Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > OPERATION CHECK

for Preparation Click here



INSPECT INDICATOR/WARNING LIGHT

HINT:
In this inspection, an indicator or warning light might come on differently than is specified, under some normal conditions.

  1. Check the following indicators and warning lights.
    Warning/Indicator Light
    Switch Condition
    Specified Condition
    Height control HI indicator light
    Ignition switch off → ON
    Comes on for 2 seconds
    Height control N indicator light
    Ignition switch off → ON
    Comes on for 2 seconds
    Height control LO indicator light
    Ignition switch off → ON
    Comes on for 2 seconds
    Height control MAN. indicator light
    Ignition switch off → ON
    Comes on for 2 seconds
    Brake warning light
    Ignition switch off → ON
    Comes on for 3 seconds
    ABS warning light
    Ignition switch off → ON
    Comes on for 3 seconds
    SLIP indicator light
    Ignition switch off → ON
    Comes on for 3 seconds
    VSC OFF indicator light
    Ignition switch off → ON
    Comes on for 3 seconds
    RSCA OFF indicator light
    Ignition switch off → ON
    Comes on for 3 seconds
    EPS warning light
    Ignition switch off → ON
    Comes on for 3 seconds
    SRS warning light
    Ignition switch off → ON
    Comes on for 6 seconds
    A/T OIL TEMP warning light
    Ignition switch off → ON
    Illuminates when ignition switch is turned to ON.
    Turns off when engine is started.
    CHARGE warning light
    Ignition switch off → ON
    Illuminates when ignition switch is turned to ON.
    Turns off when engine is started.
    MIL
    Ignition switch off → ON
    Illuminates when ignition switch is turned to ON.
    Turns off when engine is started.


INSPECT SPEEDOMETER
  1. Using a speedometer tester, check that the speedometer reading is within the allowable range shown in the table below. Also, check for proper operation of the odometer.

    Reference:
    for km/h 
    Standard Indication
    Acceptable Range
    Data in ( ) is for reference
    20 km/h
    (215 to 25 km/h)
    40 km/h
    41.7 to 46.2 km/h
    60 km/h
    62.7 to 67.2 km/h
    80 km/h
    83.4 to 88.4 km/h
    100 km/h
    104.3 to 109.3 km/h
    120 km/h
    125.1 to 130.6 km/h
    140 km/h
    145.8 to 151.8 km/h
    160 km/h
    166.2 to 173.2 km/h
    180 km/h
    186.9 to 194.5 km/h

    NOTICE:
    Do not use worn, underinflated or overinflated tires, as the speedometer reading will be inaccurate.

  2. Check the deflection width of the speedometer indicator.

    Reference:
    0.5 km/h (0.3 mph)


INSPECT TACHOMETER
  1. Connect a tune-up tachometer, and start the engine.

  2. Compare the test results with the tachometer indicator.

    DC 13.5 V, at 25°C (77°F):
    Standard indication (rpm)
    Acceptable range
    Data in ( ) is for reference
    700
    630 to 770
    1000
    (900 to 1100)
    2000
    (1850 to 2150)
    3000
    2800 to 3200
    4000
    (3800 to 4200)
    5000
    4800 to 5200
    6000
    (5750 to 6250)

    If the result is not as specified, the speedometer may have a malfunction.


INSPECT METER/GAUGE
  1. Connect the intelligent tester to the DLC3.

  2. Perform Active Test (Click here).

    OK:
    All meter/gauge needle indicators are normal.


INSPECT WARNING/INDICATOR LIGHT
  1. Connect the intelligent tester to the DLC3.

  2. Perform Active Test (Click here).

    OK:
    Each warning/indicator light turns ON and OFF using tester.


INSPECT MULTI-INFORMATION DISPLAY (w/ Multi-information display)
  1. Connect the intelligent tester to the DLC3.

  2. Perform Active Test (Click here).

    HINT:
    If this Active Test is being performed and the ignition switch is turned off and then ON, the A/T and ODO/TRIP display background may turn white. If this occurs, end this Active Test and turn the ignition switch off.

    OK:
    All dots in the multi-information display turn ON and OFF using intelligent tester.