Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Speedometer Malfunction

for Preparation Click here


DESCRIPTION

The combination meter receives vehicle speed signals from the skid control ECU via the CAN line. The vehicle speed sensor detects the voltage that varies according to the vehicle speed. The skid control ECU supplies power to the vehicle speed sensor. The skid control ECU detects vehicle speed signals based on the pulses of the voltage.

WIRING DIAGRAM


E140490E21


INSPECTION PROCEDURE

1.CHECK DTC
  1. Use the intelligent tester to check if the CAN communication system is functioning normally (Click here).
    Result 
    Result
    Proceed to
    CAN communication DTC is not output
    A
    CAN communication DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK SFI SYSTEM (VEHICLE SPEED)
  1. Use the intelligent tester to check if the SFI system is functioning normally (Click here).



NG
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SPEEDOMETER)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Speed Meter Operation
    Speedometer
    0, 40, 80, 120, 160, 200, 240 or 280
    -

    OK:
    Needle indication is normal.

    HINT:
    1. Confirm that the vehicle is stopped and engine is idling. It is normal that door will be locked automatically when performing the speedometer Active Test.
    2. The displayed value has the same units (km/h, mph) as the main scale of the vehicle speedometer.
    3. The needle position should be within the acceptable tolerance.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


4.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed/Min.: 0 (0), Max.: 255 (158)
    Almost same as actual speed (when driving)
    Unit: km/h (mph)

    OK:
    Vehicle speed displayed on the intelligent tester is almost the same as actual vehicle speed measured using speedometer tester (calibrated chassis dynamometer).



NG
Go to step 5
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

5.READ VALUE USING INTELLIGENT TESTER (WHEEL SPEED SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    (FL/FR/RL/RR) Wheel Speed
    Wheel speed sensor (FL/FR/RL/RR) reading/Min.: 0 (0), Max.: 326 (202)
    Actual wheel speed
    Similar speed as indicated on speedometer

    OK:
    Vehicle speed displayed on the intelligent tester is almost the same as actual vehicle speed measured using speedometer tester (calibrated chassis dynamometer).



NG
REPLACE VSC ACTUATOR ASSEMBLY (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)