POWER MIRROR CONTROL SYSTEM (w/ Memory) > Power Mirror cannot be Adjusted with Power Mirror Switch |

| 1.CHECK FOR DTC |
Use the intelligent tester to check if the CAN communication system is functioning normally (Click here).
| Result | Proceed to |
| CAN DTC is not output | A |
| CAN DTC is output | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Mirror Selection SW (R) | Mirror master switch signal for RH mirror / ON or OFF | ON: Switch is in R position OFF: Switch is off or in L position | - |
| Mirror Selection SW (L) | Mirror master switch signal for LH mirror / ON or OFF | ON: Switch is in L position OFF: Switch is off or in R position | - |
| Mirror Position SW (R) | Mirror control switch signal (RIGHT) / ON or OFF | ON: RIGHT switch is on OFF: Any switch except RIGHT is on or all switches are off | - |
| Mirror Position SW (L) | Mirror control switch signal (LEFT) / ON or OFF | ON: LEFT switch is on OFF: Any switch except LEFT is on or all switches are off | - |
| Mirror Position SW (UP) | Mirror control switch signal (UP) / ON or OFF | ON: UP switch is on OFF: Any switch except UP is on or all switches are off | - |
| Mirror Position SW (Dwn) | Mirror control switch signal (DOWN) / ON or OFF | ON: DOWN switch is on OFF: Any switch except DOWN is on or all switches are off | - |
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER MIRROR CONTROL FUNCTION) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Mirror / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| RH Mirror Up/Down | Mirror vertical operation | UP/OFF/DOWN | - |
| RH Mirror Right/Left | Mirror horizontal operation | RIGHT/OFF/LEFT | - |
| LH Mirror Up/Down | Mirror vertical operation | UP/OFF/DOWN | - |
| LH Mirror Right/Left | Mirror horizontal operation | RIGHT/OFF/LEFT | - |
| Result | Proceed to |
| Outer rear view mirror operates normally | A |
| Outer rear view mirror LH does not operate normally | B |
| Outer rear view mirror RH does not operate normally | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 4.INSPECT OUTER MIRROR SWITCH (MIRROR CONTROL SWITCH) |
![]() |
Remove the switch (Click here).
Select "L" on the mirror master switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
| 1 (MSW) - 2 (E) | L switch | Pressed | 100 Ω |
| Not Pressed | 10 kΩ or higher | ||
| 3 (M+) - 2 (E) | UP | Pressed | 100 Ω |
| Not Pressed | 10 kΩ or higher | ||
| DOWN | Pressed | 470 Ω | |
| Not Pressed | 10 kΩ or higher | ||
| LEFT | Pressed | 800 Ω | |
| Not Pressed | 10 kΩ or higher | ||
| RIGHT | Pressed | 250 Ω | |
| Not Pressed | 10 kΩ or higher | ||
Select "R" on the mirror master switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
| 1 (MSW) - 2 (E) | R switch | Pressed | Below 1 Ω |
| Not Pressed | 10 kΩ or higher | ||
| 3 (M+) - 2 (E) | UP | Pressed | 100 Ω |
| Not Pressed | 10 kΩ or higher | ||
| DOWN | Pressed | 470 Ω | |
| Not Pressed | 10 kΩ or higher | ||
| LEFT | Pressed | 800 Ω | |
| Not Pressed | 10 kΩ or higher | ||
| RIGHT | Pressed | 250 Ω | |
| Not Pressed | 10 kΩ or higher | ||
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU) |
![]() |
Disconnect the H4 ECU connector.
Disconnect the J6 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J6-1 (MSW) - H4-12 (MIRS) | Always | Below 1 Ω |
| J6-1 (MSW) - Body ground | Always | 10 kΩ or higher |
| J6-2 (E) - H4-2 (MIRE) | Always | Below 1 Ω |
| J6-2 (E) - Body ground | Always | 10 kΩ or higher |
| J6-3 (M+) - H4-11 (MIRB) | Always | Below 1 Ω |
| J6-3 (M+) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH |
![]() |
Remove the mirror LH (Click here).
Check the outer mirror motor operation.
Apply battery voltage and check operation of the mirror face.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 10 (MV) Battery negative (-) → Terminal 11 (M+) | Turns upward (A) |
| Battery positive (+) → Terminal 11 (M+) Battery negative (-) → Terminal 10 (MV) | Turns downward (B) |
| Battery positive (+) → Terminal 11 (M+) Battery negative (-) → Terminal 12 (MH) | Turns left (C) |
| Battery positive (+) → Terminal 12 (MH) Battery negative (-) → Terminal 11 (M+) | Turns right (D) |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU) |
![]() |
Disconnect the M8 ECU connector.
Disconnect the M5 mirror connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M5-10 (MV) - M8-20 (MVL) | Always | Below 1 Ω |
| M5-10 (MV) - Body ground | Always | 10 kΩ or higher |
| M5-11 (M+) - M8-18 (M+L) | Always | Below 1 Ω |
| M5-11 (M+) - Body ground | Always | 10 kΩ or higher |
| M5-12 (MH) - M8-19 (MHL) | Always | Below 1 Ω |
| M5-12 (MH) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH |
![]() |
Remove the mirror RH (Click here).
Check the outer mirror motor operation.
Apply battery voltage and check operation of the mirror face.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 10 (MV) Battery negative (-) → Terminal 11 (M+) | Turns upward (A) |
| Battery positive (+) → Terminal 11 (M+) Battery negative (-) → Terminal 10 (MV) | Turns downward (B) |
| Battery positive (+) → Terminal 11 (M+) Battery negative (-) → Terminal 12 (MH) | Turns left (C) |
| Battery positive (+) → Terminal 12 (MH) Battery negative (-) → Terminal 11 (M+) | Turns right (D) |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU) |
![]() |
Disconnect the M8 ECU connector.
Disconnect the L6 mirror connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L6-10 (MV) - M8-40 (MVR) | Always | Below 1 Ω |
| L6-10 (MV) - Body ground | Always | 10 kΩ or higher |
| L6-11 (M+) - M8-38 (M+R) | Always | Below 1 Ω |
| L6-11 (M+) - Body ground | Always | 10 kΩ or higher |
| L6-12 (MH) - M8-39 (MHR) | Always | Below 1 Ω |
| L6-12 (MH) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||