Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Power Seat)

FRONT SEAT ASSEMBLY (for Power Seat) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below are for the LH side.



1. INSTALL FRONT POWER SEAT MOTOR ASSEMBLY (for Driver Side)


    B231462E01
  1. Install the front power seat motor assembly (slide motor) to the slide screws.

    NOTICE:
    1. Make sure that the slide rail is locked in the rearmost position.
    2. If the serrations on the slide screw and front power seat motor assembly with slide cable do not align, grip the slide screw with needlenose pliers and install the front power seat motor assembly with slide cable while slightly moving the slide screw. In these cases, do not turn the slide screw 90° or more.
    3. Do not apply excessive force to the slide cable (do not bend the slide cable 60° or more).

  1. Clean the slide screws with non-residue solvent and apply adhesive to their threads.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using a 4 mm socket hexagon wrench, install the new 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Using a 4 mm socket hexagon wrench, install the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    B232087
  1. Install the 2 nuts.

    Torque:
    3.4 N*m{ 35 kgf*cm , 30 in.*lbf }



    B108592
  1. Connect the positive (+) battery terminal to terminal 1 of the power seat motor and the negative (-) battery terminal to terminal 2 and slide the seat and align the matchmarks.



    B232086
  1. Check that the matchmarks are aligned on both sides. If the matchmarks are not aligned, check the installation condition of the power seat motor assembly, and remove and reinstall the power seat motor assembly if necessary.



2. INSTALL FRONT POWER SEAT MOTOR ASSEMBLY (for Front Passenger Side)


    B232090E01
  1. Install the front power seat motor assembly (slide motor) to the slide screws.

    NOTICE:
    1. Make sure that the slide rail is locked in the rearmost position.
    2. If the serrations on the slide screw and front power seat motor assembly with slide cable do not align, grip the slide screw with needlenose pliers and install the front power seat motor assembly with slide cable while slightly moving the slide screw. In these cases, do not turn the slide screw 90° or more.
    3. Do not apply excessive force to the slide cable (do not bend the slide cable 60° or more).

  1. Clean the slide screws with non-residue solvent and apply adhesive to their threads.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using a 4 mm socket hexagon wrench, install the new 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Using a 4 mm socket hexagon wrench, install the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    B232089
  1. Install the 2 nuts.

    Torque:
    3.4 N*m{ 35 kgf*cm , 30 in.*lbf }



    B108592
  1. Connect the positive (+) battery terminal to terminal 2 of the power seat motor and the negative (-) battery terminal to terminal 1, and then slide the seat and align the matchmarks.



    B232088
  1. Check that the matchmarks are aligned on both sides. If the matchmarks are not aligned, check the installation condition of the power seat motor assembly, and remove and reinstall the power seat motor assembly if necessary.



3. INSTALL FRONT SEAT WIRE LH (for Driver Side)


    B191030
  1. Connect the 3 connectors and attach the 6 wire harness clamps.



4. INSTALL FRONT SEAT WIRE RH (for Front Passenger Side)


    B191031
  1. Connect the 5 connectors and attach the 7 wire harness clamps.



5. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)


    B191029
  1. Attach the clamp to install the seat heater control.

  1. Attach the clamp to connect the connector.



6. INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY (w/ Climate Control Seat System)


    B146608E04
  1. Attach the 2 claws to install the seat cushion climate control blower by pushing it forward.

  1. Bend the bracket closed.

  1. Using a T30 "TORX" socket wrench, install the "TORX" screw.

    Torque:
    2.6 N*m{ 27 kgf*cm , 23 in.*lbf }

  1. Connect the connector.



7. INSTALL SEAT CUSHION CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System)


    B201573E01
  1. Attach the 2 claws to install the seat cushion climate control duct.

  1. Attach the 2 clamps (B).

  1. Attach the 2 clamps (A).



8. INSTALL SEATBACK CLIMATE CONTROL COVER LH NO. 2 (w/ Climate Control Seat System)


    B194062
  1. Attach the 6 clamps to install the seatback climate control cover LH No. 2.



