socket wrench T30, remove the "TORX" screw and the seat position airbag sensor.

  1. Remove the seat slide position sensor protector from the seat position airbag sensor.



3. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    B201567E02
  1. Apply protective tape around the cushion shield.

  1. Using a screwdriver, detach the 2 claws and remove the knob.

    HINT:
    Tape the screwdriver tip before use.



4. REMOVE RECLINING POWER SEAT SWITCH KNOB


    B201568E02
  1. Using a screwdriver, detach the 2 claws and remove the knob.

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE FRONT SEAT CUSHION SHIELD LH


    B191013
  1. Remove the 2 hog rings and rubber bands of the seatback cover from the seat frame.

  1. Remove the 2 screws.



    B166945
  1. Remove the 3 screws.

  1. Detach the 2 claws and remove the cushion shield.

  1. Disconnect the connectors.



6. REMOVE FRONT POWER SEAT LUMBAR SWITCH


    B201589
  1. Disconnect the connector.

  1. Remove the 2 screws and front power seat lumbar switch.



7. REMOVE LEG SUPPORT ADJUSTMENT SWITCH (w/ Leg Support Adjustment Switch)


    B191014
  1. Detach the 2 wire harness clamps.

  1. Remove the 2 screws and leg support adjustment switch.

  1. Disconnect the connector.



8. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH


    B191250
  1. Disconnect the connector and detach the 5 clamps.



    B191259
  1. Remove the nut and front seat inner belt LH.



9. REMOVE FRONT SEAT CUSHION SHIELD INNER LH


    B191015
  1. Remove the screw.

  1. Detach the 2 claws and clip, and then remove the cushion shield.



10. REMOVE FRONT POWER SEAT SWITCH LH


    B166949
  1. Disconnect the connectors.

  1. Remove the 3 screws and switch.



11. REMOVE SEAT CUSHION COVER WITH PAD (w/ Leg Support Adjustment Switch)


    B167097
  1. Using a clip remover, remove the 2 clips.



    B191016E01
  1. Disconnect the connector and detach the 2 wire harness clamps.



    B191017
  1. Disconnect the connector and detach the 2 wire harness clamps.



    B191018
  1. Remove the 4 hog rings and detach the hooks.



    B167096
  1. Remove the seat cushion cover wire.

  1. Remove the seat cushion cover with pad from the seat frame.



12. REMOVE SEAT CUSHION COVER WITH PAD (w/o Leg Support Adjustment Switch)


    B167097
  1. Using a clip remover, remove the 2 clips.



    B194825E01
  1. Disconnect the connector and detach the 2 wire harness clamps.



    B194826
  1. Disconnect the connector and detach the 2 wire harness clamps.



    B191019
  1. Remove the 2 hog rings.

  1. Bend the 2 seat frame claws upward.

  1. Detach the hooks and remove the seat cushion cover with pad.



13. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (w/ Leg Support Adjustment Switch)


  1. Remove the 15 hog rings and front seat cushion cover.


    B191020



14. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (w/o Leg Support Adjustment Switch)


    B191021
  1. Remove the 10 hog rings and front seat cushion cover.



15. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)


    B194831
  1. Cut off the 30 tack pins which fasten the seat heater to the seat cushion cover, and then remove the seat cushion heater from the seat cushion cover.



16. REMOVE FRONT SEAT HEADREST SUPPORT


    B191022
  1. Remove the 3 hog rings.



    B191023
  1. Detach the hooks.



    B191024
  1. Remove the 2 hog rings and seatback cover wires.



    B191055
  1. Detach the 4 claws and remove the 2 headrest supports.



17. REMOVE SEATBACK COVER WITH PAD


    B190986
  1. Lift the seatback cover and remove the nut and seatback cover bracket from the seat frame.

  1. Lift the seatback cover and remove the 4 hog rings and seatback cover with pad.



18. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    B195620
  1. Remove the 2 hog rings and seatback cover wires.



    B165535
  1. Detach the seatback cover bracket from the seatback pad.



    B191026
  1. Remove the 2 hog rings and seatback cover from the seatback pad.



19. REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)


    B194830
  1. Cut off the 9 tack pins which fasten the seatback heater to the seatback cover, and then remove the seatback heater from the seatback cover.



20. REMOVE RECLINING ADJUSTER INSIDE COVER LH


    B201569
  1. Remove the screw.

  1. Detach the claw and remove the reclining adjuster inside cover.



21. REMOVE RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedure for the LH side and RH side.



22. REMOVE FRONT SEATBACK SHIELD LH


    B201570
  1. Remove the 2 screws.

  1. Detach the claw and remove the front seatback shield.



23. REMOVE FRONT SEATBACK SHIELD RH


    B191027
  1. Detach the wire harness clamp.

