Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory)

POWER MIRROR CONTROL SYSTEM (w/ Memory) > Power Mirror cannot be Adjusted with Power Mirror Switch

for Preparation Click here


SYSTEM DESCRIPTION

This circuit detects the conditions of the outer mirror switch.
The outer mirror switch sends information about the operating condition of the mirror switch (switch input signals) through the CAN communication line. Then the switch input signals are sent to the outer mirror control ECU. Mirror adjustment is controlled by the outer mirror control ECU.

WIRING DIAGRAM


B191614E01


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Use the intelligent tester to check if the CAN communication system is functioning normally (Click here).
    Result 
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mirror Selection SW (R)
    Mirror master switch signal for RH mirror / ON or OFF
    ON: Switch is in R position
    OFF: Switch is off or in L position
    -
    Mirror Selection SW (L)
    Mirror master switch signal for LH mirror / ON or OFF
    ON: Switch is in L position
    OFF: Switch is off or in R position
    -
    Mirror Position SW (R)
    Mirror control switch signal (RIGHT) / ON or OFF
    ON: RIGHT switch is on
    OFF: Any switch except RIGHT is on or all switches are off
    -
    Mirror Position SW (L)
    Mirror control switch signal (LEFT) / ON or OFF
    ON: LEFT switch is on
    OFF: Any switch except LEFT is on or all switches are off
    -
    Mirror Position SW (UP)
    Mirror control switch signal (UP) / ON or OFF
    ON: UP switch is on
    OFF: Any switch except UP is on or all switches are off
    -
    Mirror Position SW (Dwn)
    Mirror control switch signal (DOWN) / ON or OFF
    ON: DOWN switch is on
    OFF: Any switch except DOWN is on or all switches are off
    -

    OK:
    On the intelligent tester screen, each item changes between ON and OFF according to above chart.



NG
Go to step 4
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER MIRROR CONTROL FUNCTION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Mirror / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    Mirror 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    RH Mirror Up/Down
    Mirror vertical operation
    UP/OFF/DOWN
    -
    RH Mirror Right/Left
    Mirror horizontal operation
    RIGHT/OFF/LEFT
    -
    LH Mirror Up/Down
    Mirror vertical operation
    UP/OFF/DOWN
    -
    LH Mirror Right/Left
    Mirror horizontal operation
    RIGHT/OFF/LEFT
    -
    Result 
    Result
    Proceed to
    Outer rear view mirror operates normally
    A
    Outer rear view mirror LH does not operate normally
    B
    Outer rear view mirror RH does not operate normally
    C



B
Go to step 6

C
Go to step 8
A

REPLACE OUTER MIRROR CONTROL ECU (Click here)  

4.INSPECT OUTER MIRROR SWITCH (MIRROR CONTROL SWITCH)


    B167772E06
  1. Remove the switch (Click here).

  1. Select "L" on the mirror master switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (MSW) - 2 (E)
    L switch
    Pressed
    100 Ω
    Not Pressed
    10 kΩ or higher
    3 (M+) - 2 (E)
    UP
    Pressed
    100 Ω
    Not Pressed
    10 kΩ or higher
    DOWN
    Pressed
    470 Ω
    Not Pressed
    10 kΩ or higher
    LEFT
    Pressed
    800 Ω
    Not Pressed
    10 kΩ or higher
    RIGHT
    Pressed
    250 Ω
    Not Pressed
    10 kΩ or higher

  1. Select "R" on the mirror master switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (MSW) - 2 (E)
    R switch
    Pressed
    Below 1 Ω
    Not Pressed
    10 kΩ or higher
    3 (M+) - 2 (E)
    UP
    Pressed
    100 Ω
    Not Pressed
    10 kΩ or higher
    DOWN
    Pressed
    470 Ω
    Not Pressed
    10 kΩ or higher
    LEFT
    Pressed
    800 Ω
    Not Pressed
    10 kΩ or higher
    RIGHT
    Pressed
    250 Ω
    Not Pressed
    10 kΩ or higher



NG
REPLACE OUTER MIRROR SWITCH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU)


    B193661E01
  1. Disconnect the H4 ECU connector.

  1. Disconnect the J6 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J6-1 (MSW) - H4-12 (MIRS)
    Always
    Below 1 Ω
    J6-1 (MSW) - Body ground
    Always
    10 kΩ or higher
    J6-2 (E) - H4-2 (MIRE)
    Always
    Below 1 Ω
    J6-2 (E) - Body ground
    Always
    10 kΩ or higher
    J6-3 (M+) - H4-11 (MIRB)
    Always
    Below 1 Ω
    J6-3 (M+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) 

6.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH


    B166373E02
  1. Remove the mirror LH (Click here).

  1. Check the outer mirror motor operation.

    1. Apply battery voltage and check operation of the mirror face.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 10 (MV)
      Battery negative (-) → Terminal 11 (M+)
      Turns upward (A)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 10 (MV)
      Turns downward (B)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 12 (MH)
      Turns left (C)
      Battery positive (+) → Terminal 12 (MH)
      Battery negative (-) → Terminal 11 (M+)
      Turns right (D)



NG
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)


    B193662E01
  1. Disconnect the M8 ECU connector.

  1. Disconnect the M5 mirror connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M5-10 (MV) - M8-20 (MVL)
    Always
    Below 1 Ω
    M5-10 (MV) - Body ground
    Always
    10 kΩ or higher
    M5-11 (M+) - M8-18 (M+L)
    Always
    Below 1 Ω
    M5-11 (M+) - Body ground
    Always
    10 kΩ or higher
    M5-12 (MH) - M8-19 (MHL)
    Always
    Below 1 Ω
    M5-12 (MH) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER MIRROR CONTROL ECU (Click here)  

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH


    B166376E03
  1. Remove the mirror RH (Click here).

  1. Check the outer mirror motor operation.

    1. Apply battery voltage and check operation of the mirror face.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 10 (MV)
      Battery negative (-) → Terminal 11 (M+)
      Turns upward (A)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 10 (MV)
      Turns downward (B)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 12 (MH)
      Turns left (C)
      Battery positive (+) → Terminal 12 (MH)
      Battery negative (-) → Terminal 11 (M+)
      Turns right (D)



NG
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)


    B193662E02
  1. Disconnect the M8 ECU connector.

  1. Disconnect the L6 mirror connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L6-10 (MV) - M8-40 (MVR)
    Always
    Below 1 Ω
    L6-10 (MV) - Body ground
    Always
    10 kΩ or higher
    L6-11 (M+) - M8-38 (M+R)
    Always
    Below 1 Ω
    L6-11 (M+) - Body ground
    Always
    10 kΩ or higher
    L6-12 (MH) - M8-39 (MHR)
    Always
    Below 1 Ω
    L6-12 (MH) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER MIRROR CONTROL ECU (Click here)