9. INSTALL SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)


B194060
  1. Install the seatback climate control cover LH No. 3.

  1. Using a T30 "TORX" socket wrench, install the seatback climate control blower with the 2 "TORX" screws.

  1. Attach the connector.



10. INSTALL SEATBACK CLIMATE CONTROL COVER LH NO. 1 (w/ Climate Control Seat System)


    B232101
  1. Using a T30 "TORX" socket wrench, install the seatback climate control cover LH No. 1 with the 4 "TORX" screws.



11. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Climate Control Seat System)


    B167110
  1. Attach the 3 claws to install the bush.



    B200258
  1. Install the lumbar support adjuster with the 2 screws.

  1. Connect the connector.



    B194042E01
  1. Attach the 4 hooks to install the seatback spring.

  1. Install the 4 springs.



    B232376
  1. Attach the 2 clamps and connect the connector.



12. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/o Climate Control Seat System)


    B167110
  1. Attach the 3 claws to install the bush.



    B200258
  1. Install the lumbar support adjuster with the 2 screws.

  1. Connect the lumbar support adjuster connector.



    B191028E01
  1. Attach the 6 hooks to install the seatback spring.



13. INSTALL FRONT SEAT CUSHION SHIELD SUB-ASSEMBLY LH NO. 2


    B201571
  1. Attach the hook to install the cushion shield.

  1. Install the screw.



14. INSTALL FRONT SEAT CUSHION SHIELD SUB-ASSEMBLY LH NO. 1

HINT:
Use the same procedure for the LH side and RH side.



15. INSTALL FRONT SEATBACK SHIELD LH


    B201570
  1. Attach the claw to install the seatback shield.

  1. Install the 2 screws.



16. INSTALL FRONT SEATBACK SHIELD RH


    B191027
  1. Attach the claw to install the seatback shield.

  1. Install the 2 screws.

  1. Attach the wire harness clamp.



17. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    B201569
  1. Attach the claw to install the reclining adjuster inside cover.

  1. Install the screw.



18. INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedure for the LH side and RH side.



19. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)


    B194830
  1. Set the seatback heater with the name stamp side facing the seatback cover.

  1. Install the seatback heater with 9 new tack pins.

    NOTICE:
    Do not bend or fold the seatback heater assembly.



20. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    B191032E02
  1. Using hog ring pliers, install the seatback cover to the seatback pad with 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B166411
  1. Attach the seatback cover bracket to the seatback pad.



    B194827E02
  1. Install the seatback cover wires.

  1. Using hog ring pliers, install 2 new hog rings to the seatback pad.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



21. INSTALL SEATBACK COVER WITH PAD


    B194821E03
  1. Install the seatback cover with pad to the seatback frame.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. Lift the seatback cover and, using hog ring pliers, install 4 new hog rings to the seat frame.

  1. Lift the seatback cover, connect the seatback cover bracket to the seat frame, and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    After the seatback trim cover is assembled, make sure that the side airbag strap is not twisted.



    B194828E02
  1. Install the seatback cover wires.

  1. Using hog ring pliers, install 2 new hog rings to the seat frame.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B191023
  1. Attach the hooks.



    B194829E02
  1. Using hog ring pliers, install 3 new hog rings to the seat frame.



22. INSTALL FRONT SEAT HEADREST SUPPORT


    B191062E04
  1. Align the protruding portion of the front seat headrest supports with the installation grooves of the front seatback frame.

  1. Attach the 4 claws to install the 2 headrest supports.



23. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)


    B194831
  1. Set the seat cushion heater with the name stamp side facing the seat cushion cover.

  1. Install the seat cushion heater with 30 new tack pins.

    NOTICE:
    Do not bend or fold the seat cushion heater assembly.



24. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/ Leg Support Adjustment Switch)


  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 15 new hog rings.


