Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory)

POWER MIRROR CONTROL SYSTEM (w/ Memory) > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body or Powertrain / (desired system) / Data List.

  5. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mirror Selection SW (R)
    Mirror master switch signal for RH mirror / ON or OFF
    ON: Switch is in R position
    OFF: Switch is off or in L position
    -
    Mirror Selection SW (L)
    Mirror master switch signal for LH mirror / ON or OFF
    ON: Switch is in L position
    OFF: Switch is off or in R position
    -
    Mirror Position SW (R)
    Mirror control switch signal (RIGHT) / ON or OFF
    ON: RIGHT switch is on
    OFF: Any switch except RIGHT is on or all switches are off
    -
    Mirror Position SW (L)
    Mirror control switch signal (LEFT) / ON or OFF
    ON: LEFT switch is on
    OFF: Any switch except LEFT is on or all switches are off
    -
    Mirror Position SW (UP)
    Mirror control switch signal (UP) / ON or OFF
    ON: UP switch is on
    OFF: Any switch except UP is on or all switches are off
    -
    Mirror Position SW (Dwn)
    Mirror control switch signal (DOWN) / ON or OFF
    ON: DOWN switch is on
    OFF: Any switch except DOWN is on or all switches are off
    -
    Outer Mirror Fold SW
    Mirror retract switch signal / ON or OFF
    ON: Switch is on (retracting)
    OFF: Switch is off
    -

    Mirror 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mirror Memory No. 1
    Mirror position memorized in seat memory switch 1 / ON or OFF
    ON: Memorized
    OFF: Not memorized
    -
    Mirror Memory No. 2
    Mirror position memorized in seat memory switch 2 / ON or OFF
    ON: Memorized
    OFF: Not memorized
    -
    RH Mir Position Sensor V
    Passenger side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V
    Within range from 0 to 5 V
    -
    RH Mir Position Sensor H
    Passenger side mirror horizontal sensor voltage / MIN: 0 V MAX: 5 V
    Within range from 0 to 5 V
    -
    LH Mir Position Sensor V
    Driver side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V
    Within range from 0 to 5 V
    -
    LH Mir Position Sensor H
    Driver side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V
    Within range from 0 to 5 V
    -
    ACC SW
    Ignition switch ACC signal / ON or OFF
    ON: Ignition switch ACC
    OFF: Ignition switch off
    -
    Driver Side SET Mem SW
    Driver side seat memory SET switch / ON or OFF
    ON: Driver side seat memory SET switch on
    OFF: Driver side seat memory SET switch off
    -
    Driver Side Memory SW 1
    Driver side seat memory switch 1 / ON or OFF
    ON: Driver side seat memory switch 1 on
    OFF: Driver side seat memory switch 1 off
    -
    Driver Side Memory SW 2
    Driver side seat memory switch 2 / ON or OFF
    ON: Driver side seat memory switch 2 on
    OFF: Driver side seat memory switch 2 off
    -
    Foot Light
    Foot light illumination time
    OFF/7.5 s/15 s/30 s
    -

    ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Shift SW States (R Range)
    PNP switch status / ON or OFF
    ON: Shift lever in R
    OFF Shift lever not in R
    -


PERFORM ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Mirror / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Mirror 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    RH Mirror Up/Down
    Mirror vertical operation
    UP/OFF/DOWN
    -
    RH Mirror Right/Left
    Mirror horizontal operation
    RIGHT/OFF/LEFT
    -
    LH Mirror Up/Down
    Mirror vertical operation
    UP/OFF/DOWN
    -
    LH Mirror Right/Left
    Mirror horizontal operation
    RIGHT/OFF/LEFT
    -
    Foot Light
    Foot light illumination operation
    ON/OFF
    -
    Mirror Fold
    Mirror retract operation
    FOLD/OFF
    -
    Mirror Return
    Mirror return operation
    RETURN/OFF
    -