Home › Vehicle Interior › SEAT › SEAT HEATER SWITCH (for Front Seat)

SEAT HEATER SWITCH (for Front Seat) > INSPECTION

for Preparation Click here



1. INSPECT SEAT HEATER SWITCH LH


B165795E05
  1. Check the resistance.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      3 (SW) - 7 (RV)
      Switch off
      2.7 to 4.1 kΩ
      Switch on (Min.)
      Switch on (Max.)
      0.28 to 0.42 kΩ

      HINT:
      As the dial is being turned, the resistance changes gradually.

      If the result is not as specified, replace the switch.

  1. Check the illumination operation.

    1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

      OK:
      Measurement Condition
      Switch Condition
      Specified Condition
      Battery positive (+) → 8 (ILL+)
      Battery negative (-) → 2 (ILL-)
      Always
      Pointer and level
      illuminates

      If the result is not as specified, replace the switch.

  1. Check the indicator operation.

    1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

      OK:
      Measurement Condition
      Switch Condition
      Specified Condition
      Battery positive (+) → 9 (IG)
      Battery negative (-) → 4 (E)
      Switch on
      Indicator
      illuminates

      If the result is not as specified, replace the switch.



2. INSPECT SEAT HEATER SWITCH RH


B165796E05
  1. Check the resistance.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      2 (SW) - 5 (RV)
      Switch off
      2.7 to 4.1 kΩ
      Switch on (Min.)
      Switch on (Max.)
      0.28 to 0.42 kΩ

      HINT:
      As the dial is being turned, the resistance changes gradually.

      If the result is not as specified, replace the switch.

  1. Check the illumination operation.

    1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

      OK:
      Measurement Condition
      Switch Condition
      Specified Condition
      Battery positive (+) → 6 (ILL+)
      Battery negative (-) → 1 (ILL-)
      Always
      Pointer and level
      illuminates

      If the result is not as specified, replace the switch.

  1. Check the indicator operation.

    1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

      OK:
      Measurement Condition
      Switch Condition
      Specified Condition
      Battery positive (+) → 7 (IG)
      Battery negative (-) → 3 (E)
      Switch on
      Indicator
      illuminates

      If the result is not as specified, replace the switch.



3. INSPECT SEAT HEATER AND CLIMATE SWITCH LH (w/ Climate Control Seat System)



B194049E03

  1. Check the resistance.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for Heater):
      Tester Connection
      Switch Condition
      Specified Condition
      2 (SW) - 6 (RV)
      Switch off
      2.2 to 4.0 kΩ
      Switch on (Min.)
      Switch on (Max.)
      0.3 to 0.5 kΩ

      Standard Resistance (for Blower):
      Tester Connection
      Switch Condition
      Specified Condition
      5 (BLLH) - 4 (SW-)
      Switch off
      1.54 to 2.86 kΩ
      Switch on (Min.)
      Switch on (Max.)
      Below 0.1 kΩ

      HINT:
      As the dial is being turned, the resistance changes gradually.

      If the result is not as specified, replace the switch.

  1. Check the illumination operation.

    1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

      OK:
      Measurement Condition
      Switch Condition
      Specified Condition
      Battery positive (+) → 7 (ILL+)
      Battery negative (-) → 1 (ILL-)
      Always
      Pointer and level
      illuminates

      If the result is not as specified, replace the switch.

  1. Check the indicator operation.

    1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

      OK:
      Measurement Condition
      Switch Condition
      Specified Condition
      Battery positive (+) → 8 (IG)
      Battery negative (-) → 3 (E)
      Switch on
      Indicator
      illuminates

      If the result is not as specified, replace the switch.



4. INSPECT SEAT HEATER AND CLIMATE SWITCH RH (w/ Climate Control Seat System)



B194050E01

  1. Check the resistance.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for Heater):
      Tester Connection
      Switch Condition
      Specified Condition
      4 (SW) - 10 (RV)
      Switch off
      2.2 to 4.0 kΩ
      Switch on (Min.)
      Switch on (Max.)
      0.3 to 0.5 kΩ

      Standard Resistance (for Blower):
      Tester Connection
      Switch Condition
      Specified Condition
      7 (BLRH) - 6 (SVSG)
      Switch off
      1.54 to 2.86 kΩ
      Switch on (Min.)
      Switch on (Max.)
      Below 0.1 kΩ

      HINT:
      As the dial is being turned, the resistance changes gradually.

      If the result is not as specified, replace the switch.

  1. Check the illumination operation.

    1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

      OK:
      Measurement Condition
      Switch Condition
      Specified Condition
      Battery positive (+) → 11 (ILL+)
      Battery negative (-) → 5 (ILL-)
      Always
      Pointer and level
      illuminates

      If the result is not as specified, replace the switch.

  1. Check the indicator operation.

    1. Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

      OK:
      Measurement Condition
      Switch Condition
      Specified Condition
      Battery positive (+) → 12 (IG)
      Battery negative (-) → 3 (E)
      Switch on
      Indicator
      illuminates

      If the result is not as specified, replace the switch.