    B191035E03

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



25. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/o Leg Support Adjustment Switch)


    B191036E02
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 10 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



26. INSTALL SEAT CUSHION COVER WITH PAD (w/ Leg Support Adjustment Switch)


    B167190
  1. Install the seat cushion cover with pad to the seat frame.

  1. Install the seat cushion cover wire.



    B195224E02
  1. Using hog ring pliers, install 4 new hog rings and attach the hooks.

    HINT:
    When installing the leg support hog rings, press the seat cushion cover with pad against the seat frame.



    B191017
  1. Connect the connector and attach the 2 wire harness clamps.



    B191016E01
  1. Connect the connector and attach the 2 wire harness clamps.



    B167097
  1. Install the 2 clips.



27. INSTALL SEAT CUSHION COVER WITH PAD (w/o Leg Support Adjustment Switch)


    B195225E02
  1. Attach the hooks to install the seat cushion cover with pad.

  1. Using hog ring pliers, install 2 new hog rings.

  1. Bend the 2 seat frame claws downward.



    B194826
  1. Connect the connector and attach the 2 wire harness clamps.



    B194825
  1. Connect the connector and attach the 2 wire harness clamps.



    B167097
  1. Install the 2 clips.



28. INSTALL FRONT POWER SEAT SWITCH LH


    B166949
  1. Install the switch with the 3 screws.

  1. Connect the connectors.



29. INSTALL FRONT SEAT CUSHION SHIELD INNER LH


B191015
  1. Attach the 2 claws and clip to install the cushion shield.

  1. Install the screw.



30. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


    B191260E03
  1. Install the front seat inner belt assembly LH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt to overlap the protruding part of the front seat adjuster.



    B191250
  1. Connect the connector and attach the 5 clamps.



31. INSTALL LEG SUPPORT ADJUSTMENT SWITCH (w/ Leg Support Adjustment Switch)


    B191014
  1. Connect the connector.

  1. Install the leg support adjustment switch with the 2 screws.

  1. Attach the 2 wire harness clamps.



32. INSTALL FRONT POWER SEAT LUMBAR SWITCH


    B201589
  1. Install the front power seat lumbar switch with the 2 screws.

  1. Connect the connector.



33. INSTALL FRONT SEAT CUSHION SHIELD LH


    B166945
  1. Connect the switch connectors.

  1. Attach the 2 claws to install the cushion shield.

  1. Install the 3 screws.



    B195226E02
  1. Install the 2 screws.

  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with 2 new hog rings.



34. INSTALL RECLINING POWER SEAT SWITCH KNOB


B201574
  1. Attach the 2 claws to install the knob.



35. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


B201575
  1. Attach the 2 claws to install the knob.



36. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)
  1. Check that the ignition switch is turned off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B169961E01
  1. Using an 1 mm (0.039 in.) feeler gauge, install the seat position airbag sensor.

    NOTICE:
    1. If the seat position airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace the seat position airbag sensor with a new one.
    2. When installing the seat position airbag sensor, make sure that the SRS wiring does not interfere with other parts and is not pinched between other parts.

    HINT:
    Maintain a clearance between the seat position airbag sensor and the seat rail of between 0.6 mm (0.023 in.) and 2 mm (0.079 in.).



    B194812E01
  1. Using "TORX" socket wrench, tighten the "TORX" screw to install the seat position airbag sensor.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position airbag sensor and the seat rail is between 0.6 mm (0.023 in.) and 2 mm (0.079 in.).

  1. Connect the connector to the seat position airbag sensor.

  1. Check that there is no looseness in the installation parts of the seat position airbag sensor.

  1. Engage the pin and install a new seat position sensor protector.



37. INSTALL OCCUPANT CLASSIFICATION ECU


    B194816
  1. Check that the ignition switch is off.

  1. Check that the negative battery (-) terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Attach the claw to install the occupant classification ECU.

  1. Connect the 2 connectors to the occupant classification ECU.

    NOTICE:
    1. If the occupant classification ECU has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the occupant classification ECU, make sure that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
    3. When replacing the occupant classification ECU, replace the bolt with a new one.