STEERING PAD > DISPOSAL |
| 1. PRECAUTION |
| 2. DISPOSE OF STEERING PAD (When Installed in Vehicle) |
![]() |
Check the function of SST.
![]() |
Connect SST to the battery.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
| *1 | Battery |
![]() |
Check the function of SST.
Press the SST activation switch and check that the LED of the SST activation switch comes on.
Disconnect SST from the battery.
Read the precaution (Click here).
Disconnect the cable from the negative (-) battery terminal.
![]() |
Remove the lower steering column cover.
While turning the steering wheel assembly to the right and left, remove the 2 screws and lower steering column cover.
![]() |
Disconnect the yellow airbag connector from the spiral cable.
Slide the slider to release the lock, and then disconnect the connector.
| *1 | Slider |
![]() |
Install SST.
Connect the SST connector to the airbag connector of the spiral cable.
![]() |
Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.
| *1 | Battery |
| *a | 10 m or more |
While maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
Deploy the airbag.
Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.
Press the SST activation switch and deploy the airbag.
| 3. DISPOSE OF STEERING PAD (When not Installed in Vehicle) |
Check the function of SST (See previous step).
Remove the steering pad (Click here).
![]() |
Using a service-purpose wire harness for the vehicle, tie down the steering pad to an unneeded wheel.
| *a | Wire Diameter |
| *b | Stripped Wire |
![]() |
Install the 2 bolts with washers into the 2 bolt holes on the steering pad.
![]() |
Connect SST to the steering pad at the locations indicated by the arrows in the illustration.
![]() |
Wind 3 wire harnesses at least 2 times each around the bolts installed on the left and right sides of the steering pad.
| *a | 2 times or more |
![]() |
Face the airbag deployment side of the steering pad upward. Separately tie the left and right sides of the steering pad to a disc wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole of the disc wheel.
![]() |
Install SST.
Connect the SST connector.
![]() |
Move SST at least 10 m (32.8 ft.) away from the steering pad tied down to the disc wheel.
| *1 | Battery |
| *2 | Steering Pad |
| *a | 10 m or more |
![]() |
Cover the steering pad (using a cardboard box).
| *1 | Weight |
| *2 | Steering Pad |
Cover the steering pad with a cardboard box.
Place weights on the cardboard box in 4 places totaling at least 190 N (19 kg, 42.7 lb).
Cover the steering pad (using tires).
![]() |
Place at least 3 tires without disc wheels onto the disc wheel and tire to which the steering pad is tied.
| *1 | Inner Diameter |
| *2 | Width |
| *3 | Tires (3 or more) |
| *4 | Steering Pad |
Place a disc wheel and tire on top.
![]() |
Tie the tires together with the 2 wires.
Deploy the airbag.
![]() |
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
| *A | Using a Cardboard Box |
| *B | Using Tires |
| *1 | Battery |
| *2 | Steering Pad |
| *a | 10 m or more |
Check that no one is within a 10 m (32.8 ft.) radius of the disc wheel to which the steering pad is tied.
Press the SST activation switch and deploy the airbag.
Dispose of the steering pad.
Remove the steering pad from the disc wheel.
Place the steering pad in a plastic bag, tie it tightly and dispose of it according to local regulations.