Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR

FRONT DOOR > DISASSEMBLY

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the RH side.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH (for 14 Speakers)


    B190538
  1. Detach the 3 clips and remove the front door lower frame bracket garnish.

  1. Disconnect the connector.



3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    B194240
  1. Detach the 3 clips and remove the front door lower frame bracket garnish.



4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B190539
  1. Using a moulding remover, detach the 4 claws and remove the front door inside handle bezel plug.



5. REMOVE FRONT ARMREST BASE UPPER PANEL


    B190537
  1. Detach the 2 clips and 5 claws and remove the front armrest base upper panel.

  1. Disconnect the connector.



6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


B190541
  1. Remove the front door armrest cover.

  1. Remove the 2 screws.



    B190542
  1. Detach the 10 clips.

  1. Disconnect the connector.



    B190543
  1. Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door trim board sub-assembly.



7. REMOVE SEAT MEMORY SWITCH (for Driver Side with Memory)


    B194034
  1. Remove the 2 screws and seat memory switch.



8. REMOVE FRONT DOOR INSIDE HANDLE BEZEL


    B190544
  1. Remove the 4 screws and remove the front door inside handle bezel.



9. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B190545
  1. Remove the 3 screws and remove the front door inside handle sub-assembly.



10. REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP


    B195434
  1. Raise the 8 claws of the front door glass inner weatherstrip and then remove the front door glass inner weatherstrip from the front door trim board sub-assembly, as shown in the illustration.



11. REMOVE SIDE AIR BAG SENSOR ASSEMBLY

CAUTION:
Confirm that the cable is disconnected from the battery negative (-) terminal. Even an impact to only the airbag sensor will cause the airbag to deploy.



    B194500E01
  1. Slide the outer housing and disconnect the airbag connector.

  1. Remove the bolt.

  1. Detach the guide and remove the side airbag sensor.



12. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY


    E161072
  1. Disconnect the speaker connector.

  1. Remove the 4 screws.



    E161076
  1. Detach the 3 claws and remove the speaker.

    NOTICE:
    Do not touch the cone part of the speaker.



13. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY


B190501
  1. Disconnect the connector.

  1. Remove the 3 nuts.

  1. Detach the claw and remove the outer rear view mirror assembly.



14. REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


B191700E01
  1. Apply protective tape to the door panel in the area around the front door glass outer weatherstrip.



    B191701E01
  1. Using a moulding remover, detach the 5 claws and the clip, and remove the front door glass outer weatherstrip.



15. REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side with Memory)


    B192565
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and remove the outer mirror control ECU assembly.



16. REMOVE FRONT DOOR NO. 1 TRIM BRACKET


    B190549
  1. Remove the 2 screws and remove the front door No. 1 trim bracket.



17. REMOVE FRONT DOOR SERVICE HOLE COVER


    B190551
  1. Disconnect the connectors and detach the clamps.



    B195025
  1. Remove the front door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.



18. REMOVE FRONT DOOR GLASS RUN


    B190552
  1. Remove the front door glass run.



19. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


B190553
  1. Provisionally install the power window switch.

  1. Move the front door glass until the 2 bolts can be seen through the service holes.

  1. Remove the 2 bolts.

    NOTICE:
    Do not drop or damage the front door glass subassembly when removing the bolts.



    B195026
  1. Remove the front door glass sub-assembly in the direction indicated by the arrows in the illustration.

    NOTICE:
    Do not damage the front door glass subassembly.

  1. Remove the power window switch.



20. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY


    B190554E01
  1. Disconnect the connector.

  1. Loosen bolt A.

  1. Remove the 5 bolts, then remove the front door window regulator sub-assembly.

    NOTICE:
    Do not drop or damage the front door window regulator sub-assembly when removing the bolts.

    HINT:
    Remove the front door window regulator sub-assembly through the service hole.



21. REMOVE FRONT DOOR FRAME FRONT LOWER SUB-ASSEMBLY


    B190555
  1. Remove the 2 bolts and remove the front door frame front lower sub-assembly.

    NOTICE:
    Do not drop or damage the front door frame front lower sub-assembly when removing the bolt.



22. REMOVE FRONT DOOR FRAME REAR LOWER SUB-ASSEMBLY


    B190556
  1. Remove the 2 bolts and remove the front door frame rear lower sub-assembly.

    NOTICE:
    Do not drop or damage the front door frame rear lower sub-assembly when removing the bolt.



23. REMOVE FRONT NO. 1 DOOR STIFFENER CUSHION


    B190557
  1. Detach the 2 clips and remove the front No. 1 door stiffener cushion.



24. REMOVE FRONT DOOR CHECK ASSEMBLY


    B190558
  1. Remove the 2 nuts and bolt and remove the front door check assembly.



25. REMOVE FRONT DOOR WEATHERSTRIP


    B190559
  1. Detach the 39 clips and remove the front door weatherstrip.



26. REMOVE FRONT DOOR PANEL PROTECTOR


    B190560
  1. Detach the 8 clips and remove the front door panel protector.



27. REMOVE FRONT DOOR OUTSIDE HANDLE COVER


    B190562
  1. Remove the hole plug.

  1. Using a T30 "TORX" socket, loosen the screw and remove the front door outside handle cover.



28. REMOVE DOOR LOCK CYLINDER (for Driver Side)


    B190567
  1. Detach the 2 claws and remove the door lock cylinder.



29. REMOVE FRONT DOOR LOCK


    B190561
  1. Using a T30 "TORX" socket wrench, remove the 3 screws.

  1. Slide the front door lock downward, pull out the front door lock open rod from the outside handle frame, and remove the front door lock and cables as a unit.

  1. Remove the door lock wire harness seal from the front door lock.



    B192551
  1. Remove the front door lock remote control cable.



    B192552E01
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 3 claws and open the cover.



    B192554
  1. Remove the front door inside locking cable.



30. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    B190563
  1. Remove the front door handle assembly by sliding and pulling it in the direction indicated by the arrow mark in the illustration.



31. REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD


    B190565
  1. Detach the 2 claws and remove the front door outside handle rear pad.



32. REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD


    B190566
  1. Detach the 3 claws and remove the front door outside handle front pad.



33. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    B190568
  1. Using a T30 "TORX" socket, loosen the screw.

  1. Detach the claw and slide the front door outside handle frame sub-assembly to remove it.



34. REMOVE CUSHION


    B190570
  1. Remove the cushions from the door panel.