REAR SEATBACK HEATER > REMOVAL |
| 1. REMOVE REAR NO. 1 SEAT ASSEMBLY RH |
Remove the rear No. 1 seat assembly (Click here).
| 2. REMOVE RECLINING ADJUSTER KNOB CAP RH |
![]() |
Using a screwdriver, detach the 3 claws and remove the reclining adjuster knob cap.
| 3. REMOVE REAR SEAT RECLINING RELEASE LEVER |
![]() |
Remove the 3 screws and rear seat reclining release lever.
| 4. REMOVE REAR SEAT CUSHION HINGE COVER NO. 3 |
![]() |
Remove the screw.
Detach the 2 claws and remove the rear seat cushion hinge cover.
| 5. REMOVE REAR SEAT CUSHION HINGE COVER NO. 2 |
![]() |
Remove the screw.
Detach the 2 claws and remove the rear seat cushion hinge cover.
| 6. REMOVE REAR NO. 1 SEAT CUSHION ASSEMBLY RH |
![]() |
Disconnect the connector and detach the 3 clamps.
![]() |
Cut the cable tie.
Disconnect the cable from the seat cushion spring.
![]() |
Cut the cable tie to remove the cable from the seat cushion spring.
Detach the cable clamp and remove the cable from the seat cushion spring.
![]() |
Detach the 2 clamps to remove the cable from the seat cushion spring.
![]() |
Remove the 2 bolts.
Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts and 2 bushes. Then remove the rear No. 1 seat cushion.
| 7. REMOVE NO. 1 SEAT CUSHION COVER RH |
![]() |
Detach the cable clamp and disconnect the cable from the No. 1 seat cushion cover.
Remove the 2 screws.
Detach the claw and remove the No. 1 seat cushion cover.
| 8. REMOVE REAR SEAT HEADREST ASSEMBLY |
| 9. REMOVE REAR SEAT BACK BOARD SUB-ASSEMBLY RH |
![]() |
Detach the 7 clips and remove the rear seatback board.
| 10. REMOVE REAR SEAT CUSHION HINGE COVER NO. 1 |
![]() |
Remove the screw.
Detach the 4 claws and clip and remove the rear seat cushion hinge cover.
| 11. REMOVE REAR SEAT CUSHION HINGE COVER RH |
![]() |
Remove the 2 screws.
Detach the 3 claws and remove the rear seat cushion hinge cover.
| 12. REMOVE REAR SEAT CUSHION UNDER COVER RH |
![]() |
Remove the 3 screws and rear seat cushion under cover.
| 13. REMOVE REAR SEATBACK LOCK STRIKER COVER |
![]() |
Using a screwdriver, detach the claw and guide and remove the rear seatback lock striker cover.
| 14. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH |
![]() |
Remove the 2 screws.
Disconnect the cable and remove the rear seat lock control lever.
| 15. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY |
![]() |
Detach the 4 claws and remove the 2 rear seat headrest supports.
| 16. REMOVE NO. 1 SEATBACK COVER SUB-ASSEMBLY RH |
![]() |
Remove the 2 hog rings.
Remove the hooks and No. 1 seatback cover.
| 17. REMOVE SEATBACK COVER WITH PAD |
![]() |
Detach the wire harness clamp and disconnect the connector.
![]() |
Remove the 2 hog rings.
![]() |
Detach the hooks and remove the seatback cover with pad.
| 18. REMOVE SEPARATE TYPE REAR SEATBACK COVER |
![]() |
Remove the 8 hog rings and separate type rear seatback cover from the seatback pad.
| 19. REMOVE SEATBACK HEATER ASSEMBLY |
![]() |
Cut off the tack pins which fasten the seat heater to the seatback cover, and then remove the seatback heater from the seatback cover.