Meter/Gauge
Item
| Details
|
Speedometer
| Based on signal received from wheel speed sensor, skid control ECU calculates vehicle speed and transmits data to combination meter (CAN).
|
ODO/TRIP meter
| - Combination meter receives vehicle speed pulse integration signal from skid control ECU, and ODO/TRIP meter display operates (CAN).
- Using ODO/TRIP switch, ODO/TRIP meter display changes.
|
Tachometer
| Combination meter receives engine rpm signal from ECM, and gauge needle operates (CAN).
|
Engine coolant temperature gauge
| Combination meter receives water temperature signal from ECM, and gauge needle operates (CAN).
|
Fuel receiver gauge
| Combination meter receives fuel amount information measured by fuel sender gauge, and gauge needle operates (Direct line).
|
Voltage meter
| Monitors IG voltage and gauge needle operates (Direct line).
|
Oil pressure receiver gauge
| Combination meter receives engine rpm signal from ECM (CAN), and receives oil pressure sender signal from oil pressure sender (Direct line). Then meter measures signals and gauge needle operates.
|
A/T oil temperature receiver gauge*1
| Combination meter receives A/T oil temperature signal from ECM, and gauge needle operates (CAN).
|
Warning/Indicator
Item
| Details
|
BEAM indicator light

| Receives signal from main body ECU (CAN).
|
A/T OIL TEMP warning light

| Warning is displayed when oil temperature is high (CAN).
|
SRS warning light

| Receives malfunction signal from airbag sensor (CAN).
|
DOOR indicator light

| Open door indicator comes on when signal is received from main body ECU (CAN).
|
Driver side seat belt warning light

| Receives driver seat belt signal (Unfastened) from main body ECU (CAN).
|
Brake warning light

| - Comes on when parking brake switch is ON (CAN).
- Brake fluid level warning switch is ON (Direct line).
- Vehicle stability control system is malfunctioning.
|
CHARGE warning light

| Receives malfunction signal from generator (Direct line).
|
ABS warning light

| Receives malfunction signal from skid control ECU (CAN).
|
MIL

| Receives malfunction signal from ECM (Direct line).
|
FUEL warning light

| Receives fuel empty signal from fuel sender gauge (Direct line).
|
SLIP indicator light

| Receives malfunction signal from skid control ECU (CAN).
|
WASHER warning light*1

| Warning is displayed when the washer level is low (Direct line).
|
CRUISE main indicator light

| Receives CRUISE on signal or malfunction signal from ECM (CAN).
|
TAIL indicator light

| Receives taillight or headlight signal from main body ECU (CAN).
|
Turn signal indicator light (LH/RH)

| Receives turn signal from FLASHER relay (Direct line).
|
VSC OFF indicator light

| Receives VSC system fail-safe control signal from skid control ECU (CAN).
|
TRC OFF indicator light

| Receives VSC OFF switch ON signal from skid control ECU (CAN).
|
RSCA OFF indicator light

| Receives RSCA OFF signal from airbag sensor (Direct line).
|
EPS warning light

| Receives malfunction signal from power steering ECU (CAN).
|
Master warning light*2

| Receives warning signal from each ECU (CAN).
|
Height control MAN. indicator light

| Receives a suspension control manual signal from the suspension control ECU (CAN).
|
SPEED LIMIT indicator light

| Receives a vehicle speed signal from the skid control ECU (CAN).
|
4LO indicator light*3

| Receives 4LO signal from 4WD control ECU (CAN).
|
4HI indicator light*3

| Receives 4HI signal from 4WD control ECU (CAN).
|
CENTER DIFF. indicator light*3

| Receives a DIFF. LOCK signal from 4WD control ECU (CAN).
|
Height control HI indicator light
| Receives a suspension position HI signal from suspension control ECU (CAN).
|
Height control N indicator light
| Receives a suspension position N signal from suspension control ECU (CAN).
|
Height control LO indicator light
| Receives a suspension position LO signal from suspension control ECU (CAN).
|
A/T P shift position indicator
| Receives P signal from ECM (Direct line).
|
A/T R shift position indicator
| Receives R signal from ECM (Direct line).
|
A/T N shift position indicator
| Receives N signal from ECM (Direct line).
|
A/T D shift position indicator
| Receives D signal from ECM (Direct line).
|
A/T S shift position indicator
| Receives S signal from ECM (Direct line).
|
A/T 6 shift position indicator
| Receives 6 signal from ECM (CAN).
|
A/T 5 shift position indicator
| Receives 5 signal from ECM (CAN).
|
A/T 4 shift position indicator
| Receives 4 signal from ECM (CAN).
|
A/T 3 shift position indicator
| Receives 3 signal from ECM (CAN).
|
A/T 2 shift position indicator
| Receives 2 signal from ECM (CAN).
|
A/T 1 shift position indicator
| Receives 1 signal from ECM (CAN).
|