Home › Vehicle Interior › SEAT › FRONT SEAT CUSHION HEATER

FRONT SEAT CUSHION HEATER > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below are for the LH side.



1. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH


    B194831
  1. Set the seat cushion heater with the name stamp side facing the seat cushion cover.

  1. Install the seat cushion heater with 30 new tack pins.

    NOTICE:
    Do not bend or fold the seat cushion heater assembly.



2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/ Leg Support Adjustment Switch)


  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 15 new hog rings.


    B191035E03

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



3. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/o Leg Support Adjustment Switch)


    B191036E02
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 10 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



4. INSTALL SEAT CUSHION COVER WITH PAD (w/ Leg Support Adjustment Switch)


    B167190
  1. Install the seat cushion cover with pad to the seat frame.

  1. Install the seat cushion cover wire.



    B195224E02
  1. Using hog ring pliers, install 4 new hog rings and attach the hooks.

    HINT:
    When installing the leg support hog rings, press the seat cushion cover with pad against the seat frame.



    B191017
  1. Connect the connector and attach the 2 wire harness clamps.



    B191016E01
  1. Connect the connector and attach the 2 wire harness clamps.



    B167097
  1. Install the 2 clips.



5. INSTALL SEAT CUSHION COVER WITH PAD (w/o Leg Support Adjustment Switch)


    B195225E02
  1. Attach the hooks to install the seat cushion cover with pad.

  1. Using hog ring pliers, install 2 new hog rings.

  1. Bend the 2 seat frame claws downward.



    B194826
  1. Connect the connector and attach the 2 wire harness clamps.



    B194825
  1. Connect the connector and attach the 2 wire harness clamps.



    B167097
  1. Install the 2 clips.



6. INSTALL FRONT POWER SEAT SWITCH LH


    B166949
  1. Install the switch with the 3 screws.

  1. Connect the connectors.



7. INSTALL FRONT SEAT CUSHION SHIELD INNER LH


B191015
  1. Attach the 2 claws and clip to install the cushion shield.

  1. Install the screw.



8. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (w/ Climate Control Seat System)


    B191260E02
  1. Install the front seat inner belt assembly LH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt to overlap the protruding part of the front seat adjuster.



    B191251
  1. Connect the connector and attach the 6 clamps.



9. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (w/o Climate Control Seat System)


    B191260E03
  1. Install the front seat inner belt assembly LH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt to overlap the protruding part of the front seat adjuster.



    B191250
  1. Connect the connector and attach the 5 clamps.



10. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)


    B191262E02
  1. Install the front seat inner belt assembly RH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt to overlap the protruding part of the front seat adjuster.



    B191253
  1. Connect the connector and attach the clamp.



11. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (w/ Climate Control Seat System)


    B191262E02
  1. Install the front seat inner belt assembly RH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt to overlap the protruding part of the front seat adjuster.



    B191254
  1. Connect the connector and attach the clamp.



12. INSTALL FRONT SEAT CUSHION SHIELD LH


    B166945
  1. Connect the switch connectors.

  1. Attach the 2 claws to install the cushion shield.

  1. Install the 3 screws.



    B195226E02
  1. Install the 2 screws.

  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with 2 new hog rings.



13. INSTALL RECLINING POWER SEAT SWITCH KNOB LH


B201574
  1. Attach the 2 claws to install the knob.



14. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB LH


B201575
  1. Attach the 2 claws to install the knob.



15. INSTALL FRONT SEAT ASSEMBLY LH
  1. Install the front seat (Click here).