  1. Remove the 2 screws.

  1. Detach the claw and remove the front seatback shield.



24. REMOVE FRONT SEAT CUSHION SHIELD SUB-ASSEMBLY LH NO. 2


    B201571
  1. Remove the screw.

  1. Detach the hook and remove the cushion shield.



25. REMOVE FRONT SEAT CUSHION SHIELD SUB-ASSEMBLY LH NO. 1

HINT:
Use the same procedure for the LH side and RH side.



26. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Climate Control Seat System)


    B232376
  1. Disconnect the connector and detach the 2 clamps.



    B194042E01
  1. Remove the 4 springs.

  1. Detach the 4 hooks and remove the seatback spring.



    B200258
  1. Disconnect the connector.

  1. Remove the 2 screws and lumbar support adjuster.



    B167110
  1. Detach the 3 claws and remove the bush from the seat frame.



27. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/o Climate Control Seat System)


    B191028E01
  1. Remove the 2 springs.

  1. Detach the 6 hooks and remove the seatback spring.



    B200258
  1. Disconnect the connector.

  1. Remove the 2 screws and lumbar support adjuster.



    B167110
  1. Detach the 3 claws and remove the bush from the seat frame.



28. REMOVE SEATBACK CLIMATE CONTROL COVER LH NO. 1 (w/ Climate Control Seat System)


    B232101
  1. Using a T30 "TORX" socket wrench, remove the 4 "TORX" screws and then remove the seatback climate control cover LH No. 1.



29. REMOVE SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)


    B194060
  1. Detach the clamp.

  1. Using a T30 "TORX" socket wrench, remove the 2 "TORX" screws and then remove the seatback climate control blower LH and seatback climate control cover LH No. 3.



30. REMOVE SEATBACK CLIMATE CONTROL COVER LH NO. 2 (w/ Climate Control Seat System)


    B194062
  1. Detach the 6 clamps and remove the seatback climate control cover LH No. 2.



31. REMOVE SEAT CUSHION CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System)


    B201572E01
  1. Detach the 2 clamps (A) in the direction indicated by the arrow (1).

  1. Detach the 2 clamps (B) in the direction indicated by the arrow (2).

  1. Detach the 2 claws, and remove the seat cushion climate control duct LH.



32. REMOVE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY (w/ Climate Control Seat System)


    B120540E02
  1. Disconnect the connector.

  1. Using a T30 "TORX" socket wrench, remove the "TORX" screw.

  1. Bend the bracket open slightly.

  1. Detach the 2 claws and remove the seat cushion climate control blower by pushing it rearward.



33. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)


    B191029
  1. Disconnect the seat heater control connector and detach the clamp.

  1. Detach the clamp and remove the seat heater control.



34. REMOVE FRONT SEAT WIRE LH (for Driver Side)


    B191030
  1. Disconnect the 3 connectors.

  1. Detach the 6 wire harness clamps.



35. REMOVE FRONT SEAT WIRE RH (for Front Passenger Side)


    B191031
  1. Disconnect the 5 connectors.

  1. Detach the 7 wire harness clamps.



36. REMOVE FRONT POWER SEAT MOTOR ASSEMBLY (for Driver Side)


    B232086
  1. Put matchmarks on the seat track rail and sliding unit of the seat frame.



    B108592
  1. Connect the positive (+) battery terminal to terminal 1 of the power seat motor and the negative (-) battery terminal to terminal 2 and slide the seat to the foremost position.



    B232087
  1. Loosen the 2 nuts.



    B108592
  1. Connect the positive (+) battery terminal to terminal 2 of the power seat motor and the negative (-) battery terminal to terminal 1 and slide the seat to the rearmost position.



    B231462
  1. Using a 4 mm socket hexagon wrench, remove the 4 bolts.

  1. Remove the 2 nuts and front power seat motor assembly (slide motor).

    NOTICE:
    Do not apply excessive force to the slide cable (do not bend the slide cable 60° or more).



37. REMOVE FRONT POWER SEAT MOTOR ASSEMBLY (for Front Passenger Side)


    B232088
  1. Put matchmarks on the seat track rail and sliding unit of the seat frame.



    B108592
  1. Connect the positive (+) battery terminal to terminal 1 of the power seat motor and the negative (-) battery terminal to terminal 2 and slide the seat to the foremost position.



    B232089
  1. Loosen the 2 nuts.



    B108592
  1. Connect the positive (+) battery terminal to terminal 2 of the power seat motor and the negative (-) battery terminal to terminal 1 and slide the seat to the rearmost position.



    B232090
  1. Using a 4 mm socket hexagon wrench, remove the 4 bolts.

  1. Remove the 2 nuts and front power seat motor assembly (slide motor).

    NOTICE:
    Do not apply excessive force to the slide cable (do not bend the slide cable 60° or more).